2012 FIAT PUNTO brake light

176
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND MESSAGES
IN AN
EMERGENCY
TECHNICAL
SPECIFICATIONS
INDEX
CONTROLS
AND DEVICES
SERVICE
AND CARE
fig. 7
Do not travel if the wind-
screen washer reservoir is
empty: using the windscreen washer
is essential for improving visibility.
WARNING
Some commercial additives
for windscreen washing are
flammable. The engine compartment
contains hot parts which could cause
a fire if they come into contact with
these additives.
WARNING
Prevent brake fluid, which is
highly corrosive, from coming
into contact with painted
parts. Wash with water im-
mediately if this should happen.WINDSCREEN/REAR WINDOW
WASHER FLUID fig. 6
To top up, remove the cap A.
Pour in a mixture of water and TUTELA
PROFESSIONAL SC35, in the follow-
ing concentrations:
30% TUTELA PROFESSIONAL
SC35 and 70% water in summer.
50% TUTELA PROFESSIONAL
SC35 and 50% water in winter.
If temperatures are below −20°C, use
undiluted TUTELA PROFESSIONAL
SC35 fluid.
Check the level through the reservoir.
fig. 6F0M0154mBRAKE FLUID fig. 7
Undo the cap Aand check that the liquid
contained in the reservoir is at the maxi-
mum level.
The fluid level in the reservoir must not
exceed the MAXmark.
If you need to top up, you should use the
brake fluid shown in the “Fluids and lu-
bricants” table (see “Technical Specifica-
tions”).
NB Carefully clean the reservoir cap A
and the surrounding surfaces.
When opening the cap, make sure that no
dirt gets into the reservoir.
Always use a funnel with a built-in filter
with a mesh of 0.12 mm or less for top-
ping up.
IMPORTANT Brake fluid absorbs mois-
ture. For this reason, if the car is mainly
used in areas with a high degree of at-
mospheric humidity, the fluid should be
replaced at more frequent intervals than
specified in the “Scheduled Servicing Plan”.F0M0155m
Brake fluid is poisonous and
highly corrosive. In the event
of accidental contact, wash the parts
immediately with water and mild
soap, then rinse with plenty of
water. Call a doctor immediately if
swallowed.
Symbol πon the container indicates
a synthetic brake fluid, which is dif-
ferent from a mineral fluid. Using a
mineral-type fluid will damage the
special rubber seals of the braking sys-
tem beyond repair.
WARNING
165-184 PUNTO POP 1ed EN 30-09-2011 10:21 Pagina 176

180
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND MESSAGES
IN AN
EMERGENCY
TECHNICAL
SPECIFICATIONS
INDEX
CONTROLS
AND DEVICES
SERVICE
AND CARE
WINDSCREEN/REAR
WINDOW WIPERS
BLADES
Regularly clean the rubber part using ap-
propriate products; TUTELA PRO-
FESSIONAL SC35 is recommended.
Replace the blades if the rubber edge is
misshapen or worn. In any event, it is ad-
visable to replace them approximately
once a year.
A few simple precautions can reduce the
possibility of damage to the blades:
❒make sure that the rubber part is not
frozen to the windscreen in sub-zero
temperatures. Use an antifreeze prod-
uct to release it if required;
❒remove any snow from the glass: in ad-
dition to protecting the blades, this pre-
vents the electric motor from over-
heating;
❒do not operate the windscreen wipers
on dry glass.
Driving with worn wiper
blades is a serious hazard,
because visibility is reduced in bad
weather.
WARNING
RUBBER TUBES
As far as the brake system and fuel rubber
hoses are concerned, stick closely to the
“Scheduled Servicing Plan” in this section.
Ozone, high temperatures and a pro-
longed lack of fluid in the system may
cause hardening and cracking of the tubes,
which could result in leaks. Careful in-
spections are therefore necessary.If the pressure is too low, the
tyre will overheat and could
be seriously damaged.
WARNING
Avoid switching the tyres
from the right side of the ve-
hicle to the left side and vice versa.
WARNING
Do not re-spray alloy wheel
rims at temperatures higher
than 150 °C. The mechanical char-
acteristics of the wheels may be
compromised.
WARNING
165-184 PUNTO POP 1ed EN 30-09-2011 10:21 Pagina 180

185
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND MESSAGES
IN AN
EMERGENCY
SERVICE
AND CARE
INDEX
CONTROLS
AND DEVICES
TECHNICAL
SPECIFICATIONS
IDENTIFICATION DATA ................................................. 186
ENGINE CODES – BODY WORK VERSIONS ............. 188
ENGINE ........................................................................\
.......... 189
FUEL SUPPLY ......................................................................\
.. 190
TRANSMISSION .................................................................. 190
BRAKES .......................................................................\
........... 191
SUSPENSIO NS .....................................................................\
. 191
STEERING SYSTEM ............................................................. 191
WHEELS ........................................................................\
......... 192
PERFORMANCES ................................................................ 195
DIMENSIONS .......................................................................\
196
WEIGHTS ........................................................................\
...... 197
CAPACIT IES ........................................................................\
.. 199
FLUIDS AND LU BRICANTS ............................................. 200
FUEL CONSUMPT ION ...................................................... 202
CO
2EMISSIONS .................................................................. 203
T
T
E
E
C
C
H
H
N
N
I
I
C
C
A
A
L
L


S
S
P
P
E
E
C
C
I
I
F
F
I
I
C
C
A
A
T
T
I
I
O
O
N
N
S
S
185-208 PUNTO POP 1ed EN 3-10-2011 11:50 Pagina 185

torsion beam with interconnected wheels
191
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND MESSAGES
IN AN
EMERGENCY
SERVICE
AND CARE
INDEX
CONTROLS
AND DEVICES
TECHNICAL
SPECIFICATIONS
BRAKES
1.2 - 1.4 - 1.3 Multijet
Service brakes:
– front disc (self-ventilating for versions/markets, where provided)
– rear drum
Parking brakecontrolled by hand lever, acting on rear brakes
IMPORTANT Water, ice and salt on the roads may deposit on the brake disc\
s, reducing braking efficiency the first time the brake s
are applied.
STEERING SYSTEM
1.2 - 1.4 - 1.3 Multijet
Type rack and pinion with electric power steering
Turning circle
(kerb to kerb) m 10,9
Independent wheel McPherson-typeIndependent wheel McPherson-type
with anti-roll bar
SUSPENSION
1.2 1.4 - 1.3 Multijet
Front
Rear
185-208 PUNTO POP 1ed EN 3-10-2011 11:50 Pagina 191

5 doors5 seats
1030
560
850
850
1590
900/500(
●)
400
50
60
3 doors 5 seats
1025
560
850
850
1585
1000 400
50
60
5 doors 5 seats
1040
560
850
850
1600
1000 400
50
60
197
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND MESSAGES
IN AN
EMERGENCY
SERVICE
AND CARE
INDEX
CONTROLS
AND DEVICES
TECHNICAL
SPECIFICATIONS
WEIGHTS
1.2 1.4
Weights (kg)
Unladen weight (with all fluids,
fuel tank filled to 90% and
without optional equipment):
Payload (*) including the driver:
Maximum permitted loads (**)
– front axle:
– rear axle:
– total:
Towable loads:
– braked trailer:
– non-braked trailer:
Maximum load on roof:
Maximum load on the
ball joint (braked trailer):
(*) If special equipment is fitted (sunroof, tow hitch, etc.) the unladen \
car weight increases, thus reducing the specified payload with respect to the maximum permitted load.
(**) Loads that must not be exceeded. The driver is responsible for arranging\
the goods in the boot and/or on the load carrying platform
within the maximum permitted loads.
(●)Versions ECO.
3 doors 5 seats
1015
560
850
850
1575
900/500(
●)
400
50
60
185-208 PUNTO POP 1ed EN 3-10-2011 11:50 Pagina 197

198
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND MESSAGES
IN AN
EMERGENCY
SERVICE
AND CARE
INDEX
CONTROLS
AND DEVICES
TECHNICAL
SPECIFICATIONS
3 doors 5 seats
1090
560
950
850
1650
1000 400
50
60
5 doors 5 seats
1105
560
950
850
1665
1000 400
50
60
3 doors 5 seats
1130
560
950
850
1690
1000 400
50
60
5 doors 5 seats
1145
560
950
850
1705
1000 400
50
60
1.3 Multijet 75HP 1.3 Multijet 85HP
Weights (kg)
Unladen weight (with all fluids,
fuel tank filled to 90% and
without optional equipment):
Payload (*) including the driver:
Maximum permitted loads (**)
– front axle:
– rear axle:
– total:
Towable loads:
– braked trailer:
– non-braked trailer:
Maximum load on roof:
Maximum load on the
ball joint (braked trailer):
(*) If special equipment is fitted (sunroof, tow hitch, etc.) the unladen \
car weight increases, thus reducing the specified payload with respect to the maximum permitted load.
(**) Loads that must not be exceeded. The driver is responsible for arranging\
the goods in the boot and/or on the load carrying platform
within the maximum permitted loads.
185-208 PUNTO POP 1ed EN 3-10-2011 11:50 Pagina 198

1.3 Multijet85HP
–
–
45
5 ÷ 7
6.7 –
–
3.0
3.2
1.7 (
■)
0.5
2.2
4.5
1.4
45
5 ÷ 7
–
–
5.3
2.4
2.6 –
–
1.5 (
●)
0.5
2.2
4.5
1.2
45
5 ÷ 7
–
–
5.3
2.4
2.6 –
–
1.5 (
●)
0.5
2.2
4.5
CAPACITIES
Fuel tank: litres
including a reserve of: litres
Fuel tank: litresincluding a reserve of: litres
Engine cooling
system: litres
Engine sump: litres
Engine sump and filter: litres
Engine sump: litres
Engine sump and filter: litres
Gearbox/differential
casing: kg
Hydraulic brake circuit: kg
Windscreen/rear window
washer fluid reservoir: litres
with headlight washers: litres
( ❒ ) For particularly harsh climate conditions, a mixture of 60% PARAFLUUPand 40% distilled water is recommended.
(
▲) Per condizioni climatiche particolarmente rigide, si consiglia l’util\
izzo di TUTELA TRANSMISSION GEARFORCE.
Recommended fuels
and original lubricants
Unleaded petrol with no less
than 95 R.O.N.
(EN228 Specification)
Diesel for motor vehicles
(EN590 Specification)
50-50 mixture of water and
PARAFLU
UPliquid (❒)
SELENIA K P.E.
SELENIA WR P.E.
TUTELA
CAR TECHNYX (
●) (▲)
TUTELA TRANSMISSION
GEARFORCE(■)
TUTELA TOP 4
Mixture of water and
TUTELA
PROFESSIONAL SC35
199
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND MESSAGES
IN AN
EMERGENCY
SERVICE
AND CARE
INDEX
CONTROLS
AND DEVICES
TECHNICAL
SPECIFICATIONS
1.3 Multijet
75HP
–
–
45
5 ÷ 7
7.4 (Euro 4)
6.7 (Euro 5) –
–
3.0
3.2
1.7 (
●)
0.5
2.2
4.5
185-208 PUNTO POP 1ed EN 3-10-2011 11:50 Pagina 199

201
SAFETY
STARTING
AND DRIVING
WARNING
LIGHTS AND MESSAGES
IN AN
EMERGENCY
SERVICE
AND CARE
INDEX
CONTROLS
AND DEVICES
TECHNICAL
SPECIFICATIONS
Brake liquid
Fuel additive
Use Quality specifications of fluids and lubricants OriginalApplicationsfor correct car operation fluids and lubricants
(*) IMPORTANT Do not use fluids with different specifications for topping up\
or mixing.
(❒ ) When the vehicle is used in particularly harsh climate conditions, we re\
commend using a 60-40 mixture of PARAFLU
UPand distalled water.
Windscreen/rear
window washer
fluid Mechanical gearbox and
differential (petrol and
1.3 Multijet 75HP versions)
Mechanical gearbox and
differential (1.3 Multijet
85HP versions)
Wheel side
constant-velocity joints
Differential side
constant-velocity joints
Hydraulic brakes
and hydraulic clutch con-
trols
Cooling circuit.
Mixture: 50% water and
50%
PARAFLU
UP(❒ )
Mix 25cc per 10 litres of
diesel
To be used diluted or
undiluted in windscreen/
rear window washer/
wiper systems
TUTELA CAR TECHNYX
Contractual Technical
Reference N° F010.B05
TUTELA TRANSMISSION
GEARFORCE
Contractual Technical
Reference N° F702.G07
TUTELA ALL STAR
Contractual Technical
Reference N° F702.G07
TUTELA STAR 700
Contractual Technical
Reference N° F701.C07
TUTELA TOP 4
Contractual Technical
Reference N° F001.A93
PARAFLU
UP(*)
Contractual Technical
Reference N° F101.M01
TUTELA DIESEL ART
Contractual Technical
Reference N° F601.L06
TUTELA
PROFESSIONAL SC35
Contractual Technical
Reference N° F201.D02
Lubricants
and greases
for drive
transmission
system
Radiator
protection
SAE 75W-85 grade synthetic base lubricant.
FIAT 9.55550-MX3 certification
SAE 75W grade synthetic base lubricant.
FIAT 9.55550-MZ6 certification
Molybdenum disulphide grease, for use at
high temperatures.
FIAT 9.55580 certification
. NL.GI. 1-2 consistency
Grease for constant-velocity joints with low
friction coefficient.
FIAT 9.55580 certification . NL.GI. 0-2 consistency
Synthetic fluid FMVSS n° 116 DOT 4, ISO 4925
SAE J1704, CUNA NC 956- 01.
FIAT 9.55597 certification
Inhibited mono ethylene glycol-based antifreeze
protection, red, with organic formulation.
Passes CUNA NC 956-16, ASTM D 3306 specifications.
FIAT 9.55523 certification
Additive for diesel antifreeze, protecting
diesel engines
Mixture of alcohol, water and surfactants
CUNA NC 956-II
FIAT 9.55522 certification .
185-208 PUNTO POP 1ed EN 3-10-2011 11:50 Pagina 201