2012 LINCOLN MKX warning

SETTING 911 ASSIST™ ON
Before setting this feature on, ensure that you read the911 Assist™
privacy noticelater in this section for important information.
1. Press
> SYNC Apps. > 911 Assist.
2. Select ON.
You can also access 911 Assist by:
•Pressing Menu > Settings> Phone > 911 Assist or
•Pressing Menu > Help > 911 Assist.
Note:SYNC911 Assist™ feature must be set on prior to the
incident.
To ensure that 911 Assist™ works properly:
•SYNCmust be powered and working properly at the time of the
incident and throughout feature activation and use.
•SYNC911 Assist™ feature must be set on prior to the incident.
•ABluetoothenabled and compatible phone has to be paired and
connected to SYNC.
•A connectedBluetoothenabled phone must have the ability to
make and maintain an outgoing call at the time of the incident.
•A connectedBluetoothenabled phone must have adequate
network coverage, battery power and signal strength.
•The vehicle must have battery power and be located in the U.S.,
Canada or in a territory in which 911 is the emergency number.
WARNING:Unless the 911 Assist™ setting is set on prior to a
crash, the system won’t dial for help which could delay response
time, potentially increasing the risk of serious injury or death after a
crash.
WARNING:Don’t wait for 911 Assist™ to make an emergency
call if you can do it yourself. Dial emergency services
immediately to avoid delayed response time which could increase the
risk of serious injury or death after a crash. If you don’t hear 911
Assist™ within five seconds of the crash, the system or phone may be
damaged or non-functional.
Information features
52
2012 HMI-1 Gen 2(fd1)
Supplement, 1st Printing
USA(fus)

IN THE EVENT OF A CRASH
Not all crashes deploy an airbag or activate the fuel pump shut-off
(which would activate 911 Assist™); however, if 911 Assist™ is
triggered, SYNCwill try to contact emergency services. If a connected
phone is damaged or loses connection to SYNC, SYNCwill search for,
and try to connect to, any available previously paired phone and try to
make the call to 911.
Before making the call:
•SYNCprovides a short window of time (about 10 seconds) to
cancel the call. Failure to cancel the call will result in SYNC
attempting to dial 911.
•SYNCwill say the following, or a similar message: “SYNCwill
attempt to call 911, to cancel the call, press Cancel on your screen
or press and hold the phone button on your steering wheel.”
If the call is not cancelled and a successful call is made, a prerecorded
message will be played for the 911 operator, then the occupant(s) in the
vehicle will be able to talk with the operator. Be prepared to provide
your name, phone number and location immediately, because not all 911
systems are capable of receiving this information electronically.
911 Assist™ may not work if:
•Your cell phone or 911 Assist™ hardware was damaged in a crash.
•The vehicle’s battery or SYNC system has no power.
•The phone(s) paired and connected to the system was thrown
from the vehicle.
•Note:Every phone operates differently. While SYNC911 Assist™
works with most cell phones, some may have trouble using this
feature.
WARNING:Always place your phone in a secure location in the
vehicle so it doesn’t becoming a projectile or get damaged in a
collision. Failure to do so may cause serious injury to someone or
damage the phone which could prevent 911 Assist™ from working
properly.
Information features
53
2012 HMI-1 Gen 2(fd1)
Supplement, 1st Printing
USA(fus)

911 ASSIST™ PRIVACY NOTICE
Once 911 Assist™ is set on, it may disclose to emergency services that
the vehicle has been in a crash involving the deployment of an airbag or
activation of the fuel pump shut-off. Certain versions or updates to 911
Assist™ may also be capable of electronically or verbally disclosing to
911 operators the vehicle location, and/or other details about the vehicle
or crash to assist 911 operators to provide the most appropriate
emergency services. If you do not want to disclose this information, do
not turn the feature on.
Note:If 911 Assist™ is turned on or off by any user, that setting will
apply for all paired phones. If 911 Assist™ is turned off, a voice message
will play and/or a display message/icon will come on when the vehicle is
started after a previously paired phone connects.
Vehicle Health Report (if equipped, U.S. only)
Check your vehicle’s overall “health” in the form of diagnostic report
card. See:
•Vehicle diagnostic information
•Suggested scheduled maintenance
•Open recalls and field service actions
•Items from a prior vehicle inspection that need your attention
Note:You’ll need to register your vehicle at www.syncmyride.com before
using this feature. There are no fees or subscription requirements, but
youmustregister to use this feature.
Note:In order to allow a break-in period for your vehicle, you may not
be able to create a Vehicle Health Report until your vehicle odometer has
reached 200 miles.
WARNING:Vehicle Health Report only monitors certain systems
that are electronically monitored by the vehicle and will not
monitor or report the status of any other system, (i.e., brake lining
wear). Failure to perform scheduled maintenance and regularly inspect
your vehicle may result in vehicle damage and serious injury.
Information features
54
2012 HMI-1 Gen 2(fd1)
Supplement, 1st Printing
USA(fus)

•THERE ARE NO WARRANTIES OTHER THAN THOSE THAT MAY
EXPRESSLY BE PROVIDED FOR YOUR NEW VEHICLE.
End user notice
MicrosoftWindowsMobile for Automotive Important Safety
Information
This system Ford SYNC™ contains software that is licensed to
Manufacturer FORD MOTOR COMPANY by an affiliate of Microsoft
Corporation pursuant to a license agreement. Any removal, reproduction,
reverse engineering or other unauthorized use of the software from this
system in violation of the license agreement is strictly prohibited and
may subject you to legal action.
Read and follow instructions
Before using your Windows Automotive-based system, read and follow all
instructions and safety information provided in this end user manual
(“User’s Guide”). Not following precautions found in this User’s Guide
can lead to an accident or other serious consequences.
Keep User’s Guide in Vehicle
When kept in the vehicle, the User’s Guide will be a ready reference for
you and other users unfamiliar with the Windows Automotive-based
system. Please make certain that before using the system for the first
time, all persons have access to the User’s Guide and read its
instructions and safety information carefully.
WARNING:Operating certain parts of this system while driving
can distract your attention away from the road, and possibly
cause an accident or other serious consequences. Do not change
system settings or enter data non-verbally (using your hands) while
driving. Stop the vehicle in a safe and legal manner before attempting
these operations. This is important since while setting up or changing
some functions you might be required to distract your attention away
from the road and remove your hands from the wheel.
General operation
Voice Command Control
Functions within the Windows Automotive-based system may be
accomplished using only voice commands. Using voice commands while
driving allows you to operate the system without removing your hands
from the wheel.
End User License Agreements
89
2012 HMI-1 Gen 2(fd1)
Supplement, 1st Printing
USA(fus)

PARTICULAR PURPOSE, TITLE, AND NON-INFRINGEMENT. NEITHER
GRACENOTE WARRANTS THE RESULTS THAT WILL BE OBTAINED
BY YOUR USE OF THE GRACENOTE SOFTWARE OR ANY
GRACENOTE SERVER. IN NO CASE WILL GRACENOTE BE LIABLE
FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES OR FOR ANY
LOST PROFITS OR LOST REVENUES FOR ANY REASON
WHATSOEVER.
Gracenote 2007
FCC ID: KMHSYNCG2 IC: 1422A-SYNCG2
FCC ID: KMHSYNCG2-L IC: 1422A-SYNCG2L
This device complies with Part 15 of the FCC Rules and with RSS-210 of
Industry Canada. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may
cause undesired operation.
WARNING:Changes or modifications not expressively approved
by the party responsible for compliance could void the user’s
authority to operate the equipment. The term “IC:” before the radio
certification number only signifies that Industry Canada technical
specifications were met.
The antenna used for this transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.
End User License Agreements
100
2012 HMI-1 Gen 2(fd1)
Supplement, 1st Printing
USA(fus)