2012 Citroen C CROSSER Button a
[x] Cancel search: Button aPage 108 of 244
VI
SAFETY
106
Front seat belt not fastened/
unfastened warning lamp
When the ignition is switched
on, this warning lamp comes
on accompanied by an au-
dible signal for a few seconds
if the driver has not fastened
their seat belt.
Rear seat belts
Each rear seat is fi tted with a three-point
inertia reel seat belt with force limiter.
Fastening
)
Pull the strap, then insert the tongue
in the buckle.
)
Check that the seat belt is fastened
correctly by pulling the strap.
Unfastening
)
Press the red button on the buckle.
If the driver does not fasten their seat
belt within one minute after switching on
the ignition, the warning lamp fl ashes
accompanied by an intermittent audible
signal and a display on the instrument
panel screen.
The warning lamp, the audible signal
and the display stop after approximate-
ly 90 seconds and return until the driver
fastens their seat belt.
If the seat belt is unfastened while the
vehicle is moving
, you are alerted by
the same warnings.
Storing after use
1.
Pass the seat belt under the support A
located on each rear side pillar,
2.
Insert the tongue in the slot B
of the
support.
Rear buckles
)
Store the buckles in the locations A
and B
provided for this purpose in
the rear seat cushion.
Driver's seat belt
Outer rear seat belts
Front passenger's seat belt
When the ignition is switched on, this
warning lamp comes on the centre
console panel.
It is accompanied by an audible signal
for a few seconds if the passenger has
not fastened their seat belt.
If the seat belt is unfastened while the
vehicle is moving
, you are alerted by
the same warnings.
Page 114 of 244
VII
DRIVING
11 2
PARKING BRAKE
Releasing
)
Pull the lever up and press the button
A
to release the parking brake.
5-SPEED MANUAL GEARBOX
Engaging 5 th or 6 th gear
)
Move the gear level fully to the right
to change to 5 th or 6 th gear.
Applying
)
Pull the parking brake lever up to
immobilise your vehicle.
When parking on a slope, direct your
wheels towards the pavement and apply
the parking brake.
When the vehicle is being
driven, the display of this
message indicates that the
parking brake is still on or has
not been properly released.
6-SPEED MANUAL GEARBOX
Engaging reverse
)
Lift the sleeve below the gear knob
and move the gear lever to the left
and then towards the front.
Reverse gear can only be engaged
when the vehicle is stationary with
the engine idling.
Page 123 of 244
VII
DRIVING
121
Programming
)
Press button 1
.
)
Set the programmed speed by ac-
celerating to the required speed,
then press button 2 "COAST SET"
.
CRUISE CONTROL
The controls of this system are grouped
together on the steering wheel.
1.
"ON/OFF"
button: activation / deac-
tivation of the cruise control mode.
2.
"COAST SET"
button: storing of a
driving speed and decreasing of the
cruising speed.
3.
"ACC RES"
button: increasing of
the cruising speed and recalling of
the stored speed.
4.
"CANCEL"
button: switching off of
the cruise control.
When you press button 1
, the "CRUISE"
indicator comes on in the instrument
panel.
Steering mounted controls Display on the instrument panel
The cruise control cannot, in any cir-
cumstances, take the place of the
need to comply with speed limits or
of the vigilance and responsibility of
the driver.
System which automatically maintains the
vehicle speed at the value programmed
by the driver, without any action on the
accelerator pedal.
The cruise control is switched on
man-
ually: the vehicle speed must be 25 mph
(40 km/h) minimum and second gear
must be engaged in the case of a man-
ual gearbox.
The cruise control is switched off
man-
ually, by an action on the brake or clutch
pedal or if the ASC system is triggered.
The programmed speed can be ex-
ceeded temporarily by pressing the ac-
celerator pedal.
To return to the programmed speed,
simply release the accelerator pedal.
Switching off the ignition cancels any
programmed speed value.
Page 124 of 244
VII
!
122
When the cruise control is in
operation, pay attention if you
press and hold one of the pro-
grammed speed adjustment buttons:
this can result in a very rapid change
in the speed of your vehicle.
Do not use the cruise control on slip-
pery roads or in heavy traffi c.
On a steep descent, the cruise control will
not be able to prevent the vehicle from
exceeding the programmed speed.
To prevent the mat from becoming
caught under the pedals:
- ensure that the mat is positioned
correctly,
- never fi t one mat on top of another.
To deactivate the cruise control:
)
Press the brake
or clutch
pedal, or
)
Press button 1 "ON OFF"
, or
)
Press button 4 "CANCEL"
.
The cruise control may be deactivated
automatically:
)
When the vehicle reaches a speed
below 20 mph (35 km/h).
)
When the active stability control system
(ASC) comes into operation.
Reactivating the function
When the cruise control has been de-
activated, you can return to the stored
speed by pressing button 3 "ACC RES"
when you reach a minimum speed of
25 mph (40 km/h).
Decreasing the programmed
speed
)
Using button 2 "COAST SET"
:
- successive presses decrease the
speed in steps of approximately
1 mph (1.6 km/h).
- a maintained press of this button
decreases the speed progressively.
Once the speed required has been
reached, release the button, the new
speed is stored.
)
Using the brake pedal:
- brake to deactivate the cruise control,
then press button 2 "COAST SET"
.
Release to store the new speed.
Temporary acceleration/deceleration
Increasing the programmed
speed
)
Using button 3 "ACC RES"
:
- successive presses increase the
speed in steps of approximately
1 mph (1.6 km/h).
- a maintained press of this button
increases the programmed speed
progressively.
Once the speed required has been
reached, release the button, the new
speed is stored.
)
Using the accelerator pedal:
- accelerate to reach the speed re-
quired, then press button 2 "COAST
SET"
. Release the button to store
the new speed.
Temporary acceleration
Press the accelerator pedal as normal.
When the pedal is released, you return
to the stored speed.
Temporary deceleration
Press the brake pedal to reduce the
speed. To return to the stored speed,
press button 3 "ACC RES"
.
Page 126 of 244
VII
DRIVING
124
REVERSING CAMERA
Linked with the navigation option, a
reversing camera is activated automati-
cally when reverse gear is engaged.
The colour image is provided on the naviga-
tion screen with indication of the limit of the
rear bumper and of the general direction of
the vehicle.
Operating fault
If an operating fault occurs, the indicator
lamp in button A
fl ashes when reverse
gear is engaged.
Contact a CITROËN dealer or a qualifi ed
workshop.
In bad weather or in winter, check
that the sensors are not covered with
mud, ice or snow.
Deactivation
)
With reverse gear engaged, press
button A
, the indicator lamp goes
off, the system is fully deactivated.
Reactivation
)
With reverse gear engaged, press
button A
again, the indicator lamp
comes on, the system is reactivated.
Modifi cation of the detection zones
)
Press button A
to deactivate the
system.
)
Press button A
again for a few seconds
and release it.
The detection zone modifi cation information
is indicated by an audible signal:
- double
signal on vehicles fi tted with
a towbar,
- single
signal on vehicles which are
not fi tted with a towbar.
The red line indicates the distance re-
quired to open the lower tailgate.
Page 134 of 244
IX
!
PRACTICAL INFORMATION
132
CHANGING A WHEEL
1.
Wheelbrace.
Used to remove the wheel trim and
the wheel fi xing bolts.
2.
Jack.
Used to raise the vehicle.
3.
Handle.
Used to extend the jack.
4.
Removable towing eye.
Refer to the "Towing" paragraph.
Other accessories
Wheel with trim
When removing the wheel
, remove
the trim fi rst using the handle 3
, pulling
at the notch.
When refi tting the wheel
, refi t the trim
starting by placing its notch F
(indicated
on the back of the trim) opposite the
valve G
and press on its outer edge
with the palm of your hand.
List of tools
When changing a wheel, ensure
that the four wheels are of identi-
cal specifi cation and brand. When storing, take care to secure
the tool bag D
fi rmly using the fi xing
band C
.
Access to the tools
The tools are stored in the storage
compartment in the boot right-hand trim.
To gain access to them:
)
open the boot,
)
turn button A
to the left,
)
remove the cover B
,
)
remove the fi xing band C
and take
out the tool bag D
containing the
tools,
)
take the jack E
in your hand and re-
move it from its fi xing position.
Page 156 of 244
IX
!
PRACTICAL INFORMATION
154
TOWING
Access to the tools
Having your vehicle towed on a flatbed
)
Below the front bumper, install the
towing system on the towing eye 1
.
The towing eye and the tools are stored
in the storage compartment in the right-
hand boot trim.
To gain access to them:
)
open the boot,
)
turn button A
to the left,
)
remove the cover B
,
)
remove the fi xing band C
and take out
the tool bag D
containing the tools,
)
take the towing eye and the tools re-
quired out of the tool bag.
Place the gear lever in neutral.
Always have the vehicle
towed on a fl atbed.
Never have the vehicle towed with
the four wheels on the ground, this
could damage the transmission.
The vehicle must not be towed with
the front or rear wheels on the ground
even if it is in front "2WD" (2 wheel
drive) mode.
Page 168 of 244
XI
166
AUDIO and TELEMATICS
STEERING MOUNTED CONTROLS
1.
On/Off and selection of
radio or
CD mode
2.
Volume decrease
3.
Volume increase
4.
Search for a higher radio frequency/
Next track/Fast forwards play
5.
Search for a lower radio frequency/
Previous track/Fast backwards play
Switching off
Press button 1
for more than two seconds.
Selecting the source
Press button 1
.
The source changes in the following order: FM1/FM2/FM3/MW/LW/CD/FM1...
Searching in radio mode
Press button 4
or 5
to search for a
higher or lower radio frequency respec-
tively.
Searching in CD mode
Press button 4
or 5
to select the next or
previous track on the CD respectively.
Press and hold button 4
or 5
for fast for-
wards or fast backwards playing of the
current track of the CD respectively.
Switching on
Press button 1
for more than two seconds.
The last source selected before switching
off comes back into operation.
Adjusting the volume
Press and hold button 2
or 3
to decrease
or increase the volume respectively. While a track is being played, press
button 5
once to return to the beginning
of this track.
They can be used when the ignition
switch is in the "ON" or "ACC" position.