2012 MITSUBISHI ECLIPSE light

Vehicle care and maintenance
7-61
7
4. Insert the tip of the screwdriver at the edge of the light
unit, pry gently to remove the light unit.
Then move the light unit toward the rear of the vehicle
and remove the clip (F).NOTE
Wrap a cloth around the tip of the screwdriver to keep
from scratching the lens.5. Remove the socket and bulb assemblies by turning them
counterclockwise.
Remove the bulb by pulling it out.
G- Back-up light
H- Rear turn signal light
I- Rear side-marker light
BK0132701US.book 61 ページ ２０１０年１２月６日　月曜日　午後２時３分

7-62 Vehicle care and maintenance
7
6. To install the bulb, perform the removal steps in reverse.NOTE
When mounting the light unit, align the clip (F), pins and
bolts (J) on the light unit with the holes in the body.
ECLIPSE SPYDER1. Open the trunk lid.
Push the center of the clips (A) and remove them. Then
remove the cover (B).
BK0132701US.book 62 ページ ２０１０年１２月６日　月曜日　午後２時３分

7-64 Vehicle care and maintenance
7
Grasp the trim cover and pull it toward you to remove the
clips.4. Lift the trim cover. Remove the light case mounting nut
(E).
1
2BK0132701US.book 64 ページ ２０１０年１２月６日　月曜日　午後２時３分

Vehicle care and maintenance
7-65
7
5. Insert the tip of the screwdriver at the edge of the light
unit, pry gently to remove the light unit.
Then move the light unit toward the rear of the vehicle
and remove the clip (F).NOTE
Wrap a cloth around the tip of the screwdriver to keep
from scratching the lens.6. Remove the socket and bulb assemblies by turning them
counterclockwise.
Remove the bulb by pulling it out.
G- Back-up light
H- Rear turn signal light
I- Rear side-marker light
BK0132701US.book 65 ページ ２０１０年１２月６日　月曜日　午後２時３分

7-66 Vehicle care and maintenance
7
7. To install the bulb, perform the removal steps in reverse.NOTE
When mounting the light unit, align the clip (F), pins and
bolts (J) on the light unit with the holes in the body.
License plate light
N00944000272
1. Remove the mounting screws (A) and remove the light
unit (B).
BK0132701US.book 66 ページ ２０１０年１２月６日　月曜日　午後２時３分

7-68 Vehicle care and maintenance
7
Dome light (Rear) (ECLIPSE only)
N00944100303
1. Insert the tip of a screwdriver at the edge of the lens, pry
gently to remove the lens, and then remove the bulb from
the light holder.NOTE
Wrap a cloth around the tip of the screwdriver to keep
from scratching the lens.
2. To install the bulb, perform the removal steps in reverse.
Dome light (Front)/Reading light
N00944500277
ECLIPSE (except for vehicles with sunroof)1. Insert the tip of a screwdriver at the edge of the lens, pry
gently to remove the lens, and then remove the bulb from
the light holder.NOTE
Wrap a cloth around the tip of the screwdriver to keep
from scratching the lens.
2. To install the bulb, perform the removal steps in reverse.ECLIPSE (vehicles with sunroof)/ECLIPSE SPYDERHave the dome light (front)/reading light bulbs replaced at an
authorized Mitsubishi Motors dealer or a repair facility of your
choice.
* - Front of the vehicle
*
BK0132701US.book 68 ページ ２０１０年１２月６日　月曜日　午後２時３分

Vehicle care and maintenance
7-69
7
Reading lights on an inside rearview mirror
(ECLIPSE SPYDER only, if so equipped)
N00944400188
Have the reading light bulbs replaced at an authorized
Mitsubishi Motors dealer or a repair facility of your choice.
Cargo area light (ECLIPSE only)
N00950000062
1. Insert the tip of a screwdriver at the edge of the lens, pry
gently to remove the lens, and then remove the bulb from
the light holder.
2. To install the bulb, perform the removal steps in reverse.Glove compartment light
N00954200059
Have the glove compartment light bulbs replaced at an autho-
rized Mitsubishi Motors dealer or a repair facility of your
choice.
BK0132701US.book 69 ページ ２０１０年１２月６日　月曜日　午後２時３分

7-70 Vehicle care and maintenance
7
Vanity mirror light
(if so equipped)
N00952800077
ECLIPSE1. Insert the tip of a screwdriver at the edge of the lens, pry
gently to remove the lens, and then remove the bulb from
the light holder.NOTE
Wrap a cloth around the tip of the screwdriver to keep
from scratching the lens.
2. To install the bulb, perform the removal steps in reverse.
ECLIPSE SPYDER1. Insert the tip of a screwdriver into the notch of the lens,
pry gently to remove the lens, and then remove the bulb
from the light holder.NOTE
Wrap a cloth around the tip of the screwdriver to keep
from scratching the lens.
BK0132701US.book 70 ページ ２０１０年１２月６日　月曜日　午後２時３分