Page 5 of 252
3
CONTENTS
Direction indicators 103Hazard warning lamps 103Horn 103Emergency or assistance call 104Braking assistance systems 104Trajectory control systems 105Front seat belts 106Airbags 108
8 - SAFETY 103 Î111
Parking brake 1126-speed manual gearbox 112Gear effi ciency indicator 113Electronic gearbox 114Automatic gearbox 118Stop & Start 121Hill start assist 124Speed limiter 125Cruise control 127Rear parking sensors 129
9 - DRIVING 112 Î 130
Bonnet 132Running out of fuel (Diesel) 132Petrol engines 133Diesel engines 134Checking levels 135Checks 136
10 - CHECKS131 Î137
Temporary puncture repair kit 138Changing a wheel 143Changing a bulb 147Changing a fuse 153Battery 160Energy economy mode 162Changing a wiper blade 162Towing the vehicle 163Towing a trailer 165Audio pre-equipment 166Accessories 167
11 - PRACTICAL
INFORMATION 138 Î168
Petrol engines 169Petrol weights 170LPG engines 172LPG weights 173Diesel engines 174Diesel weights 176Dimensions 178Identifi cation markings 179
12 - TECHNICALD ATA 169 A Î 180
VISUAL
SEARCH237 Î 240
ALPHABETICALINDEX 241 Î 244
AUDIOandTELEMATICS 181 Î 236
Emergency or assistance 181MyWay 183Audio system 215
Page 95 of 252
6
93
FITTINGS
REAR PARCEL SHELF
To remove the shelf:
)
unhook the two cords,
)
raise the shelf slightly, then unclip it
on each side.
HOOKS
The hooks can be used to hold shop-
ping bags.
STORAGE BOX
)
Raise the boot carpet by pulling the
strap upwards to gain access to the
storage box.
This has areas for storing a temporary
puncture repair kit, a box of spare bulbs,
a fi rst aid kit, two warning triangles, ...
)
refi t the boot fl oor carpet by folding it
slightly in the middle.
Page 149 of 252
11
147
PRACTICAL INFORMATION
The headlamps are fi tted with
polycarbonate glass with a pro-
tective coating:
)
do not clean them using a
dry or abrasive cloth, nor
with a detergent or solvent
product,
)
use a sponge and soapy water,
)
when using a high pressure
washer on persistent marks,
do not keep the lance direct-
ed towards the lamps or their
edges for too long, so as not
to damage their protective
coating and seals.
CHANGING A BULB
)
Do not touch the bulb directly with your fi ngers, use lint-free
cloths.
Changing a bulb should only be
done after the headlamp has
been switched off for a few min-
utes (risk of serious burns).
It is imperative to use only anti-
ultraviolet (UV) type bulbs in
order not to damage the head-
lamp.
Always replace a failed bulb with
a new bulb with the same type
and specifi cation.
Front lamps
1.
Direction indicators
(PY 21 W amber).
2.
Sidelamps (W 5 W).
3.
Main beam headlamps (H1-55 W).
4.
Dipped beam headlamps
(H7-55 W).
5.
Front foglamps (PSX 24 W).
Page 150 of 252
11
148
PRACTICAL INFORMATION
Changing direction indicator bulbs
)
Turn the bulb holder a quarter of a
turn and extract it.
)
Pull out the bulb and change it.
To r efi t, carry out these operations in
reverse order.
When refi tting, close the protec-
tive cover carefully to preserve
the sealing of the headlamp.
Rapid fl ashing of the direction
indicator warning lamp (right
or left) indicates the failure of a
bulb on that side.
Amber coloured bulbs, such as
the direction indicators, must be
replaced with bulbs of identical
specifi cations and colour.
Changing dipped beam headlamp
bulbs
)
Remove the protective cover by
pulling on the tab.
)
Disconnect the bulb connector.
)
Spread the springs to release the
bulb.
)
Pull the bulb out and change it.
To r efi t, carry out these operations in re-
verse order.
Changing main beam headlamp
bulbs
)
Remove the protective cover by
pulling on the tab.
)
Disconnect the bulb connector.
)
Spread the springs to release the
bulb.
)
Remove the bulb and change it.
To r efi t, carry out these operations in
reverse order.
Changing sidelamp bulbs
)
Remove the protective cover by
pulling on the tab.
)
Pull the bulb holder pressing on the
tabs on both sides.
)
Pull the bulb and change it.
To r efi t, carry out these operations in
reverse order.
Page 151 of 252
11
149
PRACTICAL INFORMATION
Changing front foglamp bulbs
To obtain a replacement module,
contact your CITROËN dealer or
a qualifi ed workshop.
If you experience any diffi culty
in replacing bulbs, contact your
CITROËN dealer or a qualifi ed
workshop.
)
Access to the front foglamp is through
the aperture below the bumper.
)
Disconnect the black bulb holder
connector, by pressing on the tab at
the top.
)
Remove the bulb-holber by press-
ing on the 2 clips (at the top and the
bottom).
)
Replace the module.
To r efi t, carry out these operations in
reverse order.
Changing integrated direction
indicator side repeaters
)
Insert a screwdriver towards the
centre of the repeater between the
repeater and the base of the door
mirror.
)
Tilt the screwdriver to extract the re-
peater and remove it.
)
Disconnect the repeater connector.
)
Replace the module.
To r efi t, carry out these operations in
reverse order.
Contact a CITROËN dealer or a
qualifi ed workshop to obtain a re-
placement side repeater module.
Page 152 of 252
11
150
PRACTICAL INFORMATION
Rear lamps
1.
Brake/sidelamps (P21/5W).
2.
Direction indicators
(PY21W amber)
3.
Foglamp, right-hand side
(PR21W red)
Reversing lamp, left-hand side
(P21W).
These four bulbs are changed from in-
side the boot:
)
open the boot,
)
remove the access fl ap from the
corresponding side trim panel,
)
unscrew the butterfl y nut securing
the lamp unit,
)
unclip the lamp unit connector,
)
extract the lamp unit carefully pulling
in its middle towards the outside,
)
spread the four tabs and remove the
bulb holder,
)
turn the bulb a quarter of a turn and
change it.
To r efi t, carry out these operations in re-
verse order.
Take care to engage the lamp unit in its
guides, while keeping it in line with the
vehicle.
Changing bulbs
Amber or red bulbs, such as
those for the direction indica-
tors and rear foglamp, must be
replaced by bulbs of the same
rating and colour.
The lamps on the tailgate are
dummy units. They are there for
aesthetic purposes only.
Page 153 of 252
11
151
PRACTICAL INFORMATION
Changing the number plate lamp
bulbs (W5W)
)
Insert a thin screwdriver into one of
the outer holes of the lens.
)
Push it outwards to unclip.
)
Remove the lens.
)
Pull the bulb out and change it.
)
Open the boot.
)
Remove the plugs A
on the inner
panel.
)
Push on the centre of the lamp
using two screwdrivers to lever it
outwards.
)
Disconnect the connector and if
necessary the screenwash pipe
from the lamp.
)
Turn the bulb holder for the faulty
bulb a quarter of a turn.
)
Pull out the bulb and change it.
To r efi t, carry out these operations in
reverse order.
Third brake lamp (4 W5W bulbs)
Page 154 of 252
11
152
PRACTICAL INFORMATION
Interior lighting
Interior lamp (1/W5W)
Unclip the cover of the interior lamp 1
with a thin screwdriver, close to the but-
ton, to access the faulty bulb.
Side reading lamps (2/W5W)
Unclip the cover of the reading lamp 2
with a small screwdriver at the switch
end for access to the faulty bulb.
Boot lamp (W5W)
Unclip the unit by pushing it from the
rear.
Central storage lamps (W5W)
Unclip the lamp for access to the bulb.
