2012 LINCOLN MKX My Lincoln Touch Manual

ACCESSING AND ADJUSTING MODES THROUGH YOUR
INFOTAINMENT DISPLAY (IF EQUIPPED)
Your vehicle may have an infotainment display located on the right side
of your instrument cluster. The display allows you to view and make
minor adjustments to your active modes without taking your hands off
the wheel. For example:
•In phone mode, you can accept or reject an incoming call.
•In Entertainment mode, you can view what is playing and make some
adjustments.
•You can also access and make adjustments in Navigation mode (if
equipped) and Climate mode.
Use the OK and arrow buttons on
the right side of your steering wheel
to scroll through your available
modes:
•
Entertainment
•
Phone
•
Navigation (if equipped)
•
Climate
Note:If your vehicle is not equipped with navigation,Compasswill
appear in the display instead ofNavigation. If you press
to go into
theCompassmenu, you can see the compass graphic.
•Press
/to scroll through the modes.
km/h
80
60
40
20
0
20
0 40 60 80
100120140160180
200
220
100120140
MPH
Instrument cluster
9
2012 HMI-1 Gen 2(fd1)
Supplement, 1st Printing
USA(fus)

•Pressto enter the mode.
•Press
/to make adjustments within the chosen mode.
•Press OK to confirm your selection.
For information on the message center displayon the left hand side
of your cluster, refer to theInstrument Clusterchapter in your Owner’s
Guide.
Instrument cluster
10
2012 HMI-1 Gen 2(fd1)
Supplement, 1st Printing
USA(fus)

VOICE RECOGNITION FEATURE
Your system is equipped with an advanced interactive voice recognition
(VR) system. This system allows you to perform many operations by
speaking certain commands to the system. The system will respond with
a series of audible tones, questions and spoken confirmations depending
on the situation and the chosen level of dialogue interaction.
System feedback and interaction
Your voice recognition system provides feedback via audible tones when:
•You are entering a new voice session
•A voice session is successful or unsuccessful
•A speed dependent feature is accessed
•The system is ready to listen for a command
•You choose to access the Help feature
•The system gives a positive or negative recognition
The system will also ask short questions (confirmation prompts) when it
has not clearly understood your request or when there are several
possible responses to your request.
Voice recognition visual feedback
When using voice commands, the following icons and words may appear
in the lower left status bar indicating the voice session status:
•
Listening•Paused
•
Success•?Try Again
•
Failed
Voice settings
Voice settings allow you to customize the level of system interaction,
help and feedback. The system defaults to standard interaction which
uses candidate lists and confirmation prompts as these provide the
highest level of guidance and feedback. To access these settings, you can
either:
1. Press Menu > Settings > Voice control.
Voice recognition system overview
11
2012 HMI-1 Gen 2(fd1)
Supplement, 1st Printing
USA(fus)

2. Select from the following:
•Interaction Mode•Confirmation Prompts
•Media Candidate Lists•Phone Candidate Lists
•Voice Control Volume
Or
1. Press
on the steering wheel controls. A tone will sound followed
by the prompt, “Please say a command”. Another tone will sound to
signify the system is listening.
2. Say one of the following commands:
•Interaction Mode Advanced•Interation Mode Novice
•Confirmation Prompts On•Confirmation Prompts Off
•Phone Candidate Lists On•Phone Candidate Lists Off
•Media Candidate Lists On•Media Candidate Lists Off
Interaction Mode:Novice interaction mode provides more detailed
interaction and guidance while the advanced mode has less audible
interaction and more tone prompts.
Confirmation Prompts:Confirmation prompts are short questions
asked by the system when the system has not clearly heard or
understood your request.Note:Even with confirmation prompts turned
off, you may be asked to confirm settings occasionally and number
inputs.
Phone/Media Candidate Lists:Candidate lists are a list of possible
results from your voice commands. These occur when SYNChas equal
confidence of several possible results from your voice command.
How to use voice commands with your system
1. Press
on the steering wheel controls.
Depending on the feedback setting, you will either hear, “Please say a
command” followed by a tone or just the tone, signaling the system is
ready to accept your command.
2. After the tone, speak the command clearly.
For best voice recognition performance
•Ensure that the interior of the vehicle is as quiet as possible.
•Speak naturally without long pauses between words.
•After pressing
, wait for the tone to sound and for ‘Listening’ to
appear in the display. Any command spoken prior to this will not
register with the system.
Voice recognition system overview
12
2012 HMI-1 Gen 2(fd1)
Supplement, 1st Printing
USA(fus)

•You can interrupt the system at any time while it is speaking by
pressing
. The system will respond with a tone and allow you to
speak your command.
What can I say?
To access the available voice commands for the current session, do one
of the following:
•During a voice session, press the
icon at the bottom of the screen.
•Say “What Can I Say??” for an on screen listing of the possible voice
commands that are associated with your current voice session.
•Press
on the steering wheel controls and after the tone say “Help”
for an audible list of possible voice commands.
To access a list of available voice commands
•Press Menu > Help > Voice command list
OR
•Press
on the steering wheel controls and when prompted, say any
of the following (if available):
•List of Commands•Phone List of Commands
•Radio List of Commands•Climate Control List of
Commands
•Navigation List of Commands•Travel Link List of Commands
•Sirius Satellite List of Commands•Audio List of Commands
•USB List of Commands•SD Card List of Commands
•Bluetooth Audio List of
Commands•Browse List of Commands
Global voice commands
The following voice commands can be spoken at any time during a voice
session:
•Help•What Can I Say?
•Main Menu•Go Back
•Next Page•Previous Page
•Exit•List of Commands
Voice recognition system overview
13
2012 HMI-1 Gen 2(fd1)
Supplement, 1st Printing
USA(fus)

Using voice commands with the touchscreen options
Your voice system has a special dual mode feature which allows you to
switch between using voice commands and the touchscreen. The most
common place this is available is with your navigation feature (if
equipped). During a navigation voice session, you will notice that some
of the buttons on the screen are outlined in blue and some are not.
The buttons on the screen that are outlined in blue are both voice
commands and can be selected during a voice session. The buttons that
are not outlined in blue can’t be used as voice commands and if they are
touched during a voice session will cancel the voice session. Some
examples are as follows:
•If you press
and say, “Navigation”, after the system confirms the
command and prompts you again, say, “Destination”. The system will
change to the destination screen.
•If you say, “Intersection”, then the system will change the screen to
the intersection screen where “Street”, “City” and “State” are outlined
in blue. You are able to switch between fields by touching the buttons
or by saying, “Enter first street” or “Change city”.
•If you say, “Street Address” the screen will change to the street
address screen and then “Enter City”, where State, City, Street and
Number are outlined in blue indicating that you are able to switch
between the fields by touching the buttons or by saying commands
like “Enter Street”, “Change City”, or “Enter House Number”.
•If you are in the process of entering a destination by voice and your
vehicle comes to a stop, (for example, stopping at a red light), the key
board will appear on the screen. If you make more than three
consecutive button presses, (for example, spelling a city), then the
voice session will be cancelled.
Voice recognition system overview
14
2012 HMI-1 Gen 2(fd1)
Supplement, 1st Printing
USA(fus)

LISTENING TO MUSIC
Your system offers many media options. You can access these options via
the touchscreen or voice commands.
Browse voice commands
When listening to any type of audio, you can browse through other
devices without having to change sources. For example, if you are
currently listening to the radio, you can browse all the artists that are
stored on your USB device.
Press
on the steering wheel controls and when prompted, you can
say:
•Browse Station List•Browse AM Station List
•Browse FM Station List•Browse SIRIUS Channel Guide
•Browse Channels•Browse Games
•Browse CD Track List•Browse USB
•Browse SD Card•Browse Bluetooth Audio
•Browse*
*Note:If you have said, “Browse”, you can then say any of the following
commands:
•AM Station List•FM Station List
•SIRIUS Channel Guide•CD Track List
• Games•USB
•SD Card•Bluetooth Audio
AM/FM SIRIUS CD USB BT
Stereo SD
CardAV
In
Media features
15
2012 HMI-1 Gen 2(fd1)
Supplement, 1st Printing
USA(fus)

For a complete list of Browse voice commands, refer toVoice
commands for your USB and SD CardandVoice commands for
Bluetooth Audioin the following sections.
AM/FM RADIO
Press the lower left corner of the touchscreen and then select the
AM/FM tab.
To change between AM and FM, repeatedly press the AM/FM tab.
To change between AM1/AM AST or the FM/FM1/FM2/FM AST presets,
repeatedly press the lower left corner of the touchscreen.
From the main screen, you can:
•Save a station by tuning to the station and then pressing and
holding one of the memory preset areas (on the right side of the
screen). You will hear a brief mute and the sound will return when
the station is saved.
•Press ‘Direct Tune’ and enter the desired station number when
prompted. Then press ‘Enter’.
•Select ‘Browse’ to view a list of all available stations. Scroll and
select the desired station.
•Press the HD Radio button to activate HD Radiotechnology. This
feature enables you to receive radio broadcasts digitally, (where
available), providing free, crystal clear sound. Refer to theHD
Radioinformationin the following section.
•Press ‘Options’ to access:
Sound Settings:Select to adjust Bass, Treble, Midrange, Balance
and Fade, THX Deep note demo (if equipped), DSP (if equipped),
Occupancy mode (if equipped), and Speed compensated volume
settings.
Set PTY for Seek/Scan:Select a category of music you would like
to search for and then choose to either seek or scan for the
stations.
RDS Text Display On/Off:Select On to always view the
information broadcast by FM stations.
Auto Presets (AST)- Autostore:Select to have the system
automatically store the six strongest stations in your current
location. These will not override any presets stored in any of the
AM or FM frequency bands.
Media features
16
2012 HMI-1 Gen 2(fd1)
Supplement, 1st Printing
USA(fus)