2012 Citroen DS4 check engine

213Driving
System which keeps your vehicle immobilised
temporaril
y (approximately 2 seconds) whenstarting on a gradient, the time it takes to move your foot from the brake pedal to the
accelerator pedal.
This function is onl
y active when:


- t
he vehicle is completely stationary, with your foot on the brake pedal,

- when cer tain conditions of gradient are met,

- with the driver’s door closed.
The hill start assist function cannot bedeactivated.






Hill start assist
On an ascending slope, with the vehicle
stationary, the vehicle is held for a brief moment when you release the brake pedal:- if you are in first gear or neutral with a
manual gearbox,
- if you are in position A
or Mwith the electronic gearbox system,
- if you are in position D
or Mwith an
automatic gearbox.
Operation

Operatin
g fault

If a fault occurs with the system, these warninglamps come on. Contact a CITROËN dealer or a qualified workshop to have the system
checked.


Do not leave the vehicle while it is being held in the hill star t assist phase.
If you need to leave the vehicle whilethe engine is running, apply the parking brake manually then ensure that theparking brake warning lamp is on (notflashing) in the instrument panel.On a descending slope, with the vehicle
stationar
y and reverse gear engaged, thevehicle is held for a brief moment when you
release the brake pedal.

The system is reactivated automaticallyat every new star t using the key.
Reactivation

This system requires a specific battery with aspecial specification and technology (reference numbers available from a CITROËN dealer or a qualified workshop).
Fitting a battery not listed by CITROËN
introduces the risk of malfunction of the system. In the event of a malfunction with the s
ystem,
the "ECO OFF"switch warning lamp flashes,
then comes on continuously.
Have it checked by a CITROËN dealer or aqualified workshop.


Operating fault
Maintenance

Before doing anything under the bonnet, deactivate the Stop & Start system to avoid any risk of injury resulting from automatic operation of STA R T mode.

The Stop & Star t system makes use of advanced technology. All work on this type of battery must be done only by a CITROËN dealer or a qualifiedworkshop. Pr
ess the "ECO OFF"switch again.
The system is active again; this is confirmed
by the switch warning lamp going off and the
display of a message.
In the event of a fault in STOP mode, thevehicle may stall. All of the instrumentpanel warning lamps come on.Depending on version, an alert message may also be displayed askingyou to put the gear lever into position Nand put your foot on the brake pedal.
It is then necessary to switch off the ignition, then restart the engine using the key.

Blind spot sensors
of the presence of another vehicle in the blind spot angle of their vehicle (areas masked from
the driver's field of vision), as soon as thispresents a potential danger.

Operation


This system is designed to improve safety when driving and is in no circumstances a substitute for the use of the interior rear view mirror and door mirrors. It is the driver'sresponsibility to constantly check the traffic, to asses the distances and relative speeds of other vehicles and to predict their movements before deciding whether to change lane.
The blind spot sensor system can never replace the vigilance and responsibility of thedriver.

)On switching on the ignition, or enginerunning, press this button to activate the function; the warning lamp comes on.
Sensors fitted in the front and rear bumpers
monitor the blind spots. A warnin
g lamp appears in the door mirror on
the side in question:


- immediatel
y, when being overtaken,

- after a delay of about one second, whenover taking a vehicle slowly.

233Checks











Bonnet


Opening
)Open the front left door.)Pull the interior bonnet release lever A ,
located at the bottom of the door aperture.
) Push the exterior safety catch Bto the leftand raise the bonnet.
)
Unclip the stay C
from its housing on the back of the bonnet. )
Fix the stay in the notch to hold the bonnet open.


The location of the interior bonnet release lever prevents opening of the bonnet while the front left door isclosed.


Do not open the bonnet in high winds. When the engine is hot, handle theexterior safety catch and the bonnet
stay with care (risk of burns).
Before doing anything under the bonnet, switch off the Stop & Startsystem to avoid any risk of injury
resulting from an automatic change toSTA R T m o d e .


Closing
)
Take the stay out of the support notch. )
Clip the stay in its housing on the back of
the bonnet.) Lower the bonnet and release it at the endof its travel. )
Pull on the bonnet to check that it is secured correctly.

235
Checks














Petrol engines

The various caps and covers allow access for
checking the levels of the various fluids and for
replacing cer tain components.
1. Power steering reservoir.2.Screenwash and headlamp wash reservoir.3.Coolant reservoir.4.
Brake fluid reservoir.
5. Battery/Fuses.
6.Fusebox.
7. Air filter.8.Engine oil dipstick.9.
Engine oil filler cap.

Diesel engines
The various caps and covers allow access for
checking the levels of the various fluids, for replacing cer tain components and for primingthe fuel system.
1.
Power steering reservoir.2.
Screenwash and headlamp wash reservoir.3.
Coolant reser voir. 4.
Brake fluid reservoir.5.
Battery/Fuses.
6.Fusebox.7. Air filter.8.Engine oil dipstick. 9.
Engine oil filler cap.10.Priming pump *
. 11.
Bleed screw *
.
*
Accordin
g to engine.

237
Checks

























Checking levels
Check all of these levels regularly and top them up if necessary, unless other wise indicated.
If a level drops si
gnificantly, have the corresponding system checked by a CITROËN dealer or a qualified workshop.


Oil level
Engine oil change
Refer to the servicing booklet for the inter val for
this operation.
In order to maintain the reliabilit
y of the engine and emission control system, the use of additives in the engine oil is prohibited.
Oil specifi cation
The oil must correspond to your engineand conform to the manufacturer'srecommendations.



Brake fluid level


Changing the fl uid

Refer to the servicing booklet for the inter val for
this operation.

Fluid specifi cation

The brake fluid must conform to themanufacturer's recommendations and meet theDOT4 standard.
Th
e brake fluid level should be closeto the "MA X" mark. If it is not, check
the brake pad wear.
The reading will only be correct if the
vehicle is on level ground and the engine
has been off for more than 30 minutes. The check is carried out either when
the ignition is switched on using the oil levelindicator in the instrument panel, or using the dipstick.
When working under the bonnet, take care, as cer tain areas of the engine may be extremely hot (risk of burns).
It is normal to top up the oil level
between two services. CITROËN recommends that you check the oillevel, and top up if necessary, every 3 000 miles (5 000 kilometres).

Changing the coolant
The coolant does not have to be changed.


Coolant specifi cation

The coolant must conform to the
manufacturer's recommendations.

Coolant level
The coolant level should be close
to the "MA X" mark but should never exceed it. When the engine is warm, the
temperature of the coolant is regulated by the fan. This can operate with the ignition off.
On vehicles which are fitted with a par ticle
emission filter, the fan may operate after
the vehicle has been switched off, even if
the en
gine is cold.
In addition, as the cooling system is pressurised,
wait at least one hour after switching off the engine before carrying out any work.
To a v o i d a ny risk of scalding, unscrew the cap by two turns to allow the pressure to drop. When the pressure has dropped, remove the cap and top up the level.
Power steering fluid level
The power steering fluid level should
be close to the "MA X" mark. Unscrew
the cap, with the engine cold, tocheck the level. To check the level or top up the
fluid on vehicle fitted with headlamp
washers
, immobilise the vehicle and switch of the engine.

Screenwash/headlamp wash
level