2012 FIAT FREEMONT bulb

The TPMS has been optimized for the
original equipment tires and wheels.
TPMS pressures and warning have been
established for the tire size equipped on your
vehicle. Undesirable system operation or sensor
damage may result when using replacement
equipment that is not of the same size, type,
and/or style.Aftermarket wheels can cause sensor
damage. Do not use aftermarket tire sealants or
balance beads if your vehicle is equipped with a
TPMS, as damage to the sensors may result . (Re-
fer to “Tire Inflation Pressures” under “Tires —
General Information” and to “Tire Pressure Moni-
tor System (TPMS)” in “Technical Specifications”
for further information).
10. Seat Belt Reminder Light When the ignition switch is first turned to ON/
RUN, this light will turn on for four to eight
seconds as a bulb check. During the bulb check,
if the driver's seat belt is unbuckled, a chime will sound.
After the bulb check or when driving, if the driver seat
belt remains unbuckled, the Seat Belt Warning Light
will flash or remain on continuously. Refer to “Occu-
pant Restraints” in “Safety” for further information. 11. Brake Warning Light
This light monitors various brake functions,
including brake fluid level and parking brake
application. If the brake light turns on it may
indicate that the parking brake is applied, that
the brake fluid level is low, or that there is a problem
with the anti-lock brake system reservoir.
If the light remains on when the parking brake has been
disengaged, and the fluid level is at the full mark on the
master cylinder reservoir, it indicates a possible brake
hydraulic system malfunction or that a problem with
the Brake Booster has been detected by the Anti-Lock
Brake System (ABS) / Electronic Stability Program
(ESP) system. In this case, the light will remain on until
the condition has been corrected. If the problem is
related to the brake booster, the ABS pump will run
when applying the brake and a brake pedal pulsation
may be felt during each stop.
The dual brake system provides a reserve braking
capacity in the event of a failure to a portion of the
hydraulic system. A leak in either half of the dual brake
system is indicated by the Brake Warning Light, which
will turn on when the brake fluid level in the master
cylinder has dropped below a specified level.
The light will remain on until the cause is corrected.
NOTE: The light may flash momentarily during sharp
cornering maneuvers, which change fluid level condi-
tions. The vehicle should have service performed, and
the brake fluid level checked.
228
KNOWING YOUR
VEHICLE
SAFETY
STARTING AND
DRIVINGWARNING LIGHTSAND
MESSAGES
IN AN
EMERGENCY
SERVICING AND
CARETECHNICAL
SPECIFICATIONSCONTENTS

4. Clean any remaining sealant from the TIREFIT hous-ing.
5. Position the new Sealant Bottle (1) in the housing so that the Sealant Hose (6) aligns with the hose slot in
the front of the housing. Press the bottle into the
housing. An audible click will be heard indicating the
bottle is locked into place.
6. Verify that the cap is installed on the fitting at the end of the Sealant Hose (6) and return the hose to
its storage area (located on the bottom of the airpump).
7. Return the TIREFIT kit to its storage location in the vehicle. REPLACEMENT BULBS
All the inside bulbs are brass or glass wedge base.
Aluminum base bulbs are not approved and should not
be used for replacement.
LIGHT BULBS – Interior Bulb Number
Courtesy/Reading Lamps (Incandescent) . . . . . . . . . . 578
Courtesy/Reading Lamps
(Optional LED) . . . . LED (Serviced at Authorized Dealer)
Glove Box Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . 194
Cargo Lamp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 579
Optional Door Map
Pocket/Cupholder . . LED (Serviced at Authorized Dealer)
NOTE:
For lighted switches, see your authorized
dealer for replacement instructions.
LIGHTS BULBS – Outside Bulb No.
Low Beam Headlamp . . . . . . . . . . . . . . . . . . . . . . . H1
High Beam Headlamp . . . . . . . . . . . . . . . . . . HB3/9005
Front Turn Signal . . . . . . . . . . . . . . . . PY27W/3757AK
Front Position Lamp . . . . . . . . . . . . . . . . . . . . . W5W
Front Fog Lamp . . . . . . . . . . . . . . . . . . . . . . PSX24W
Rear Fog Lamp . . . . . . . . . . . . . . . . . . . . . . . . PS19W
Side Repeater Lamp. . . . . . . . . . . . . . . . . . . . . WY5W
Center High Mounted Stop Lamp (CHMSL) . . . . . . . LED
(Serviced at Authorized Dealer)
Rear Tail/Stop . . . . . LED (Serviced at Authorized Dealer)
Rear Tail Liftgate . . . LED (Serviced at Authorized Dealer)
Rear Turn Signal . . . . . . . . . . . . . . . . . . . . . . WY21W
Backup Lamp . . . . . . . . . . . . . . . . . . . . . . . . . W21W
License Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
248
KNOWING YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTSAND
MESSAGES
IN AN
EMERGENCY
SERVICING AND
CARETECHNICAL
SPECIFICATIONSCONTENTS

BULB REPLACEMENT
LOW BEAM/HIGH BEAM/FRONT TURN
SIGNAL AND FRONT POSITION LAMP
1. Open the hood.
NOTE:It may be necessary to remove the air cleaner
filter housing and position the Totally Integrated Power
Module (TIPM) aside to replace certain lamps in the left
headlamp housing.
2. Rotate the applicable bulb and connector assembly
1∕4turn counterclockwise and remove the assembly
from the headlamp housing. (fig. 165) 3. Disconnect the bulb from the harness connector
and then connect the replacement bulb.
Do not touch the new bulb with your
fingers. Oil contamination will severely
shorten bulb life. If the bulb comes in
contact with any oily surface, clean the bulb with
rubbing alcohol.
4. Install the bulb and connector assembly into the headlamp housing and rotate it
1∕4turn clockwise to
lock it in place.
FRONT FOG LAMP
NOTE: Turn the steering wheel to the right if replac-
ing the left front fog lamp or to the left if replacing the
right front fog lamp to allow for easier access to the
front of the wheel well.
1. Remove the fasteners retaining the front lower wheel well access panel and remove the access panel.
2. Remove the electrical connector from the fog lamp housing. (fig. 166)
3. Firmly grasp the bulb by the two side latches and squeeze them together to unlock the bulb from the
back of the front fog lamp housing.
4. Pull the bulb straight out from the keyed opening in the housing.
(fig. 165)
1 — Front Turn Signal Lamp Bulb
2 — Low Beam Headlamp Bulb
3 — Front Position Bulb
4 — High Beam Headlamp Bulb
249
KNOWING
YOURVEHICLE SAFETY
STARTING ANDDRIVING
WARNING LIGHTSAND
MESSAGESIN AN
EMERGENCYSERVICING AND
CARETECHNICAL
SPECIFICATIONSCONTENTS

5. Align the index tabs of the replacement front foglamp bulb with the slots in the collar of the bulb
opening on the back of the front fog lamp housing.
Do not touch the new bulb with your
fingers. Oil contamination will severely
shorten bulb life. If the bulb comes in
contact with an oily surface, clean the bulb with
rubbing alcohol.
6. Insert bulb into the lamp housing until the index tabs are engaged in the slots of the collar.
7. Firmly and evenly push the bulb straight into the lamp housing until both side latches lock firmly into
place. REAR FOG LAMP
1. Reach behind the bumper above the bumper rein-
forcement and press the release tabs on the fog
lamp housing. (fig. 167)
2. Separate the fog lamp housing from the bumper fascia.
3. Disconnect the electrical harness connector. (fig. 168)
4. Firmly grasp the bulb by the two side latches and squeeze them together to unlock the bulb from the
back of the lamp housing.
5. Pull the bulb straight out from the keyed opening in the housing
6. Remove the bulb from the connector socket and install the replacement bulb.
(fig. 166)
(fig. 167) Release Tabs
250
KNOWING YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTSAND
MESSAGES
IN AN
EMERGENCY
SERVICING AND
CARETECHNICAL
SPECIFICATIONSCONTENTS

7. Align the index tabs of the replacement rear foglamp bulb/socket assembly with the slots in the
collar of the bulb opening on the back of the lamphousing.
8. Insert bulb into the lamp housing until the index tabs are engaged in the slots of the collar.
9. Firmly and evenly push the bulb straight into the lamp housing until both side latches lock firmly into
place.
10. Reinstall the fog lamp housing.
SIDE REPEATER LAMP
The side repeater lamps are located in both front
fender panels.
1. Push the side repeater lens to left side to release the spring tension and then pull it outward. 2. Disconnect the bulb from the harness connector
and then connect the replacement bulb. (fig. 169)
3. Engage the right hook of the side repeater lamp into the sheet metal (note correct orientation of letter-
ing on lens).
4. Rotate the side repeater lamp in place until the left side engages (you will hear a light click).
REAR TURN SIGNAL AND BACKUP LAMP
The taillamps are a two-piece design. The tail/stop/rear
turn signal lamps are located in the rear corner body
panels. The tail and backup lamps are located in the
liftgate.
Changing the Rear Turn Signal Lamp
1. Open the liftgate.(fig. 168) Electrical Connector
(fig. 169)Side Repeater Bulb Removal
251
KNOWING
YOURVEHICLE SAFETY
STARTING ANDDRIVING
WARNING LIGHTSAND
MESSAGESIN AN
EMERGENCYSERVICING AND
CARETECHNICAL
SPECIFICATIONSCONTENTS

2. Remove the two fasteners from the inboard side ofthe taillamp housing. (fig. 170)
3. Carefully insert a trim stick (plastic flat-blade tool) between the body panel and the outboard side of
the taillamp housing with one hand and grasp the
flange on the inboard side of the taillamp housing
with the other hand. Use the trim stick and hand
pressure together to disengage the taillamp housing
from the vehicle.
4. Rotate the applicable bulb's electrical connector
1∕4
turn counterclockwise and remove it from the tail-
lamp housing.
5. Remove the bulb from the connector socket and install the replacement bulb.
6. Install the bulb and connector assembly into the taillamp housing and rotate the connector
1∕4turn
clockwise to lock it in place. 7. Reinstall the taillamp housing and fasteners.
Changing the Backup Lamp
1. Open the liftgate.
2. Remove the two fasteners retaining the taillamp
housing to the liftgate from the inboard face of the
liftgate. (fig. 171)
3. Carefully insert a trim stick (plastic flat-blade tool) between the taillamp housing and the liftgate. Use
the trim stick and hand pressure together to disen-
gage the taillamp housing from the liftgate.
(fig. 172)
4. Rotate the applicable bulb's electrical connector
1∕4
turn counterclockwise and remove it from thehousing.
5. Remove the bulb from the connector socket and install the replacement bulb.
(fig. 170)
(fig. 171)
252
KNOWING YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTSAND
MESSAGES
IN AN
EMERGENCY
SERVICING AND
CARETECHNICAL
SPECIFICATIONSCONTENTS

6. Install the bulb and connector assembly into thehousing and rotate the connector
1∕4turn clockwise
to lock it in place.
7. Reinstall the taillamp housing and fasteners.
LICENSE PLATE LAMP
1. Push the small locking tab sticking out of the end of the lens toward the side of the vehicle and hold it in
that position.
2. Insert a small flat-blade tool between the end of the lens with the locking tab and the surrounding hous-
ing and then pivot the tool to separate the lens from
the housing.
3. Hold the lens with one hand and rotate the bulb's electrical connector
1∕4turn counterclockwise with
the other hand and then separate the bulb and
connector assembly from the lens. 4. Remove the bulb from the connector socket and
install the replacement bulb.
5. Install the bulb and connector assembly into the lens and rotate the connector
1∕4turn clockwise to
lock it in place.
6. Insert the end of the lens without the locking tab into the housing on the liftgate and then push the
opposite end of the lens into the housing, making
sure it locks in the housing.
(fig. 172)
253
KNOWING
YOURVEHICLE SAFETY
STARTING ANDDRIVING
WARNING LIGHTSAND
MESSAGESIN AN
EMERGENCYSERVICING AND
CARETECHNICAL
SPECIFICATIONSCONTENTS

Brake Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303
Brake System . . . . . . . . . . . . . . . . . . . . . . . . 113,284Anti-Lock (ABS) . . . . . . . . . . . . . . . . . . . . 113,114
Fluid Check . . . . . . . . . . . . . . . . . . . . . . . 284,303
Master Cylinder . . . . . . . . . . . . . . . . . . . . . . . 284
Parking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200
Warning Light . . . . . . . . . . . . . . . . . . . . . . . . . 228
Brake, Parking . . . . . . . . . . . . . . . . . . . . . . . . . . 200
Brake/Transmission Interlock . . . . . . . . . . . . . . . . 204
Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113,284
Break-In Recommendations, New Vehicle . . . . . . . . 195
Brightness, Interior Lights . . . . . . . . . . . . . . . . . . . 74
Bulb Replacement . . . . . . . . . . . . . . . . . . . . . 248,249
Bulbs, Light . . . . . . . . . . . . . . . . . . . . . . . . . 194,248
Camera, Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
Capacities, Fluid . . . . . . . . . . . . . . . . . . . . . . . . . 301
Caps, Filler Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
Oil (Engine) . . . . . . . . . . . . . . . . . . . . . . . 271,273
Power Steering . . . . . . . . . . . . . . . . . . . . . . . . 122
Radiator (Coolant Pressure) . . . . . . . . . . . . . . . 282
Car Washes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287
Carbon Monoxide Warning . . . . . . . . . . . . . . . . . 192
Cargo (Vehicle Loading) . . . . . . . . . . . . . . . . . . . . 107
Cargo Area Cover . . . . . . . . . . . . . . . . . . . . . . . 109
Cargo Area Features . . . . . . . . . . . . . . . . . . . . . . 106
Cargo Compartment . . . . . . . . . . . . . . . . . . . . . . 106 Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Luggage Carrier . . . . . . . . . . . . . . . . . . . . . . . . 112
Cargo Load Floor . . . . . . . . . . . . . . . . . . . . . . . . 107
Cargo Management System . . . . . . . . . . . . . . . . . . 107 Rollaway Tonneau Cover . . . . . . . . . . . . . . . . . . 109 Tri-Fold Load Floor . . . . . . . . . . . . . . . . . . . . . 107
Cargo Tie-Downs . . . . . . . . . . . . . . . . . . . . . . . . 108
Cellular Phone . . . . . . . . . . . . . . . . . . . . . . . . . . 155
Changing A Flat Tire . . . . . . . . . . . . . . . . . . . . . . 234
Checking Your Vehicle For Safety . . . . . . . . . . . . . . 192
Checks, Safety . . . . . . . . . . . . . . . . . . . . . . . . . . 192
Child Booster Seat . . . . . . . . . . . . . . . . . . . . . . . 174
Child Restraint . . . . . . . . . . . . . . 170,173,175,177,179
Child Restraint Tether Anchors . . . . . . . . . . . . 176,177
Child Safety Locks . . . . . . . . . . . . . . . . . . . . . . . . 98
Clean Air Gasoline . . . . . . . . . . . . . . . . . . . . . . . 299Cleaning Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 288
Windshield Wiper Blades . . . . . . . . . . . . . . . . . 277
Climate Control . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Coin Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Cold Weather Operation . . . . . . . . . . . . . . . . . . . 197
Compact Disc (CD) Maintenance . . . . . . . . . . . . . 155
Compact Spare Tire . . . . . . . . . . . . . . . . . . . . . . 294
Computer, Trip/Travel . . . . . . . . . . . . . . . . . . . . . . 25
Connector UCI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
Universal Consumer Interface (UCI) . . . . . . . . . . 154
Conserving Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Console, Floor . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Console, Overhead . . . . . . . . . . . . . . . . . . . . . . . . 83
Cool Down, Turbo . . . . . . . . . . . . . . . . . . . . . . . 199
Coolant Pressure Cap (Radiator Cap) . . . . . . . . . . . 282
Cooling System . . . . . . . . . . . . . . . . . . . . . . . . . 280 Adding Coolant (Antifreeze) . . . . . . . . . . . . 281,282
Coolant Capacity . . . . . . . . . . . . . . . . . . . . . . . 301
Coolant Level . . . . . . . . . . . . . . . . . . . . . . 280,283
Diesel Engine . . . . . . . . . . . . . . . . . . . . . . . . . 280
308
KNOWING YOUR
VEHICLE
SAFETY
STARTING AND
DRIVING
WARNING LIGHTSAND
MESSAGES
IN AN
EMERGENCY
SERVICING AND
CARETECHNICAL
SPECIFICATIONSCONTENTS