Page 181 of 210

180
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
INTERIORS
Periodically check that water is not
trapped under the mats (due to water
dripping off shoes, umbrellas, etc.) which
could cause oxidisation of the sheet met-
al.
CLEANING SEATS AND FABRIC
AND VELVET PARTS
Use a soft brush or vacuum cleaner to re-
move dust. Velvet is cleaned better if the
brush is moistened.
Rub the seats with a sponge moistened
with a solution of water and neutral de-
tergent.
CLEANING LEATHER SEATS
Remove dried on dirt with lightly moist-
ened chamois leather or cloth without
pressing too hard.
Remove liquid or grease stains with a dry
absorbent cloth without rubbing. Then
wipe with a soft cloth or chamois leather
with water and neutral soap.
If the stain persists, use specific products,
carefully following the instructions for use.
IMPORTANT Never use spirit or alcohol-
based products.INTERIOR PLASTIC PARTS
For routine cleaning, wipe with a cloth
with water and neutral non-abrasive de-
tergent. Remove grease or persistent
stains with appropriate products designed
to preserve the appearance of compo-
nents.
IMPORTANT Never use spirit or petro-
leum to clean the instrument panel or oth-
er plastic parts.
Do not keep aerosol cans in
the car: they might explode.
Aerosol cans must never be exposed
to a temperature above 50°C. The
temperature inside the car exposed
to the sun may go well beyond that
figure.
WARNING
Upholstery of your car has
been designed to withstand
wear deriving from common
use of the car. You are how-
ever recommended to avoid strong
and/or continuous scratching with
clothing accessories such as metallic
buckles, studs, Velcro fastenings and
the like, since these items cause cir-
cumscribed stress of the cover fabric
that could lead to yarn breaking, and
damage the cover as a consequence.
STEERING WHEEL / GEARBOX
LEVER KNOB AND SEATS
COATED WITH REAL LEATHER
These components shall only be cleaned
with water and neutral soap. Never use
spirit or alcohol-based products.
Before using special products for clean-
ing interiors, read carefully label instruc-
tions and indications to make sure they
are free from spirit and/or alcohol-based
substances.
If when cleaning the windscreen with spe-
cial glass products, some drops fall on the
leather covering of the steering wheel/gear
lever knob remove them immediately and
then clean with water and neutral soap.
IMPORTANT Take the utmost care when
engaging the steering lock to prevent
scratching the leather covering.
161-180 idea GB 1 ed 10-07-2008 8:30 Pagina 180
Page 182 of 210

181
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IDENTIFICATION DATA ................................................. 182
ENGINE CODES - BODYWORK VERSIONS .............. 184
ENGINE ................................................................................. 185
FUEL FEED/IGNITION ....................................................... 187
TRANSMISSION .................................................................. 187
BRAKES ................................................................................... 188
SUSPENSIONS ....................................................................... 188
STEERING............................................................................... 188
WHEELS .................................................................................. 189
DIMENSIONS ........................................................................ 193
PERFORMANCE ................................................................... 193
WEIGHTS ............................................................................... 194
CAPACITIES........................................................................... 195
FLUIDS AND LUBRICANTS ............................................. 196
FUEL CONSUMPTION ....................................................... 198
CO
2EMISSIONS ................................................................. 199
TT T
E E
C C
H H
N N
I I
C C
A A
L L
S S
P P
E E
C C
I I
F F
I I
C C
A A
T T
I I
O O
N N
S S
181-199 idea GB 1 ed 10-07-2008 8:31 Pagina 181
Page 183 of 210

182
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
IDENTIFICATION DATA
You are advised to note the identification
codes. The identification data stamped and
given on the plates and their position are
the following fig. 1:
1- Model plate
2- Chassis marking
3- Bodywork paint identification plate
4- Engine marking.
MODEL PLATE fig. 2
The plate is to be found on the front
crossmember of the engine compartment
and bears the following identification da-
ta:
B- Homologation number.
C- Vehicle type code.
D- Chassis number.
E- Maximum vehicle weight fully loaded.
F- Maximum vehicle weight fully loaded
with trailer.G- Maximum vehicle weight on front axle.
H- Maximum vehicle weight on rear axle.
I - Engine type.
L- Body version code.
M- Spare part code.
N- Smoke opacity index (for diesel en-
gines).
fig. 1
4
21
3F0H0225mfig. 2F0H0760m
181-199 idea GB 1 ed 10-07-2008 8:31 Pagina 182
Page 184 of 210
183
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
HASSIS MARKING fig. 3
It is printed on the passenger compart-
ment floor, near the right-hand front seat.
It can be reached by lifting the special flap
in the carpeting and includes the following
data:
❒car model;
❒chassis number.
fig. 3F0H0227m
fig. 4F0H0228m
BODYWORK PAINT
IDENTIFICATION PLATE fig. 4
It is applied on front bonnet and shows fol-
lowing data:
A- Paint manufacturer.
B- Colour name.
C- Fiat colour code.
D- Respray and touch up code.
ENGINE MARKING
Engine marking is stamped on the cylinder
block on passenger compartment side and
includes the model and the chassis num-
ber.
181-199 idea GB 1 ed 10-07-2008 8:31 Pagina 183
Page 185 of 210

184
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
ENGINE CODES - BODYWORK VERSIONS
Versions
1.2
16V
1.48V (◊)
1.416V
1.416V90 CV(◊)
1.3 Multijet 70 HP
1.3 Multijet 90 HP
1.6 Multijet
1.6 Multijet 115 HP (◊)
1.9 Multijet 100 HP (◊)
(◊) Engine model provided for certain versions/markets only
(*) Version with DPFEngine code
188A5000
350A1000
843A1000
192B2000
188A9000
199A3000
350A2000
350A3000
188B2000Bodywork version code
350 AXD1A 03 (5 seats)
350 AXD1A 03C (4 seats)
350 AXF1A 08 (5 seats)
350 AXF1A 08B (4 seats)
350 AXA1B 07E (5 seats)
350 AXA1B 07F (4 seats)
350 AXE1A 06
350 AXB1A 01N (5 seats)
350 AXB1A 01P (4 seats)
350 AXG1A 09AA (5 seats)
350 AXG1A 09AB (4 seats)
350 AXG1A 09AC (5 seats) (*)
350 AXG1A 09AD (4 seats) (*)
350 AXH1A 11 (5 seats) (*)
350 AXH1A 11B (4 seats) (*)
350 AXL1A 12 (5 seats) (*)
350 AXL1A 12B (4 seats) (*)
350 AXC1A 02F (5 seats)
350 AXC1A 02E (4 seats)
181-199 idea GB 1 ed 10-07-2008 8:31 Pagina 184
Page 186 of 210
185
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
1.48V (◊)
350A1000
Otto
4 in line
2
72 x 84
1368
11 ± 0.2
57
77
6000
115
11.7
3000
NGK ZKR7A-10
Unleaded petrol
95 RON
(EN228 Specifications)
ENGINE
GENERAL FEATURES
Engine code
Cycle
Number and layout of cylinders
Valves per cylinder
Piston bore and stroke mm
Total displacement cm3
Compression ratio
Maximum power (EEC) kW
HP
corresponding ratio: rpm
Maximum torque (EEC) Nm
kgm
corresponding ratio: rpm
Spark plugs
Fuel
(◊) Engine model provided for certain versions/markets only
1.216V
188A5000
Otto
4 in line
4
70.8 x 78.86
1242
10.6 ± 0.2
59
80
5000
114
11.6
4000
NGK DCPR7E-N-10
BOSCH YR7DEU
Unleaded petrol
95 RON
(EN228 Specifications)1.4
16V
843A1000
Otto
4 in line
4
72 x 84
1368
11 ± 0.2
70
95
5800
128
13
4500
NGK ZKR7A-10
Unleaded petrol
95 RON
(EN228 Specifications)
181-199 idea GB 1 ed 10-07-2008 8:31 Pagina 185
Page 187 of 210
186
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
GENERAL FEATURES
Engine code:
Cycle:
Number and layout of cylinders:
Valves per cylinder:
Piston bore and stroke mm:
Total displacement cm3
:
Compression ratio:
Maximum power (EEC): kW
HP
corresponding ratio: rpm
Maximum torque (EEC): Nm
kgm
corresponding ratio: rpm
Spark plugs:
Fuel:
1.6 Multijet
350A2000
Diesel
4 in line
4
79.5 x 80.5
1598
16.5 ±1
88
120
3500
300
30.5
1500
–
Diesel fuel
for motor vehicles
(EN590 Specifications) 1.3 Multijet 70 HP
188A9000
Diesel
4 in line
4
69.6 x 82
1248
18 ±0.4
51
70
4000
180
18.3
1750
–
Diesel fuel
for motor vehicles
(EN590 Specifications)1.3 Multijet 90 HP
199A3000
Diesel
4 in line
4
69.6 x 82
1248
17.6 ±0.4
66
90
4000
200
20
1750
–
Diesel fuel
for motor vehicles
(EN590 Specifications)
181-199 idea GB 1 ed 10-07-2008 8:31 Pagina 186
Page 188 of 210

187
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
TRANSMISSION
Gearbox
Clutch
Drive
(◊) Engine model provided for certain versions/markets only1.2
16V - 1.48V (◊)- 1.3 Multijet - 1.6 Multijet
Five forward gears and reverse with synchromesh
for forward gear engagement
Hydraulic control, self-adjusting without
travel-free pedal
Front1.416V
Five or six forward gears and reverse with
synchromesh for forward gear engagement
Hydraulic control, self-adjusting without travel-free
pedal
Front
Modifications or repairs to the fuel system that are not carried out properly or do not take the system’s techni-
cal specifications into account can cause malfunctions leading to the risk of fire.
FUEL FEED/IGNITION
Fuel feed
(◊) Engine model provided for certain versions/markets only1.3 Multijet - 1.6 Multijet
Direct injection with electronically controlled
Multijet “Common Rail” with turbosupercharger
and intercooler 1.2
16V - 1.48V (◊) - 1.416V
Multipoint sequential phased electronic injection,
returnless system
181-199 idea GB 1 ed 10-07-2008 8:31 Pagina 187