2012 FIAT DUCATO mirror controls

48
KNOWING
YOUR CAR
SAFETY
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
INDEX
F0N0500mfig. 48
Window demisting
In the event of considerable external moisture and/or rain
and/or large differences in temperature inside and outside
the passenger compartment, perform the following
preventive window demisting procedure:
❒turn the ring nut A to the red section;
❒switch off the air recirculation by turning the knob D
to
Ú;
❒turn the ring nut C to -or to ®if the windows
do not demist;
❒turn the knob B to the 2ndspeed.
HEATED REAR WINDSCREEN AND DOOR
MIRRORS DEMISTING/DEFROSTING fig. 49
(for versions/markets where provided)
Press the button A to activate this function; when this
function is on the warning light in the button comes on.
This function is timed and will turn off automatically
after 20 minutes. Press the button A again to switch the
function off.
IMPORTANT Do not apply stickers to the inside of the
rear window over the heating filaments to avoid damage
that might cause it to stop working properly. FRONT WINDOW FAST
DEMISTING/DEFROSTING (WINDSCREEN
AND SIDE WINDOWS)
Proceed as follows:
❒turn the ring nut A to the red section;
❒switch off the air recirculation by turning the knob D
to
Ú;
❒turn the ring nut C to -;
❒turn the knob B to 4 -(max. fan speed).
IMPORTANT To ensure fast demisting/defrosting,
if a supplementary heater is present (under the front or
rear seat for Panorama and Combi versions), if on, turn
off using button F (LED off) located on the control panel
fig. 48.
After demisting/defrosting, operate the controls to
restore the required comfort conditions.

55
KNOWING
YOUR CAR
SAFETY
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
INDEX
E System off button.
F Compressor enabling/disabling button.
G Air recirculation control button.
H Fan speed increase/decrease control buttons.
I Temperature increase/decrease control knob.
USING THE CLIMATE CONTROL SYSTEM
The system can be started in different ways, but it is
advisable to start by pressing the AUTO button and
then turning the knob to set the temperature required
on the display. The system will start running
automatically in this way and the set temperature will be
reached as quickly as possible. The system will adjust
the temperature, the quantity and the distribution of the
air introduced into the passenger compartment and, by
managing the recirculation function, the activation of the
compressor. During fully automatic operation, the only
manual intervention required is the possible activation
of the following functions:
❒Òair recirculation, to keep it always on or off;
❒Zto speed up demisting/defrosting of the front
windows, rear window and door mirrors.During fully automatic system operation, you can change
the set temperature, air distribution and fan speed at
any time by using the relevant buttons or knobs: the
system will automatically change its settings to adjust to
the new requirements. During fully automatic operation
(FULL AUTO), the word FULL will disappear if the air
distribution and/or flow rate and/or engagement of the
compressor and/or recirculation settings are changed.
In this way, the functions will switch from automatic to
manual control until the AUTO button is pressed again.
With one or more functions turned on manually, the
adjustment of the intake air temperature continues to
be managed automatically, except with the compressor
switched off: if this is the case, the temperature of the
air introduced into the passenger compartment cannot
be lower than that of the outside air.
CONTROLS
Air temperature adjustment knob
air (l)
Turn the knob either clockwise or
anticlockwise to increase or lower the
requested temperature in the passenger
compartment.
The temperature set is shown on the display.
Turn the knob either fully to the right or fully to the left
to the extreme HI or LO position to turn the maximum
heating or maximum cooling functions on:
❒HI Function (maximum heating):
select by turning the temperature knob clockwise
beyond the maximum value (32 °C).

278
KNOWING
YOUR CAR
SAFETY
STARTING
AND
DRIVING
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
MAINTENANCE
AND CARE
TECHNICAL
SPECIFICATIONS
INDEX
– headlight alignment
corrector ............................. 107
Headlights (warning
for cleaning) ............................ 225
Heated rear window ............... 80
Heating and ventilation ...........45
– automatic climate control ... 54
– controls ................................ 46
– front window rapid
defrosting/demisting ...48-51-59
– heated rear window and
external rear view mirrors
defrosting/demisting .... 48-53
– interior air recirculation ... 49
– manual climate control ..... 49
– passenger compartment
air vents ............................... 46
Heavy use of the vehicle
(servicing) ................................ 208
Hill Holder system .................. 111
Identification plates ................. 227
– body paintwork .................. 228
– identification data ............... 227Ignition switch .......................... 12
– steering lock ........................ 13
In an emergency ....................... 169
Installation of electrical/
electronic devices .................. 121
Installing the tow hook ........... 151
– assembly diagrams....... 153-154
Interior fittings ......................... 84
Interiors (maintenance) .......... 225
“Isofix” child seat ..................... 134
Keys ........................................... 5
– Code card ........................... 5
– key with remote control .. 6
– key without remote
control ................................. 8
– replacing the battery ......... 8
Knowing your car .................... 3
Light clusters
– front (bulb replacement) .. 184
– rear (bulb replacement) ... 189
Load (warnings) ....................... 147
Load advice................................ 147Load compartment button .... 108
Load limiters ............................. 127
Lubricants (quantity and
products) .........................263-264
Main beam headlights
– bulb replacement ............... 185
– control ................................. 68
Main beam headlights
– bulb replacement ............... 185
– control ................................. 68
– flashing the headlights ....... 69
Maintenance and care ............. 205
– regular checks ..................... 208
– Scheduled servicing ........... 205
– Scheduled Servicing
Plan ...................................206-207
–Heavy use of the vehicle .... 208
Manual climate control ........... 49
Moving platform........................ 101
MSR (system) ............................ 112
MSR system................................ 112
Multifunction display ............... 18