2012 Lancia Flavia tow

FLASH LIGHTS WITH
LOCK
The feature will cause the turn signal
lights to flash when the doors are
locked or unlocked with the RKE
transmitter. This feature can be
turned on or turned off.
Refer to “Electronic Vehicle Informa-
tion Center (EVIC)/Personal Settings
(Customer-Programmable Fea-
tures)” in “Understanding Your In-
strument Panel” for further informa-
tion.
PROGRAMMING
ADDITIONAL
TRANSMITTERS
Refer to Sentry Key® “Customer Key
Programming.”
If you do not have a programmed
RKE transmitter, contact your autho-
rized dealer for details.GENERAL INFORMATION
Transmitter and receivers operate on
a carrier frequency of 433.92 MHz.
Operation is subject to the following
conditions:
1. This device may not cause harmful
interference.
2. This device must accept any inter-
ference that may be received includ-
ing interference that may cause unde-
sired operation.
NOTE:
Changes or modifications not ex-
pressly approved by the party re-
sponsible for compliance could
void the user's authority to operate
the equipment.
If your RKE transmitter fails to oper-
ate from a normal distance, check for
these two conditions:
1. Weak battery in transmitter. The
expected life of a battery is five years.
2. Closeness to a radio transmitter
such as a radio station tower, airport
transmitter, military base, and some
mobile or CB radios.BATTERY REPLACEMENT
The recommended replacement bat-
tery is CR2032.
1. With the RKE transmitter buttons
facing down, use a flat blade to pry
the two halves of the RKE transmitter
apart. Make sure not to damage the
seal during removal.
2. Remove and replace the battery.
Avoid touching the new battery with
your fingers. Skin oils may cause bat-
tery deterioration. If you touch a bat-
tery, clean it with rubbing alcohol.
3. To assemble the RKE transmitter
case, snap the two halves together.
Separating RKE Transmitter Halves
17

WARNING!(Continued)
 A shoulder belt placed behind you
will not protect you from injury
during a collision. You are more
likely to hit your head in a colli-
sion if you do not wear your shoul-
der belt. The lap and shoulder belt
are meant to be used together.
4. Position the lap belt across your
thighs, below your abdomen. To re-
move slack in the lap belt portion, pull
up on the shoulder belt. To loosen the
lap belt if it is too tight, lift up on the
shoulder belt and pull on the lap belt.
A snug belt reduces the risk of sliding
under the belt in a collision.
WARNING!
 A lap belt worn too high can in- crease the risk of internal injury in
a collision. The belt forces won't
be at the strong hip and pelvic
bones, but across your abdomen.
Always wear the lap belt as low as
possible and keep it snug.
 A twisted belt may not protect you
properly. In a collision, it could
even cut into you. Be sure the belt
is straight. If you can't straighten
a belt in your vehicle, take it to
your authorized dealer immedi-
ately and have it fixed.
5. Position the shoulder belt on your
chest so that it is comfortable and not
resting on your neck. The retractor
will withdraw any slack in the belt.
6. To release the belt, push the red
button on the buckle. The belt will
automatically retract to its stowed po-
sition. If necessary, slide the latch
plate down the webbing to allow the
belt to retract fully.
WARNING!
A frayed or torn belt could rip apart
in a collision and leave you with no
protection. Inspect the belt system
periodically, checking for cuts,
frays, or loose parts. Damaged parts
must be replaced immediately. Do
not disassemble or modify the sys-
tem. Seat belt assemblies must be
replaced after a collision if they have
been damaged (i.e., bent retractor,
torn webbing, etc.).
LAP/SHOULDER BELT
UNTWISTING PROCEDURE
Use the following procedure to un-
twist a twisted lap/shoulder belt.
1. Position the latch plate as close as
possible to the anchor point.
2.
At about 15 to 30 cm above the
latch plate, grasp and twist the belt
webbing 180° to create a fold that be-
gins immediately above the latch plate.
3. Slide the latch plate upward over
the folded webbing. The folded web-
bing must enter the slot at the top of
the latch plate.
4. Continue to slide the latch plate up
until it clears the folded webbing.
Inserting Latch Plate Into Buckle
25

ments. Regardless of the specific type
of lower attachment, never install
ISOFIX-compatible child seats such
that two seats share a common lower
anchorage. If you are installing
ISOFIX-compatible child restraints in
adjacent rear seating positions, you
can use the ISOFIX anchors or the
vehicle's seat belts. If your child re-
straints are not ISOFIX-compatible,
you can only install the child re-
straints using the vehicle's seat belts.
For typical installation instructions,
refer to “Installing The ISOFIX-
Compatible Child Restraint System”.
Rear Seat ISOFIX Anchors
Child restraints systems having at-
tachments designed to connect to the
lower anchorages are now available.
Child restraints having tether straps
and hooks for connection to the top
tether anchorage, have been available
for some time. In fact, many child
restraint manufacturers will provide
add-on tether strap kits for some of
their older products.Because the lower anchorages are to
be introduced to passenger carrying
vehicles over a period of years, child
restraint systems having attachments
for those anchorages will continue to
have features for installation in ve-
hicles using the lap or lap/shoulder
belt. They will also have tether straps,
and you are urged to take advantage
of all of the available attachments
provided with your child restraint in
any vehicle.
NOTE:
When using the ISOFIX attaching
system to install a child restraint,
please ensure that all seat belts not
being used for occupant restraints
are stowed and out of reach of chil-
dren. It is recommended that be-
fore installing the child restraint,buckle the seat belt so the seat belt
is tucked behind the child re-
straint and out of reach. If the
buckled seat belt interferes with
the child restraint installation, in-
stead of tucking the seat belt be-
hind the child restraint, route the
seat belt through the child re-
straint belt path and then buckle
it. This should stow the seat belt
out of the reach of an inquisitive
child. Remind all children in the
vehicle that the seat belts are not
toys and should not be played
with, and never leave your child
unattended in the vehicle.
Installing The ISOFIX-
Compatible Child Restraint
System
We urge you to carefully follow the
directions of the manufacturer when
installing your child restraint. Not all
child restraint systems will be in-
stalled as described here. Again, care-
fully follow the installation instruc-
tions that were provided with the
child restraint system.
Rear Seat ISOFIX Anchors
41

The rear seat lower anchor-
ages are round bars, located
at the rear of the seat cush-
ion where it meets the seat-
back, and are just visible when you
lean into the rear seat to install the
child restraint. You will easily feel
them if you run your finger along the
intersection of the seatback and seat
cushion surfaces.
In addition, there are tether
strap anchorages behind
each rear seating position.
Access ports to the tether
anchors are located in the panel be-
tween the rear seat and the rear win-
dow. The tether anchors are under-
neath access covers in the carpet
covering the back of the seat where
you see this symbol.
Many, but not all, restraint systems
will be equipped with separate straps
on each side, with each having a hook
or connector for attachment to the
lower anchorage and a means of ad-
justing the tension in the strap.
Forward-facing toddler restraints and
some rear-facing infant restraints will
also be equipped with a tether strap, a hook for attachment to the tether
strap anchorage and a means of ad-
justing the tension of the strap.
You will first loosen the child seat
adjusters on the lower straps and on
the tether strap so that you can more
easily attach the hooks or connectors
to the vehicle anchorages. Next, at-
tach the lower hooks or connectors
over the top of the seat cover material.
Then, rotate the tether anchorage
cover directly behind the seat where
you are placing the child restraint,
push the tether strap and hook
through the access port and down into
the trunk. Open the access cover on
the carpet covering the back of the
seat and attach the tether strap hook
to the anchor. Be careful to route the
tether strap to provide the most direct
path between the anchor and the child
restraint. Finally, tighten all three
straps as you push the child restraint
rearward and downward into the seat,
removing slack in the straps accord-
ing to the child restraint manufactur-
er's instructions.
NOTE:
When using the ISOFIX attaching
system to install a child restraint,
please ensure that all seat belts not
being used for occupant restraints
are stowed and out of reach of chil-
dren. It is recommended that be-
fore installing the child restraint,
buckle the seat belt so the seat belt
is tucked behind the child re-
straint and out of reach. If the
buckled seat belt interferes with
the child restraint installation, in-
stead of tucking the seat belt be-
hind the child restraint, route the
seat belt through the child re-
straint belt path and then buckle
it. This should stow the seat belt
out of the reach of an inquisitive
child. Remind all children in the
vehicle that the seat belts are not
toys and should not be played
with, and never leave your child
unattended in the vehicle.
42

CONVERTIBLE TOP
OPERATIONCAUTION!
Failure to follow these cautions may
cause interior water damage, stains
or mildew on the top material:
 Avoid high-pressure car washes,as they can damage the top mate-
rial. Also, increased water pres-
sure may force water past the
weather strips.
 Remove any standing water from
the top and dry the surface before
opening it. Operating the top,
opening a door or lowering a win-
dow while the top is wet may al-
low water to drip into the vehicles
interior.
 Use care when washing the ve-
hicle, water pressure directed at
the weather strip seals may cause
water to leak into the vehicles in-
terior.
WARNING!
The convertible top does not provide
the structural protection that a rein-
forced metal roof does and the fabric
top cannot be expected to prevent
the ejection of the occupants in a
collision. Therefore, it is important
that all occupants wear their seat
belts at all times. Death or serious
injuries could occur if you are
ejected from the vehicle during a
collision.
You can lower or raise the power con-
vertible top from inside the vehicle or
lower the top remotely using the Re-
mote Keyless Entry (RKE) transmit-
ter. Either operation takes approxi-
mately 30 seconds. The entire
process, including unlatching or
latching the top at the windshield
header is automatic.
The top does take up some space in
the trunk when retracted. However,
the trunk will still hold a significant
amount of cargo. When operating the power convert-
ible top, the trunk lid will pivot at the
rear of the vehicle, swing open by the
rear window, and then pivot back-
ward. This allows room for the top to
retract into or unfold from its stowage
area in the trunk.
When lowering the top, the system
extends the hard tonneau cover,
which stows conveniently underneath
the trunk lid. The tonneau cover
closes the area between the rear seats
and the trunk lid to conceal the top
when stowed.
When raising the top, the system re-
tracts the hard tonneau cover back
into its stowage area underneath the
trunk lid.
To complete either operation, the
trunk lid returns to its normal posi-
tion and then latches.
Spring-loaded flipper doors, which
provide clearance for the linkage,
close off notches in the quarter trim
panels when the top is down.
53

POWER CONVERTIBLE
TOP USAGE PRECAUTIONS
NOTE:
 The convertible top will not op-erate unless the vehicle is sta-
tionary, the cargo shield is posi-
tioned correctly, and the trunk
lid is closed and latched. In ad-
dition, the system is prohibited
from opening when the ambient
temperature is below ­18°C.
 The top system is prohibited from closing when the ambient
temperature is below ­40°C.
 Do not attempt to lower the top when frost, ice, or snow may be
present, this could cause dam-
age or prevent the top from stow-
ing completely.
 The Power Top Control Module (PTCM) monitors and controls
lowering and raising of the top.
A series of micro-switches verify
that operations are complete be-
fore allowing the next stage of
lowering or raising operation.  Opening and closing the top
consecutively without the engine
running may run the battery
down.
 If a fluttering noise is heard from the rear seat belts while driving
with the top down, safely bring
the vehicle to a stop and buckle
the rear seat belts over the empty
seats. This will keep tension on
the seat belts and remove the
fluttering condition.
CAUTION!
 Correctly position the cargo shieldin the trunk before stowing the
top. Doing so closes a switch that
allows top operation (stowing) to
proceed. If the switch is not
closed, a warning message dis-
plays in the instrument cluster to
notify the driver.
 Always place items carefully into
the trunk.
 Do not push items too far into the
trunk, particularly when the top is
retracted into its stowage area in
the trunk.
(Continued)
CAUTION!(Continued)
 Do not use the area on top of the
tonneau cover for storage.
Failure to follow these cautions can
cause damage to the convertible top
components, trunk contents, cargo
shield, and the vehicle interior.CAUTION!
Before operating the power top:
 Always check on top of the ton-
neau cover area to be sure that it is
clear of debris or other items.
 Make sure the ambient tempera-
ture is above ­18°C if you want to
open the top.
 Make sure the ambient tempera-
ture is above ­40°C if you want to
close to the top.
 Never attempt to lower a frozen
convertible top. Wait until the top
is thawed before lowering it into
the stowage compartment. Low-
ering a cloth top at temperatures
below 0°C should be avoided.
(Continued)
54

CAUTION!(Continued)
 Make sure the convertible top is
dry before lowering it into the
stowage compartment. Lowering
the top when damp, wet, or dirty
can cause stains, mildew, and
damage to the inside of your ve-
hicle.
 Make sure there is sufficient clear-
ance of at least 2.2 m for the top to
move up.
 To prevent striking a low ceiling
or automatic door opener with the
top, it is strongly recommended
that you do not operate the power
top inside a garage or parking
structure.
Failure to follow these cautions can
cause damage to the convertible top
components, trunk contents, and the
vehicle interior.CAUTION!
 Do not operate the power top with
the hydraulic pump valve open.
(Continued)
CAUTION!(Continued)
 Do not allow the top to remain in
the suspended position. After ap-
proximately 10 minutes in the
suspended position, the hydraulic
pressure will release, which will
allow the top and the trunk lid to
lower. Pressing the power top
switch will cancel this operation.
 Always use a normal ice scraper to
remove snow or ice from the rear
window. Use of a sharp object or
other tools could scratch the pan-
els (hard top) or tear the fabric
(soft top) when removing snow or
ice.
 Always close the top when leaving
your vehicle so as not to leave the
interior exposed to potentially
damaging outdoor conditions.
 Do not leave the top lowered for
several weeks at a time. Close it
occasionally to prevent discolor-
ation in the folds of the fabric and
to allow the creases to smooth out.
This is especially important if the
top was stowed when not com-
pletely dry.
(Continued)
CAUTION!(Continued)
Failure to follow these cautions can
cause damage to the convertible top
components, trunk contents, and the
vehicle interior:WARNING!
Failure to follow these warnings can
result in injuries that are serious or
fatal to you, your passengers, and
others around you:
 Before operating the power top,
make sure that no moving parts of
the convertible top can injure a
person or animal.
 Never place any extremities
(hands, feet, etc.) near the con-
vertible top components, the up-
per windshield area, the shelf area
behind the rear seats, or the con-
vertible top stowage area while
raising or lowering the convertible
top.
 When using the power top button
on RKE transmitter, if potential
danger exists while lowering the
top, release the button immedi-
ately to interrupt the operation.
(Continued)
55

WARNING!(Continued)
 When using the power top switch
on the instrument panel, if poten-
tial danger exists while lowering
the top, release the switch imme-
diately to interrupt the operation.
 When using the power top switch
on the instrument panel, if poten-
tial danger exists while raising the
top, release the switch immedi-
ately to interrupt the operation.
 Only drive the vehicle with the
convertible top completely closed
and latched or fully lowered into
its stowage compartment.
 Do not operate the power top
when the vehicle is in motion.
CARGO SHIELD
The cargo shield is located in the
trunk. Before lowering the convertible
top, you must unfold the cargo shield
and seat the tabs at each end of the
cargo shield in the V slots in the trunk
liner. Doing so closes a switch that
allows top operation. If the switch is
not closed, a warning message dis-
plays in the instrument cluster to no-
tify the driver. Positioning The Cargo Shield For
Top Operation
Pull the cargo shield toward you to
begin unfolding the panels. Grasp the
handle in the center of the outermost
(top) panel and raise the cargo shield.
Then, align and seat the tabs at each
end of the cargo shield in the V slots in
the trunk liner as shown in the illus-
tration.
CAUTION!
Do NOT place items on top of the
cargo shield. Items placed on cargo
protector will interfere with the top
during operation and cause exces-
sive damage to the top and cargo
shield.
Positioning The Cargo Shield For
Cargo Storage
To maximize the storage space in the
trunk, the cargo shield can be stowed
in the forward portion of the trunk.
To stow the cargo shield, grasp the
handle of the upright panel of the
cargo shield, lifting the pins out of the
V slots in the trunk trim. Continue
folding the upright panel forward
onto the horizontal panel, then grasp
both panels and lift them to the for-
ward, upright position in the trunk.
NOTE:
The convertible top will NOT oper-
ate with the cargo shield in the
stowed position.
Cargo Shield
Stowed Cargo Shield
56