2012 Lexus GS350 ignition

6566-3. Do-it-yourself maintenance
GS350/250_EE (OM30C36E)
CAUTION
When working near the electric cooling fans or radiator grille
Be sure the engine switch is off.
With the engine switch in IGNITION ON mode, the electric cooling fans
may automatically start to run if the air conditioning is on and/or the cool-
ant temperature is high. (P. 667)
Safety glasses
Wear safety glasses to prevent flying or falling material, fluid spray, etc.
from getting in your eyes.
NOTICE
If you remove the air cleaner filter
Driving with the air cleaner filter removed may cause excessive engine
wear due to dirt in the air. Also, a backfire could cause a fire in the engine
compartment.
If the fluid level is low or high
It is normal for the brake fluid level to go down slightly as the brake pads
wear or when the fluid level in the accumulator is high.
If the reservoir needs frequent refilling, it may indicate a serious problem.

675 6-3. Do-it-yourself maintenance
6
Maintenance and care
GS350/250_EE (OM30C36E)
Initializing the tire pressure warning system
The tire pressure warning system must be initialized in the fol-
lowing circumstances:
When rotating the tires.
When the tire inflation pressure is changed such as when
changing traveling speed.
When the tire pressure warning system is initialized, the current
tire inflation pressure is set as the benchmark pressure.
How to initialize the tire pressure warning system
Park the vehicle in a safe place and turn the engine switch off.
Initialization cannot be performed while the vehicle is moving.
Adjust the tire inflation pressure to the specified cold tire infla-
tion pressure level. (P. 850)
Make sure to adjust the tire pressure to the specified cold tire inflation
pressure level. The tire pressure warning system will operate based on
this pressure level.
Turn the engine switch to IGNITION ON mode.
1
2
3

6766-3. Do-it-yourself maintenance
GS350/250_EE (OM30C36E)Press and hold the tire pres-
sure warning reset switch
until the tire pressure warn-
ing light blinks slowly 3
times.
Wait for a few minutes with the engine switch in IGNITION
ON mode and then turn the engine switch off.
Registering ID codes
The tire pressure warning valve and transmitter is equipped with
a unique ID code. When replacing a tire pressure warning valve
and transmitter, it is necessary to register the ID code. Have the
ID code registered by any authorized Lexus dealer or repairer, or
another duly qualified and equipped professional.
4
5

677 6-3. Do-it-yourself maintenance
6
Maintenance and care
GS350/250_EE (OM30C36E)
When to replace your vehicle’s tires
Tires should be replaced if:
You have tire damage such as cuts, splits, cracks deep enough to expose the
fabric, and bulges indicating internal damage
A tire goes flat repeatedly or cannot be properly repaired due to the size or
location of a cut or other damage
If you are not sure, consult with any authorized Lexus dealer or repairer, or
another duly qualified and equipped professional.
Replacing tires and wheels (vehicles with the tire pressure warning system)
If the ID code of the tire pressure warning valve and transmitter is not regis-
tered, the tire pressure warning system will not work properly. After driving
for about 10 minutes, the tire pressure warning light blinks for 1 minute and
stays on to indicate a system malfunction.
Tire life
Any tire over 6 years old must be checked by a qualified technician even if it
has seldom or never been used or damage is not obvious.
Routine tire inflation pressure checks
The tire pressure warning system does not replace routine tire inflation pres-
sure checks. Make sure to check tire inflation pressure as part of your routine
of daily vehicle checks.
When rotating the tires (vehicles with the tire pressure warning system featur-
ing a tire inflation pressure display function)
Make sure that the engine switch is off. If the tires are rotated while the
engine switch is in IGNITION ON mode, the tire position information will
not be updated.
If this accidentally occurs, either turn the engine switch to off and then to
IGNITION ON mode, or initialize the system after checking that the tire
pressure is properly adjusted.

6806-3. Do-it-yourself maintenance
GS350/250_EE (OM30C36E)
The initialization operation (vehicles with the tire pressure warning system)
Make sure to carry out initialization after adjusting the tire inflation pres-
sure.
Also, make sure the tires are cold before carrying out initialization or tire
inflation pressure adjustment.
If you have accidentally turned the engine switch off during initialization, it
is not necessary to press the reset switch again as initialization will restart
automatically when the engine switch has been turned to IGNITION ON
mode for the next time.
If you accidentally press the reset switch when initialization is not neces-
sary, adjust the tire inflation pressure to the specified level when the tires
are cold, and conduct initialization again.
Warning performance of the tire pressure warning system (if equipped)
The warning of the tire pressure warning system will change in accordance
with the conditions under which it was initialized. For this reason, the system
may give a warning even if the tire pressure does not reach a low enough
level, or if the pressure is higher than the pressure that was adjusted to when
the system was initialized.
When initialization of the tire pressure warning system has failed (vehicles
with the tire pressure warning system)
Initialization can be completed in a few minutes. However, in the following
cases, the settings have not been recorded and the system will not operate
properly. If repeated attempts to record tire inflation pressure settings are
unsuccessful, have the vehicle inspected by any authorized Lexus dealer or
repairer, or another duly qualified and equipped professional.
When operating the tire pressure warning reset switch, the tire pressure
warning light does not blink 3 times.
After carrying out the initialization procedure, the tire pressure warning
light blinks for 1 minute then stays on after driving for 10 minutes.

7457-2. Steps to take in an emergency
7
When trouble arises
GS350/250_EE (OM30C36E)
Before emergency towing
Release the parking brake.
Shift the shift lever to N.
Turn the engine switch to ACCESSORY (engine off) or IGNITION ON
(engine running) mode.
CAUTION
Observe the following precautions.
Failure to do so may result in death or serious injury.
Caution while towing
Use extreme caution when towing the vehicle.
Avoid sudden starts or erratic driving maneuvers which place excessive
stress on the emergency towing eyelets and the cables or chains. Always
be cautious of the surroundings and other vehicles while towing.
If the engine is not running, the power assist for the brakes and steering
will not function, making steering and braking more difficult.
Installing towing eyelets to the vehicle
Make sure that towing eyelets are installed securely.
If not securely installed, towing eyelets may come loose during towing.
1
2
3

7557-2. Steps to take in an emergency
7
When trouble arises
GS350/250_EE (OM30C36E)
When a tire is replaced with a spare tire
Vehicles with a compact spare tire: The compact spare tire is not equipped
with a tire pressure warning valve and transmitter. If a tire goes flat, the tire
pressure warning light will not turn off even though the flat tire has been
replaced with the spare tire.
Vehicles with a full-size spare tire: The spare tire is also equipped with a tire
pressure warning valve and transmitter. The tire pressure warning light will
turn on if the tire inflation pressure of the spare tire is low. If a tire goes flat,
the tire pressure warning light will not turn off even though the flat tire has
been replaced with the spare tire.
Conditions that the tire pressure warning system may not function properly
P. 6 7 8
If the tire pressure warning light frequently comes on after blinking for 1 min-
ute
If the tire pressure warning light frequently comes on after blinking for 1
minute when the engine switch is turned to IGNITION ON mode, have it
checked by any authorized Lexus dealer or repairer, or another duly qualified
and equipped professional.
Warning buzzer
In some cases, the buzzer may not be heard because of noisy place or an
audio sound.

8237-2. Steps to take in an emergency
7
When trouble arises
GS350/250_EE (OM30C36E)
Trunk
Turn the mechanical key
clockwise to open.
Ensure that the shift lever is in P and depress the brake pedal.
Touch the Lexus emblem side
of the electronic key to the
engine switch.
The engine switch will turn to
IGNITION ON mode.
When the smart entry & start sys-
tem is deactivated in customization
setting, the engine switch will turn
to ACCESSORY mode.
Firmly depress the brake pedal and check that is shown on
the multi-information display.
Press the engine switch.
In the event that the engine still cannot be started, contact any
authorized Lexus dealer or repairer, or another duly qualified and
equipped professional.
Starting the engine
1
2
3
4