2012 AUDI Q7 AMI

this mode. If the suspension is switched from
this mode to another mode, dynamic mode
cannot be re-se lected .
{D) Tips
-For vehicles with a factory installed tow­
ing hitch or a trailer hitch that was in­
stalled later accord ing to factory specifi­
cations, the system recognizes "Trailer
tow ing mode" and activates this special
mode automatically, as soon as the elec­
trical connection on the trailer socket is
connected . The mode ceases automat i­
cally when the elect rical connection to
the trailer socket is d isconnected.
- If the tra iler towing mode has been act i­
vated, the vehicle will not drop to the l ow or highway level.
Cargo mode
A pp lies to vehicles: wit h Adap tive Air S uspe nsio n
The rear of the vehicle con be lowered to
make it easier to load .
Fig. 178 Luggage compa rtment detail: Cargo mode
sw itc h
Using sw itch for activating cargo mode
~ Close all vehicle doors .
~ Open the trunk lid .
~ Press the lower pa rt of the switch@
Q fig. 178. The rear of the vehicle is low­
ered.
~ Press the uppe r part of the sw itch (D . The
rear of the vehi cle is raised aga in .
Activating cargo mode in the MMI*
~ Se lect: Function button ICAR I > Function
button
! SE TUP I> Lower f or load in g. Ad
apti ve A ir Sus pension 155
In cargo mode, the rear ax le is lowered by 2 .2
inches (55 mm), compared to the normal lev­
el.
While the ve hicl e is in ca rgo mode, the seg­
ments do not appear as filled in the segment
display.
Cargo mode is a utomatically c ance led again
when a different mode is selected in the MM I
D isplay, or when a speed of about 3 mph (5
km/ h) has been exceeded.
If the system is tempora rily unavailable due
to, for instance, an empty compressed ai r
tank, the
Lower fo r loading* function appears
greyed out in the MMI Display. As soon as the
system is available again, the function can
once more be selected in the disp lay.
While the vehicle is being lowered, the indica­
tor light @~
fig. 178 on the switch in the
luggage compartment flashes. When the car­
go level has been reached, the indicator light
comes on and remains on as long as the vehi­
cle is in cargo mode. When the vehicle is
raised agai n, the indicator l ight f las hes aga in.
(D Note
Make sure before canceling cargo mode
that there is sufficient clearance above the
vehicle and around the tru nk lid , if open .
(D Tips
-The ve hicle w ill not be lowered if one of
the vehicle doors is open, or if the com­
pressed air tank is empty . T he indicator
light on the switch flashes three times.
- When the compressed air tank is empty,
it will refill when you drive at speeds
over 25 mph (40 km/ h). The vehicle can
be lowered to cargo level when the com­
pressed air tank is adequately fille d.
- If the veh icle is i n lift or off road mode
when you act ivate cargo mode, the vehi­
cl e w ill first drop dow n to norma l level.

166 Driving Safel y
Stowing luggage
Loading the luggage compartment
All luggage and other objects must be prop­ erly stowed and secured in the luggage com ­
partment.
Fig . 184 Safe load pos ition ing: place heavy objects as
low and as far forward as possible.
Loose items in the luggage compartment can
shift suddenly, changing vehicle handling
characterist ics . Loose items can also increase
the r isk of serious personal injury in a sudden
vehicle maneuver or in a collision .
,. Distribute the load evenly in the luggage
compartment .
,. Always place and properly secure heavy
items in the luggage compartment as low
and as far forward as poss ible
¢fig. 184.
,. Secure luggage using the tie-downs provid­
ed
¢ page 80.
,. Make sure that the rear seatback is securely
latched in place .
A WARNING
Improperly stored luggage or other items
can fly through the vehicle caus ing serious
personal inj ury in the event of hard brak­
ing or an acc ident. To help reduce the r isk
of serious persona l injury:
- Always put objects, for example, luggage
or other heavy items in the luggage com­
partment.
- Always secu re objects in the luggage
compartment us ing the tie-down eye lets
and suitable straps.
A WARNING
-Heavy loads wi ll influence the way your ve-
h icle ha ndles. To help reduce the risk of a
loss of control leading to serious personal
i njury:
-Always keep in mind when transporting
heavy objects, that a change in the cen­
ter of gravity can also cause changes in
veh icle handling:
- Always distribute the load as evenly as
poss ible.
- Place heavy objects as far forward in
the luggage compartment as possible.
- Never exceed the Gross Axle We ight Rat­
ing or the Gross Vehicle Weight Rating
specif ied on the safety compliance stick­
er on the left door jamb. Exceed ing per­
miss ible weight standards can cause the
veh icle to slide and handle differen tly.
- Please observe information on safe dr iv­
ing
¢page 160.
A WARNING
-
To help prevent poisonous exhaust gas
from being drawn into the vehicle, a lways
keep the rear lid closed while driving.
- Never transport objects larger than those fitting comp letely into the luggage
area because the rear lid cannot be ful ly
closed.
- If you absolutely m ust dr ive wi th the rear
lid open, observe the following notes to
red uce the risk of poisoning:
- Close all windows,
- Close the Panoramic sliding sunroof *,
- Open all air outlets in the instrument pane l,
- Switc h off the air recirculat ion,
- Set the fresh air fan to the highest
speed.
A WARNING
Always make sure that the doors, all win­
dows, the Panoramic sliding sunroof * and
the rear lid are securely closed and locked
-

Improperly worn safety belts
Incorrectly positioned safety belts can cause
severe injuries .
Wearing safety belts improperly can cause se­
rious injury or death. Safety belts can only
work when they are correctly positioned on the body . Improper seating positions reduce
the effectiveness of safety belts and will even increase the risk of injury and death by mov­
ing the safety belt to critical areas of the
body . Improper seating positions also in­
crease the risk of serious injury and death
when an airbag deploys and strikes an occu­
pant who is not in the correct seating posi­
tion . A driver is responsible for the safety of
all vehicle occupants and especially for chil­
dren . Therefore:
... Never permit anyone to assume an incorrect
sitting position in the vehicle while traveling
¢ ,& .
A WARNING
Improperly worn safety belts increase the
risk of serious personal injury and death
whenever a vehicle is being used.
- Always make sure that all vehicle occu­
pants are correctly restrained and stay in
a correct seating posit ion whenever the
vehicle is be ing used.
- Always read and heed all WARNINGS and
other important information
c:>page 173.
Safety belt preten­
sioners
How safety belt pretensioners work
In front, side and rear -end collisions above a
particular severity and in a rollover, safety
belts are tensioned automatically.
The safety belts are equipped with safety belt
pretensioners . The system is activated by sen­
sors in front, side and rear-end collisions of
great severity and in a rollover. This tightens
the belt and takes up be lt sla ck
c:> .& in Service
Safety belts 177
and disposal of safety belt pretensioner on
page 178.
Taking up the slack helps to reduce
forward occupant movement dur ing a colli­
sion.
@ Note
Never let the belt remain over a rear seat­
back that has been fo lded forward.
(D Tips
The safety belt pretensioner can only be
activated once.
- In minor frontal and side collisions, in
rear-end collisions and in accidents in­
volving very little impact force, the safe­
ty belt pretensioner are not activated.
- When the safety belt pretensioners are
activated, a fine dust is re leased. This is
normal and is not caused by a fire in the
vehicle.
- The re levant safety requirements must
be observed when the vehicle or compo­
nents of the system are scrapped. An au­
thorized Audi dealer or qualified work­
shop is familiar w ith these regulations
and w ill be pleased to pass on the infor­
mation to you.
- Be sure to observe all safety, environ­
menta l and other regulations if the veh i­
cle or ind ividual parts of the system, par­
ticularly the safety belt or airbag, are to
be disposed. We recommend you have
your authorized Audi dealer perform this
service for you.
Service and disposal of safety belt
pretensioner
The safety belt pretens ioners are parts of the
safety belts on your Audi. Insta lling, remov­
ing, servic ing or repair ing of belt pretension­
ers can damage the safety belt system and
prevent it from working correctly in a colli­
s ion .
T he re are some important things you have to
know to make sure that the effectiveness of .,. •
•

178 Safety belts
the system will not be impaired and that dis­
carded components do not cause injury or pollute the environment .
.&_ WARNING
Improper care, servicing and repair proce­
dures can increase the risk of personal in­
jury and death by preventing a safety belt
pretensioner from activating when needed
or activating it unexpectedly:
- The belt pretensioner system can be acti­
vated only once . If belt pretensioners
have been activated, the system must be
replaced.
- Never repair, adjust, or change any parts
of the safety belt system.
- Safety belt systems including safety belt
pretensioners cannot be repaired. Spe­
cial procedures are required for removal,
installation and disposal of this system.
- For any work on the safety belt system,
we strongly recommend that you see
your authorized Audi dealer or qualified
technician who has an Audi approved re­
pair manual, training and special equip­
ment necessary.
@) For the sake of the environment
Undeployed airbag modules and preten­
sioners might be classified as Perchlorate
Material -special handling may apply, see
www.dtsc.ca.gov/haza rdouswaste/per­
chlorate. When the vehicle or parts of the restraint system including airbag modules
safety belts with pretensioners are scrap­
ped, all applicable laws and regulations
must be observed . Your authorized Audi
dealer is familiar with these requirements
and we recommend that you have your
dealer perform this service for you.

194 Airbag system
-If the vehicle or the circuit interrupter
is scrapped, all applicable safety pre­
cautions must be followed.
@, For the sake of the envi ronment
Undeployed airbag modu les and preten­
sioners might be classified as Perchlorate
Material -special handling may app ly, see
www.dtsc.ca.gov/hazardouswaste/per­ chlorate. When the vehicle or parts of the
restraint system including airbag modules
and safety belts w ith p retens ioners are
scrapped, all applicable laws and regula­
tions must be observed. Your authori zed
Aud i dea ler is familiar wit h these requ ire­
ments and we recommend that you have
your dealer perfo rm this service for you.
Other things that can affect Advanced
Airbag performance
Changing the vehicle's suspension system can
change the way that the Advanced Airbag Sys­
tem pe rforms in a crash. For example, using
tire-r im combinations not app roved by Aud i,
lowe ring the vehicle, ch anging the stiffness of
the suspension, incl uding the springs, s uspen­
sion struts, shock absorbers etc. can change
the forces that are measured by the ai rbag
sensors and sent to the electronic control
un it. Some suspension changes can, for exam­
p le, increase the force levels measured by t he
sensors and make the airbag system deploy in
crashes in wh ich it would not dep loy if the
cha nges had not been made. Other k inds of
cha nges may reduce the force levels meas­
ure d by the sensors and preven t the a irbag
from deploying when it sho uld .
The senso rs in the safety belt buckle fo r th e
d river and front passe nger sea t tell the elec­
tronic control module if the safety belt is
l atched or not. I f the safety belt is being used,
the front airbag will deploy at a slightly high­ er rate of vehicle deceleration than if the safe­
ty belt is not being used. Therefore, in a par­
ticular collision, it is poss ible that an airbag
will not deploy at a seating position where the safety belt is being used but will inflate at the position where t
he safety be lt is not being
used. It is important that nothing interfere
with the safety be lt b uckles so that the sen­
sors can send the correct information about
safety belt use to the electronic control un it.
A WARNING
=
Changi ng the veh icle's suspension includ-
i ng use of unapp roved tire-rim combina­
tions can change Advanced Airbag per­
fo rma nce and increase the r is k of seri ous
personal injury in a cra sh.
- N ever install suspension components
that do no t have the same pe rformance
chara cter istics as the compone nts o rigi­
na lly ins talled on your vehicle .
- Never use tire-rim combinations that
have not been approved by Audi.
A WARNING
= -
It ems stored between the safety be lt
bu ckle and the cente r console can cause
the sensors in the b uckle to send the
wrong information to the e lectronic con­
trol module and prevent the Advanced Air­ bag System from working prope rly.
- Always make sure that nothing can inter­
fere with the safety belt buckles and that they are not obstructed .
Side airbags
Description of side airbags
The airbag system can provide suppl emental
protection to properly restrained occupants.
F ig . 20 0 Side air bag locat ion in th e driver's seat

226 Intelligent technology
can result in there being insufficient energy
avai lab le to start the engine .
I ntell igent energy management in your vehi­
cle handles the distribution of electrical ener­
gy . Starting abi lity is markedly improved and
the life of the battery is extended .
Basically , energy management consists of
battery diagnosis , idling current manage­
ment
and dynamic energy management.
Battery diagnosis
Battery diagnosis continuously determines
the state of the battery. Sensors determine
battery volta ge, battery current and battery
temperature. This determines the current
state of charge and the power of the battery.
Idling current management
Idling current management reduces energy
consumption while the vehicle is stand ing.
With the ignition switched off, it contro ls the
energy supply to the various e lectrica l compo­
nents. Data from battery diagnosis is consid­
ered.
Depending on the battery's state of charge,
individua l consumers are gradually turned off
to prevent excessive discharge of the battery
and thus maintain starting capability.
Dynamic energy management
While the vehicle is being dr iven , dynamic en­
e rg y management distributes the energy gen­
erated according to the needs of the individu­
a l components. It regulates consumption, so
that more ele ctrical energy is not being used
than is being generated and ensures an opti­ mal state of cha rge for the battery.
{D) Tips
- But even energy management cannot
negate the limits of physics. Consider
that the power and life of a battery are
limited .
- If starting ab ility is threatened, you are
i nformed by a warn ing
c> page 22 7,
Driver notification in the instrument
cluster display .
What you should know
The highest priority is given to maintaining
starting capability .
The battery is seve rely taxed in shor t-distance
driving, in city tra ffic and dur ing the cold time
of year . Abundant electrical energy is re ­
quired, but only a little is generated . It is also
critical if the engine is not running and e lectri­
ca l components are turned on . In this in­
stance energy is being consumed but none is
being generated.
It i s in precisely these situations that you will
notice energy management actively regulat­
ing the distribution of energy.
Vehicle stands for an extended period
If you do not drive your vehicle over a period
of several days or weeks , e lectr ica l compo­
nents are gradually cut back or sw itched off.
T his reduces energy consumption and main­
ta ins start ing capability over a longer period .
Take into consideration that when you unlock
your vehicle , some conven ience functions ,
s uc h as the inte rior lights or the power seat
adjustment, may not be available. The con­
venience functions will be available again
when you turn on the ignition and start the e ngine .
With the engine turned off
If you listen to the radio, for example, w ith
the engine turned off or use other MMI func ­
tions, the battery is being discharged .
If starting capability is jeopardized due to en­
ergy consumption , the following warning ap­
pears in the MMI display:
Please start engine, otherwise system will
switch off in 3 minutes .
The warning indicates that the system will be
turned off automatically after 3 minutes . If
you w ish to continue using the funct ions, you
have to sta rt the eng ine.
1111>

on a slope w ithout the veh icle tipping over
sideways (depends on center of gravity). Maxi­ m um permitted latera l ang le: 35°
Breakover angle
I ndicates the angle up to whi ch the veh icle
can drive ove r a ramp at low speed w it h out
the unde rside of the vehicle hitting the edge
of the ramp.
- Vehicl es with out air spring s: maximum
breakover ang le: 21, 1 °
- Vehicles with adaptive air su spen sion* :
maximum b reakove r angle: 23.8° (at h igh
l evel 2)
Approach /d eparture angle
Transition from the horizontal p lane to a gra­
d ient or from a grade bac k to level ground . In ­
d ic a tes the angle up to which the vehicle can
drive onto or off a slope at low speed wi thout
striking the bumper or the underbody.
- Vehicl es without air spring s: maximum ap­
proach/depart ure angle: 21.0° (front),
23.4 ° (rear)
- Vehicl es with adaptiv e air su sp ension* :
maximum approach/departu re angle at high
l evel 2 : (front) 23,5°, (rear) 25 .4°
Ground clearance
The distance between the road surface and
the lowest po int of the ve hicle underbody .
-Vehicles w ithout air spring s: ground clear­
ance: 8 .1 in (204.8 mm)
- Vehicles w ith adapti ve air suspension *:
maximum ground clearance: 9 .4 i n
(239 .8 mm) at high level 2
A WARNING
Exceeding the stated maximum figures
can result in severe injuries or ve hicle dam­
age.
- All the information was gathered on lev­
el, firm and non-slippery road surfaces,
and unde r dry wea ther conditions.
- Ideal conditions do not p revail offroad.
Never utilize the maximum read ings to
Driving off road 233
their f ullest, always leave a safety re­
serve.
Driving tips
On poor road and offroad, there is always on ­
ly one motto: Plan ahead and drive slowly!
Please obse rve the fo ll ow ing when d riving
away from paved roads :
.,. Drive on ly on roads and offroad sections
which ma tch the design of yo ur vehicle and
your abilities as a driver. Never take r is ks!
.,. Drive slow ly and plan ahead!
.,. Take into consideration the
ground clear­
an ce
of your vehicle .
.,. Act ivate the
ESC off road mode q page 219
as needed.
.,. Use the
hill descent control q page 220
when dr iv ing down steep sections on h ills .
Unpa ved ro ads and offroad
Drive slowly on unfamiliar roads and unknown
offroad section s, and look out for unexpected
obstacles (e .g. po tholes, rocks, tree s tumps,
etc .) .
To prevent the vehicle from bottoming and
avo id damage to the underbody, you should
drive straight across severe bumps in the
ground with only one side of the veh icle so
that only two of your whee ls cross the bumps .
Drive b risk ly through sandy or marshy offroad
sec tions and do not stop, i f at all possible .
Driving throu gh wate r
Note the following to avoid vehicle damage
when d riving through water, for examp le on
flooded roads:
- The wa ter must not be any higher than the
bottom of the vehicle body .
- Do not dr ive faste r tha n walk ing speed .
Driving on a slope
If you ever find yourself not able to climb a
s lope, do not try to turn around , drive back
down in
r e ver se . Otherwise, you run the r isk
of tipp ing ove r. ..,.
•
•

236 Trailer to wing
-The Gross Vehicle Weight Rating for yo ur
Audi Q7 would be exceeded if your vehi­
cle is simultaneously equ ipped w ith Pan­
oramic sl iding sunroof; th ird-row seat­
ing; trailer towing equipment (factory or
dealer-installed), and running boards
(dea le r-installed) . UNDER NO C IRCUM­
STANC ES MAY AL L SUC H ITE MS BE IN­
STALLED ON THE SAM E VEH ICLE.
Operating instructions
MAX 6 .9 "
MAX175mm
E
"' E
"' .... a)
rt
Fig. 219 Permi tted ball p osit ion of the t ra iler hitc h
Traile r to wing we ight s
W it h a fac tor y-ins talled trailer hitch, the
maximum permissible trailer we ight is 6 ,615
lbs (3,000 kg) . The maximum permissible un­
braked trailer weight is 1,650 lbs (750 kg) .
W ith an aft er mar ket trailer hitch, the maxi­
m um permissible trailer we ight is 5,512 lbs
(2,500 kg) . These specifica tions apply when
driving on roads having an incline of less than
12%.
Perm issible tongue load
F or best vehicle handli ng u nder these
changed condit ions, adjust the trailer load so
that the tongue load is at the maxim um al ­
l owable or slightly lower. Yo u can get an ap­
proximation of the tongu e load with a bath­
room scale o r you c an measu re the load at a
trucking company or weighing s ta tion.
With a factory-in stalled trailer hitch, the
maximum permissib le load on the ball hitch
may not exceed 662 lbs (300 kg). With an af­
termarket trailer hi tch, the maximum permis­
sib le load on the ball h itch may not exceed 551
lbs (250 kg) . It is recommended to use
the maximum permissible load.
Trailer load distribution
Be sure the load in the t ra iler is held secure ly
in place to prevent it from shift ing forward,
backward or sideways.
Nev er allow a pas seng er t o rid e in a trai ler
¢&. in Driving instructions on page 23 7.
Ball m ount
The trailer hi tch may only be used w ith suita­
ble ball mount and ball¢
fig. 219 . Installa ­
tion of the h itch ball must be carried out in ac­
cordance with the manufacturer's inst ruc­
tions . At the height dimens ion of 1.5 in
(38 .5 mm) a tolerance of+/- 0.5 in ( 12. 7 mm)
is permissible .
Engine cooling system
Towing a trailer makes the engine work hard­ er . It is impo rtant that the cooling system's
performance is up to the additional load.
Make sure that the cooling system has enough
fluid.
T ire pressur e
When towing a trailer, inflate the tires of your
vehicle to the cold ti re pressu re listed under
" F u ll load" on the tire pressure label. The tire
pressure label is located on the drive r's side B­
pillar . Inflate trailer tires to t railer and tire
manufacturers' specifications.
Lights
T he headlight settings should be checked wi th
t h e trai ler attached before d riving
off. Check
to make s ure both vehicle and trailer lights
are worki ng properly.
Safety chains
Be sure trailer safety chains are properly con­
nected from the trai le r to the hitch on the ve­
hicle. Leave enough slack in the ch ains to pe r­
mit turning corners. When you install safety
chains, make sure they will not drag on the
road when you are driving. ..,.