2012 Lexus GS350 Owner's Manual

1663-3. Adjusting the seats
GS350/250_EE (OM30C36E)The auto away/return function
enables easy access by activating
when the driver or front passen-
ger attempts to enter or exit the
vehicle.
Auto away function when exiting the vehicle (driver’s/front pas-
senger’s seat)
Driver’s seat
When all of the following actions have been performed, the
steering wheel will move up and back to the point farthest away
from the driver and the seat will move backward:
• The shift lever has been shifted to P.
• The engine switch has been turned off.
• The driver’s seat belt has been unfastened.
Front passenger’s seat (if equipped)
If the lumbar support, calf support (if equipped), etc. of the front
passenger’s seat has been adjusted, the seat will return to its orig-
inal state if the front passenger’s door is opened while the vehicle
is stopped to allow easy exit from the vehicle.
Auto return function when entering the vehicle (driver’s seat
only)
When either of the following actions has been performed, the
steering wheel will move toward the driver and seat will move
forward:
• The engine switch has been turned to ACCESSORY mode.
• The driver’s seat belt has been fastened.
Power easy access system

167
3 3-3. Adjusting the seats
Operation of each component
GS350/250_EE (OM30C36E)
When driving position memory is linked with door unlock operation
If the driver’s door is opened, the driver’s seat will move toward the memo-
rized position but stop slightly beforehand to allow easy access to the vehi-
cle.
Turning the engine switch to ACCESSORY or IGNITION ON mode, or fas-
tening the driver’s seat belt moves the seat fully into the memorized position.
Operating the driving position memory after turning the engine switch off
Driver’s seat:
Memorized seat positions can be activated up to 180 seconds after the
driver’s door is opened and another 60 seconds after it is closed again. Mem-
orized steering wheel position can be activated by pressing the engine switch.
Front passenger’s seat:
Memorized positions can be activated up to 180 seconds after the front pas-
senger’s door is opened by pressing button “1”, “2” or “3”.
Correct seat position
When the seat is in the most forward or most backward position, and the seat
is being moved in those directions, the system may not correctly recognize
the current position and the memorized position will not be correctly
recalled.
The auto away function for exiting the driver’s seat
If the seat is already close to the rearmost position, the auto away function
may not operate when the driver exits the vehicle.
Customization
The distance that the driver’s seat moves backward during the auto away
function can be changed. (Customizable features: P. 855)
CAUTION
Seat adjustment caution
Take care during seat adjustment so that the seat does not strike the rear
passenger or squeeze your body against the steering wheel.

1683-3. Adjusting the seats
GS350/250_EE (OM30C36E)
Head restraints
Vertical adjustment
Up
Pull the head restraints up.
Down
Push the head restraint down while
pressing the lock release button.
Head restraints are provided for all seats.
Front seats
Lock release but-
1
2
Angle adjustment (if
equipped)Side support adjustment
(if equipped)
The position of the head restraint
can be adjusted forward in 4
stages.
If the head restraint is pulled for-
ward from the foremost position, it
will return to the rearmost posi-
tion.

1693-3. Adjusting the seats
3
Operation of each component
GS350/250_EE (OM30C36E)Up
Pull the head restraints up.
Down
Push the head restraint down while
pressing the lock release button.
Removing the head restraints
Installing the head restraints
Front seats
Rear seats
Rear seats
Lock release but-
1
2
Pull the head restraint up while pressing
the lock release button.
Align the head restraint with the installa-
tion holes and push it down to the lock
position.
Press and hold the lock release button
when lowering the head restraint.
Align the head restraint with the installa-
tion holes and push it down to the lowest
lock position while pressing the lock
release button.
Lock release but-
Lock release but-
Lock release but-

1703-3. Adjusting the seats
GS350/250_EE (OM30C36E)
Adjusting the height of the head restraints
Adjusting the rear seat head restraint
Always raise the head restraint one level from the stowed position when
using. Make sure that the head restraints are
adjusted so that the center of the head
restraint is closest to the top of your ears.
CAUTION
Head restraint precautions
Observe the following precautions regarding the head restraints. Failure to
do so may result in death or serious injury.
Use the head restraints designed for each respective seat.
Adjust the head restraints to the correct position at all times.
After adjusting the head restraints, push down on them and make sure
they are locked in position.
Do not drive with the head restraints removed.

1703-4. Adjusting the steering wheel and mirrors
GS350/250_EE (OM30C36E)
Steering wheel
Operating the switch moves the steering wheel in the following
directions:
Up
Down
Toward the driver
Away from the driver
The steering wheel can be adjusted when
The engine switch is in ACCESSORY or IGNITION ON mode
*.
*: If the driver’s seat belt is fastened, the steering wheel can be adjusted
regardless of engine switch mode.
Automatic adjustment of the steering position
A desired steering position can be entered to memory and recalled automati-
cally by the driving position memory system. (P. 162)
Power easy access system
The steering wheel and driver’s seat move in accordance with engine switch
mode and the driver’s seat belt condition. (P. 166)
Adjustment procedure
1
2
3
4
CAUTION
Do not adjust the steering wheel while driving.
Doing so may cause the driver to mishandle the vehicle and cause an acci-
dent, resulting in death or serious injury.

171
3 3-4. Adjusting the steering wheel and mirrors
Operation of each component
GS350/250_EE (OM30C36E)
Inside rear view mirror
The height of the rear view mirror can be adjusted to suit your driv-
ing posture.
Adjust the height of the rear
view mirror by moving it up and
down.
Manual anti-glare inside rear view mirror
Reflected light from the headlights of vehicles behind can be
reduced by operating the lever.
Normal position
Anti-glare position
The rear view mirror’s position can be adjusted to enable sufficient
confirmation of the rear view.
Adjusting the height of rear view mirror
Anti-glare function
1
2

1723-4. Adjusting the steering wheel and mirrors
GS350/250_EE (OM30C36E)
Auto anti-glare inside rear view mirror
Responding to the level of brightness of the headlights of vehicles
behind, the reflected light is automatically reduced.
Changing automatic anti-glare
function mode
ON/OFF
When the automatic anti-glare
function is in ON mode, the indi-
cator illuminates.
The function will set to ON mode
each time the engine switch is
turned to IGNITION ON mode.
Pressing the button turns the func-
tion to OFF mode. (The indicator
also turns off.)
To prevent sensor error (vehicles with auto anti-glare inside rear view mirror)
Indicator
To ensure that the sensors operate prop-
erly, do not touch or cover them.