2012 MERCEDES-BENZ G-Class light

Switching the seat heating on/off
General notes The red indicator lamps in the button indicate
the heating level you have selected.
i If the battery voltage is too low, the seat
heating may switch off.
One or more of the indicator lamps in the
seat heating button are flashing.
X Make sure that the SmartKey is in position
2 in the ignition lock.
Front-seat heating i
The system automatically switches down
from level 3 to level 2 after approximately
five minutes.
The system automatically switches down
from level 2 to level 1 after approximately
ten minutes.
The system automatically switches off
approximately 20 minutes after it is set to
level 1.
X To switch on: press button : repeatedly
until the desired heating level is set.
X To switch off: press button : repeatedly
until all the indicator lamps go out. Rear-seat heating
:
Level 1 (normal heating)
; Level 2 (rapid heating)
i The system automatically switches down
from level 2 (rapid heating) to level 1
(normal heating) after approximately five
minutes.
The system automatically switches off
approximately 30 minutes after it is set to
level 1.
X To select level 1: press the upper section
of button :.
An indicator lamp lights up.
X To deactivate level 1: press the upper
section of button :.
The indicator lamp goes out.
X To select level 2: press the lower section
of button ;.
Both indicator lamps light up.
X To deactivate level 2: press the lower
section of button ;.
Both indicator lamps go out. 80
Seats
Seats, steering wheel and mirrors

Problems with the seat heating
If one or all of the indicator lamps in the seat
heating button are flashing, the seat heating
has switched off automatically. The vehicle's
electrical system voltage is too low because
too many electrical consumers are switched
on.
X
Switch off electrical consumers which you
do not need, such as the rear window
defroster or interior lighting.
Once the
battery is sufficiently charged, the
seat heating will switch back on
automatically. Switching the seat ventilation on/off
Switching on/off Seat ventilation is only available for the front
seats.
The
three

blue indicator lamps in the buttons
indicate the ventilation level you have
selected.
i If the battery voltage is too low, the seat
ventilation may switch off. X
Make sure that the SmartKey is in position
2 in the ignition lock.
X To switch on: press button : repeatedly
until the desired ventilation level is set.
i If you open the side windows and the
sliding sunroof using the SmartKey
(Y page 69), the driver's seat ventilation
automatically switches

to the highest level.X
To switch off: press button : repeatedly
until all the indicator lamps go out.
Problems with the seat ventilation If one or all of the indicator lamps in the seat
ventilation button are flashing, the seat
ventilation has switched off automatically.
The vehicle's electrical system voltage is too
low because too many electrical consumers
are switched on.
X
Switch off electrical consumers that you do
not need, such as the rear window
defroster or interior lighting.
Once the

battery is sufficiently charged, the
seat ventilation will switch back on
automatically. Steering wheel
Important safety notes
You can

adjust the steering wheel electrically. G
WARNING
Do not adjust the steering wheel while driving.
Adjusting the steering wheel while driving
could cause the driver to lose control of the
vehicle.
The electrical steering wheel adjustment
feature can be operated at any time.
Therefore, do not leave children unattended
in the vehicle, or with access to an unlocked
vehicle. A child's unsupervised access to a
vehicle could result in an accident and/or
serious personal injury.
When you adjust the steering wheel, make
sure that:
R the steering wheel can be reached with
your arms slightly bent.
R you can move your legs freely.
R you can see all the displays in the
instrument cluster clearly. Steering wheel
81
Seats, steering wheel and mirrors Z

Adjusting the steering wheel
:
To adjust the steering wheel position
(fore-and-aft adjustment)
; To adjust the steering wheel height
X Make sure that the SmartKey is in position
1 or 2 in the ignition lock.
i If the driver's door is open, the steering
wheel can

be adjusted for up to 30 minutes
after the ignition has been switched off.
X Press the lever in the direction of
arrow : or ; until the steering wheel is
in the desired position.
You can find more information under:
R EASY-ENTRY/EXIT feature (

Y page 83)
R Storing settings ( Y page 85)Steering wheel heating
Switching on/off The steering-wheel heating heats the leather
areas of the steering wheel. :
To switch on the steering-wheel heating
; Indicator lamp
= To switch off the steering-wheel heating
X To switch on/off: make sure that the
SmartKey is

in position 1 or 2 in the ignition
lock.
X Turn the lever in the direction of arrow :
or =.
Indicator lamp ; lights up or goes out.
i The steering wheel heating does not
switch off automatically.
i The steering

wheel heating may switch off
temporarily if:
R the temperature of the vehicle interior is
above 86 ‡ (30 †).
R the temperature of the steering wheel is
above 95 ‡ (35 †).
Indicator lamp ; remains on.
i The steering wheel heating is deactivated
if you remove the SmartKey from the
ignition lock. 82
Steering wheel
Seats, steering wheel and mirrors

Problems with the steering wheel
heating
If steering wheel heating indicator lamp
; is
flashing, the steering wheel heating has
switched off automatically. The vehicle's
electrical system voltage is too low because
too many electrical consumers are switched
on.
X Switch off electrical consumers which you
do not need, such as the rear window
defroster or interior lighting.
Once the
battery is sufficiently charged, the
steering wheel heating will switch back on
automatically. Steering wheel EASY-ENTRY/EXIT
feature
General notes The EASY-ENTRY/EXIT feature makes getting
in and out of your vehicle easier.
You can activate and deactivate the EASY-
ENTRY/EXIT feature in the on-board
computer (Y page 161).
Important safety notes
G
WARNING
You must make sure no one can become
trapped or injured by the moving steering
wheel when the EASY-ENTRY/EXIT feature is
activated.
To stop steering maneuver do one of the
following:
R press the steering column adjustment
switch.
R press one of the memory function position
buttons.
R press the memory button.
Do not leave children unattended in the
vehicle, or

with access to an unlocked vehicle.
Children could open the driver's door and
unintentionally activate the EASY-ENTRY/ EXIT feature. This could result in an accident
and/or serious personal injury.
G
WARNING
Let the system complete the adjustment
procedure before setting the vehicle in
motion. All steering wheel adjustment must
be completed before setting the vehicle in
motion. Driving off with the steering wheel
still adjusting could cause the driver to lose
control of the vehicle.
! Do not activate the EASY-ENTRY/EXIT
feature, if

the seat backrest is reclined too
far backwards. This can damage the front
or rear seats. You must first move the
backrest to a vertical position.
Position of the steering wheel when the
EASY-ENTRY/EXIT feature is active The steering wheel moves upwards and
towards the dashboard if:
R
you remove

the SmartKey from the ignition
lock or
R you open the driver's door with the
SmartKey in position 0 or 1 in the ignition
lock.
i The steering wheel only moves upwards
and towards the dashboard if it has not
already reached the upper end stop.
Position of the steering wheel for
driving The steering wheel is moved to the last
selected position when:
R
the driver's door is closed.
R you insert the SmartKey into the ignition
lock
The last position of the steering wheel is
stored when you switch off the ignition or
when you store the setting with the memory
function ( Y page 85). Steering wheel
83
Seats, steering wheel and mirrors Z

Mirrors
Rear-view mirror
X Adjust the rear-view mirror by hand so you
have a good overview of the traffic
conditions. Exterior mirrors
Important safety notes G
WARNING
Exercise care when using the passenger-side
exterior rear view mirror. The mirror surface
is convex (outwardly curved surface for a
wider field of view). Objects in mirror are
closer than they appear. Check your interior
rear view mirror and glance over your
shoulder before changing lanes.
At low outside temperatures, the exterior
mirrors are heated automatically.
Adjusting the exterior mirrors The switches are located on the dashboard
on the left-hand side.
X
Make sure that the SmartKey is in position
1 or 2 in the ignition lock.
X Press button ;
for
the right-hand exterior
mirror or button = for the left-hand
exterior mirror.
X Press adjustment button : up, down, to
the right or to the left until the exterior mirror is set to a position that provides you
with a good overview of traffic conditions.
You will find further information in the
"Storing settings" section (

Y page 85).
Exterior mirror out of position If an exterior mirror has been pushed out of
position, proceed as follows:
X
Move the exterior mirror into the correct
position manually.
The mirror housing is engaged again and
you can

adjust the exterior mirrors as usual
(Y page 84). Automatic anti-glare mirrors
G
WARNING
The auto-dimming function does not react if
incoming light

is not aimed directly at sensors
in the interior rear view mirror.
The interior rear view mirror and the exterior
rear view mirror on the driver's side do not
react, for example, when transporting cargo
which covers the rear window.
Light hitting the mirror(s) at certain angles
(incident light) could blind you. As a result,
you may not be able to observe traffic
conditions and could cause an accident.
The rear-view mirror and the exterior mirror
on the driver's side automatically go into anti-
glare mode if the ignition is switched on and
incident light from headlamps strikes the
sensor in the rear-view mirror.
The mirrors do not go into anti-glare mode if
reverse gear is engaged or the interior lighting
is switched on. 84
Mirrors
Seats, steering wheel and mirrors

Useful information ..............................
88
Exterior lighting .................................. 88
Interior lighting ................................... 92
Replacing bulbs ................................... 94
Windshield wipers .............................. 99 87Lights and windshield wipers

Useful information
i This Operator's Manual describes all
models and all standard and optional
equipment of your vehicle available at the
time of publication of the Operator's
Manual. Country-specific differences are
possible. Please
note that your vehicle may
not be equipped with all features
described. This also applies to safety-
related systems and functions.
i Please read the information on qualified
specialist workshops (Y page 20). Exterior lighting
Important safety notes
For reasons of safety, Mercedes-Benz
recommends that you drive with the lights
switched on

even during the daytime. In some
countries, operation of the headlamps varies
due to legal requirements and self-imposed
obligations. In these countries, the daytime
running lamps are automatically switched on
when the engine is started. Information about driving abroad
To convert to symmetrical low beam
when driving

abroad: switch the headlamps
to symmetrical low beam in countries in
which traffic drives on the opposite side of the
road from the country where the vehicle is
registered. This prevents glare to oncoming
traffic. Symmetrical lights do not illuminate
as large an area of the edge of the road.
Have the headlamps converted at a qualified
specialist workshop as close to the border as
possible before driving in these countries.
To convert to asymmetrical low beam
after returning: have the headlamps
converted back to asymmetrical low beam at
a qualified specialist workshop as soon as
possible after crossing the border and
returning to the original country. Light switch
Operation 1
W
Left-hand standing lamps
2X Right-hand standing lamps
3$ Lights off/daytime running lamps
4Ã Automatic headlamp mode/daytime
running lamps
5T Parking lamps, side marker lamps,
license plate and instrument cluster
lighting
6L Low-beam/high-beam headlamps
7N Front fog lamps
8R Rear fog lamp
The turn signals, high-beam headlamps and
the high-beam

flasher are operated using the
combination switch (Y page 91).
! Switch off the standing lamps, parking
lamps and low-beam headlamps when you
leave the vehicle. This prevents the battery
from discharging.
The exterior lighting (except the parking
lamps) switches off automatically if you:
R remove the SmartKey from the ignition lock
R open the driver's door with the SmartKey
in position 0
If you hear a warning tone when you leave the
vehicle, the lights may still be switched on.
The Switch off lights message appears
in the multifunction display.
X Turn the light switch to $ or Ã.
X If you see the Switch off lights or
remove key message in the multifunction 88
Exterior lightingLights and windshield wipers

display, remove the SmartKey from the
ignition lock.
or
X Turn the light switch to $ or Ã.
Low-beam headlamps X
To switch on: turn the SmartKey to
position 2 in the ignition lock or start the
engine.
X Turn the light switch to L.
The L indicator lamp in the instrument
cluster lights up.
X To switch off: turn the light switch to
$.
Daytime running lamps Daytime running lamps in Canada
The "daytime running lamps" function is
required
by
law in Canada. It cannot therefore
be deactivated.
X Turn the light switch to $ or Ã.
When the engine is running: depending on
the ambient

light, the low-beam headlamps
or the parking lamps are switched on.
When the low-beam headlamps are
switched on, the L indicator lamp in the
instrument cluster lights up.
If the light switch is set to $
or Ã
, you
cannot activate the high-beam headlamps.
However, the high-beam flasher can always
be used. Turn the light switch to L when
driving at night. You can switch on the high-
beam headlamps in this position.
When the engine is running and the vehicle is
stationary: if you move the selector lever from
a driving position to N or P, the low-beam
headlamps go out after three minutes.
When the engine is running: if you turn the
light switch to T, you turn on the parking
lamps and low-beam headlamps.
When the engine is running: if you turn the
light switch to L, the manual settings take
precedence over the daytime running lamps. Daytime running lamps in the USA
In the USA, the daytime running lamps are
deactivated upon delivery from the factory.
X
To switch on: activate the daytime
running lamps function in the on-board
computer (Y page 160).
X Turn the light switch to $ or Ã.
When the engine is on: the low-beam
headlamps are switched on. The L
indicator lamp in the instrument cluster
lights up.
If the light switch is set to $
or Ã
, you
cannot switch on the high-beam headlamps
in bright conditions. Turn the light switch to
L. You can switch on the high-beam
headlamps in this position.
If the light switch is set to $, Ã or
L, you can switch on the high-beam
headlamps in less bright conditions.
However, the high-beam flasher can always
be used.
Turn the light switch to L when driving at
night.
When the engine is running: if you turn the
light switch to T or L, the manual
settings take precedence over the daytime
running lamps.
Automatic headlamp mode G
WARNING
If the exterior lamp switch is set to Ã, the
headlamps will not automatically come on
under foggy conditions.
To minimize

risk to you and to others, activate
headlamps by turning exterior lamp switch to
L when traffic and/or ambient lighting
conditions require you to do so.
In low ambient lighting conditions, only switch
from position à to L with the vehicle
at a standstill in a safe location. Switching
from à to L will briefly switch off the
headlamps. Doing so while driving in low
ambient lighting conditions may result in an
accident. Exterior lighting
89
Lights and windshield wipers
Z