2012 AUDI R8 SPYDER remove seats

you do this while the vehicle is moving,
you will be out of position. Always adjust the driver's or front passenger seat when
the vehicle is not moving .
- Be careful when adjusting the seat
height. Check to see that no one is in the
way, or serious injury could result!
- Because the seats can be electrically ad­
justed with the ignition key removed,
never leave children unattended in the
vehicle . Unsupervised use of the e lectr ic
seat adjustments may cause serious in­
jury .
- To reduce the risk of injury in the case of
sudden braking or accident, front pas­
sengers must neve r ride in a moving ve­
hicle with the seatback reclined. Safety
belts and the airbag system offer maxi ­
mum protection on ly when the seatback
is upright and the safety belts are prop­
erly posit ioned on the body. The more
the seatback is reclined, the greater the risk of personal injury from an incorrect
seating posit ion and improperly posi­
tioned safety belts!
- Always make sure the front seatbacks are
in the upright position when dr iv ing .
Head restraints
Adjusting head restraints
Fig. 7 4 Adjusting head restra ints
The head restraints can be adjusted to provide
safe support to head and neck at the optimum
h e ight. When optimally adjusted, the top of
the restraint shou ld be level with the top of
the head . If that is not possible, try to adjust
S ea ts a nd s to rage 61
the head restraint so that it is as close to this
position as possible¢
page 94.
1-Grasp the sides of the head restraint with
both hands and slide it upward/downward
until you fee l it click into place
¢ fig . 74.
& WARNING ~ -
-Driving without head restraints or with
head restra ints that are not properly ad­
justed increases the risk of ser ious or fa­
tal neck injury dramat ically.
- Read and heed all WARNINGS
¢page 94.
@ Tips
Correct ly adjusted head restraints and
safety be lts are an extreme ly effective
combination of safety features.
Cup holder
F ig. 75 Cup holder
A WARNING
0 U)
~ ., a,
-
Spilled hot liquid can cause an accident
and personal injury.
- Never carry any beverage containers with
hot liq uids, such as hot coffee or hot tea,
in the vehicle while it is moving. In case
of an acc ident, sudden braking or other
veh icle movement, hot liquid could spill,
causing scalding burns. Spilled hot liquid
can also cause an accident and personal
lnJU ry.
- Use only soft cups in the cupholder . Hard
cups and glasses can cause injury in an
accident.

62 Seats and storage
- Never use the cupho lder or adapter as an
ashtray- risk of f ire.
CD Note
On ly drink containe rs with lids should be
carried in the cupho lder. Liquid could spill
out and damage your vehicle's e lectronic
equ ipment or sta in the upholstery, etc.
Ashtray
Fig . 76 Center console: ashtray
The asht ray is inserted in the cupholder.
Opening the ashtray
.,. Fold the cover upward .
Emptying the ashtray
.,. Lift the closed ashtray up o ut o f the cu­
pholder.
A WARNING
Never put waste paper in the ashtray. Hot
ashes or other hot objects in the ashtray
could set waste paper on fire.
Cigarette Lighter/
socket
N
-"' 0 ..:. ... m
The c igarette lig hte r or socket only wo rk with
the ign ition on.
Using the cigarette lighter
.,. Slide the cover open to reach th e cigarette
lighter
qpage 62.
.,. Push the knob in.
.,. Wait un til the c igarette lighte r knob pops
out. .,.
Remove the cigarette lighter immediately
and use it.
.,. Reinsert cigarette lighter into the socket af ­
ter use.
Connecting an appliance
.,. Slide the cover open to reach the c igarette
lighter .
.,. Remove cigarette lighter .
.,. Plug in appliance to be used.
T he socket of the c igarette lighter may be
u sed for 12-volt appliances with maximum
consumption of up to 100 watts, such as a
flash light, small vacuum cleaner, etc.
A WARNING
--Improper use of the c igarette lig hter can
cause serious injury or start a fire .
- Be careful when using the c igarette light­
er. If you do not pay attention to what
you are doing when you are us ing t he cig­
arette lighter you can burn yo urself.
CD Note
-To avoid damaging the socket, only use
plugs that fit properly.
- Only use the cigarette lighter socket as a
powe r source for e lectr ica l accessories
for short durations . Use t he sockets in
the vehicle when a power source is need­ ed for longer du rat ions .
(0 Tips
-When the eng ine is off and accessories
are st ill plugged in and are on, t he vehi­
cle battery can still be d ra in ed.
- The ve hicle battery must not be charged
w ith a standard small charger that pl ugs
into the cigarette lighter or outlet .
Storage
, General
A WARNING
- Always remove objects from the instr u­
men t pa nel. A ny items not put away
-

-Never remove the upholstery from the
front passenger seat.
- Never disassemble or remove parts from
the seat or disconnect wires from it.
- Never carry sharp objects in your pockets
or place them on the seat. If the weight­
sensing mat in the passenger seat is
punctured it cannot work properly.
- Never carry things on your lap or carry
objects on the passenger seat. Such
items can increase the weight registered
by the weight-sensing mat and send the
wrong information to the airbag control
unit.
- Never store items under the front pas­
senger seat. Parts of the Advanced Air­
bag System under the passenger seat
could be damaged, preventing them and
the airbag system from working proper­ ly.
- Never place seat covers or replacement
upholstery that have not been specifical­
ly approved by Audi on the front seats.
- Seat covers can prevent the Advanced
Airbag System from recognizing child re­
straints or occupants on the front pas­
senger seat and prevent the side airbag
in the seat backrest from deploying prop­
erly.
- Never use cushions, pillows, blankets or
similar items on the front passenger
seat. The additional padding will prevent
the weight-sensing mat in the seat from
accurately registering the child restraint
or person on the seat and prevent the
Advanced Airbag System from function­ ing properly.
- If you must use a child restraint on the
front passenger seat and the child re­
straint manufacturer 's instructions re­
quire the use of a towel, foam cushion or
something else to properly position the
child restraint, make certain that the
PASSENGER AIR BAG OFF light comes
on and stays on whenever the child re­
straint is installed on the front passen­
ger seat .
Airbag system 117
-If the PASSENGER AIR BAG OFF light
does not come on and stay on, the inflat­
ing airbag will hit the child safety seat or
infant carrier with great force and will
smash the child safety seat and child
against the backrest, door or roof. Have
the airbag system inspected immediately by your authorized Audi dealer .
How the Advanced Airbag System
components work together
The front Advanced Airbag System and the
side airbags supplement the protection of­
fered by the front three-point safety belts
with pretensioners and load limiters and the
adjustable head restraints to help reduce the
risk of injury in a wide range of accident and
crash situations. Be sure to read the impor­
tant information about safety and heed the
WARNINGS in this chapter.
Deployment of the Adv a need Airbag System
and the activation of the safety belt preten­
sioners depend on the deceleration measured
by the crash sensors and registered by the
electronic control unit. Crash severity depends
on speed and deceleration as well as the mass
and stiffness of the vehicle or object involved
in the crash.
When the electronic control unit registers a
low severity crash and the safety belt is being
used, the airbag will not deploy. If the safety
belt is not being used, the first stage deploys,
followed by the second stage after a much lat­
er time in the crash sequence.
If the electronic control unit registers a crash
of medium severity, the first stage of the air­
bag deploys followed by the second stage at a
much later time in the crash sequence - re­
gardless of whether the safety belt is being
used or not . In higher severity crashes as reg­
istered by the electronic control unit, both the
first and second stages deploy almost at the
same time .
On the passenger side, regardless of safety
belt use, the airbag will be turned off if the
weight on the passenger seat is less than the
IJII,-
•
•

Plastic parts and imitation leather
You can clean plastic parts and imitation
leather with a damp cloth . If this does not re­
move the dirt, you can treat these parts only
with specia l
solvent-free plastic cleaning and
care products.
A WARNING
So lvents can change the properties of
some plast ics and make it harder for the
airbag to dep loy.
-
- Never clean the instrument panel or the
surface of Airbag modules with cleaning
products that contain solvents.
- Products containing solvents w ill make
the surface of this part porous.
- Serious injur ies can result if plastic parts
come loose when the airbag is deployed.
- Always read and heed all WARNINGS and
the informat ion
c::;,page 153.
(D Note
Clean ing agents containing solvents will
attack the material and can change the
way it behaves.
Carbon-fiber parts
Applies to vehicles: with carbo n-fiber parts
The carbon-fiber parts of your vehicle have a
pa inted surface. They do not require any spe­
cial care and are cleaned like plast ic parts
¢pag e 159.
Fabrics and fabric coverings
Fabrics and fabr ic coverings (e.g. seats, door
trim panels, etc.) should be cleaned at regular
intervals with a vacu um cleaner. This removes
surface dirt particles which could become em­
bedded in the fabric through use. Steam
cleaners shou ld not be used, because the
steam tends to push the dirt deeper into the
fabric and lock it there.
Cleaning and protection 159
Normal cleaning
Generally, we recommend using a soft sponge
or a lint-free microfiber cloth to the clean fab­
ric. Brushes shou ld only be used for carpets
and floor mats, since other fabric surfaces could be harmed by brushes.
Normal surface stains can be cleaned using a
commercially available foam cleaner . Spread
the foam on the s urface of the fabric with a
soft sponge and work it in gently. Do not satu­
rate the fabric. Then pat the foam dry using
absorbent, dry cloths (e.g. m icrofiber cloth)
and vacuum it after it has dried completely.
Cleaning stains
Stains caused by beverages (e.g. coffee, fruit
juice , etc.) can be treated with a mild deter­
gent solution. Apply the detergent solution
with a sponge . In the case of stubborn stains,
a detergent paste can be applied directly to
the stain and worked into the fabric. After­
wards, use copious amounts of clean water to
remove the remaining deterge nt. Apply the
water with a damp doth or sponge and pat
the fabric dry with an absorbent, dry cloth .
Stains from chocolate or makeup should have
detergent paste (e.g. ox-gall soap) rubbed in­
to them. Afterwards, remove the soap with
water (damp sponge) .
Alcohol can be used to treat stains from
grease, oil, lipstick or a ballpoint pen. Melted
grease or dye must be patted off using ab­
sorbent materia l.
It may be necessary to re ­
treat the areas with detergent paste and wa­
ter.
In the case of general soiling of the upho ls­
tery and cover material, we recommend hiring
a specia list t hat has the equipment to clean
the seat covers and other fabr ic surfaces by
shampooing and spray extraction.
A WARNING
Always read and heed all WARNINGS and
the information
c::;, page 153.
•
•

160 Cleaning and protection
Open Velcro fasteners on your clothing can
damage the seat cover. Please make sure
that Velcro fasteners are closed.
Natural leather
App lies to vehicles: with natura l leather
Audi makes great efforts to maintain the
properties, natural look and feel of interior leather.
General
We offer many different types of leather on
our vehicles. Most are different types of nappa
leather, which has a smooth surface and
comes in various colors.
The intensity of the color determines the visu­
al characteristics and appearance . If the sur­
face of the leather has a typical natural look,
then the leather is a nappa leather that has
been left in a relatively natural condition. This
leather offers particularly good comfort and
breathes well. Fine veins, closed grains, insect
bites, skin folds, and subtle variations in color
remain visible. These characteristics demon­
strate that the material is natural.
Natural nappa leather is not covered by a col­
or finish.
It is therefore more sensitive to soil­
ing and wear, which is something you need to
consider if children, animals or other factors
might prove to be particularly hard on the
l eather.
By contrast, leather types that are covered by
a colored finish layer are more durable. This
has a positive effect on the leather's resist­
ance to wear and soiling in daily use. On the
other hand, the typical characteristics of natu­
ral leather are barely or not apparent. Howev­
er, this does not mean that the leather itself is of inferior quality.
Care and handling
Because of the exclusive nature of the types of
leather that Audi uses and their unique prop­
erties (such as sensitivity to oils, grease, soil­ ing, etc.), you will need to be somewhat care- ful
with these leathers, and a certain type of
care is required . For example, dark clothing
materials can discolor leather seats (especial ­
ly if such clothing is damp and was not dyed
correctly). Dust and dirt particles in pores,
folds, and seams can have an abrasive effect and can damage the leather surface as well as
weaken seams .
The leather should be cleaned regularly as needed. After having been used for a relatively
long time, your leather seats will acquire a
rich aged finish. This is a characteristic of nat­
ural leather and a sign of true quality.
In order to maintain the value of this natural
product over the life of your vehicle, you
should follow the recommendat ions below:
(D Note
- To keep your leather from bleaching out,
do not allow it to be exposed to bright
sunlight for long periods of time. If you
have to leave the vehicle parked outside
for long periods, cover the leather to protect it from direct exposure to sun­
light.
- Sharp objects on clothing, such as zip­
pers, rivets or sharp pieces on belts can
leave permanent scratches or scrape
marks on the surface of the leather .
(D Tips
-After each time you clean the leather and
at regular intervals, use a leather preser­
vative creme that contains UV-blockers
and that works into the leather. This
creme will nourish and moisturize the
leather, helping it to breathe and stay
supple .
It also helps to build up a protec­
tive coating on the surface.
- Clean the leather every 2 -3 months,
and clean any areas that get soiled .
- Remove fresh marks made by ballpoint
pens, ink, lipstick, shoe polish, etc. as
soon as possible.
- Preserve the color of the leather as need­
ed by using a spec ial colored leather care
creme to touch up areas of uneven color .