12 Instrum ents a nd warning /indic ato r li ghts
coolant temperature is too high, or the cool
ant
level is too low ¢ page 17.
.&_ WARNING
- Always observe the warning in
¢ page 187, Engine compartment be
fore opening the engine hood and check
ing the engine coo lant level.
- Never open the engine hood if you see or
hear steam, or if you see engine coolant
dr ipping from the eng ine compartment.
You could burn yourself . Let the engine
cool off first so that you cannot hear or
see any steam or engine coolant .
0 Note
-Mounting additional l ights or accesso ries
i n front of the a ir inlets reduces the cool
i ng effect of the rad iator. At h igh outside
temperatures or high eng ine load, the
engine could overheat.
- The front spo ile r has been designed to
properly distrib ute the cooling air when
the veh icle is moving.
If the spoiler is
damaged, this cou ld reduce the cooling
effect and the engine could then over
heat. Ask your authorized Audi dea ler for
assistance.
Fuel gauge
The fuel gauge works only when the ignition is
on.
When the needle reaches the red area, the
warning light in the instrument cluster will il
lum inate <=>
page 21 lil This means you
have approximately
1.8 gallons (7 liters) of
fuel left in the tank .
Time to re fu el!
The total tank capacity of your vehicle is listed
in¢
page 257, Data.
(D Note
Never run the tank completely dry! An ir
regular supply of fuel can cause eng ine
m isfiring and fuel could enter into the ex
haust system. The catalyt ic converte r
could then overheat and be damaged.
Speedometer with odometer
The speedometer shows you the vehicle
speed, and the odometer shows you how
many miles (kilometers) you have driven.
F ig . S Speedometer close- up: odom eter display
The odometer and trip odometer are located
inside the speedometer .
- USA models -Miles
- Canadian models -Kilometers
Lower odometer
The lower odometer shows the total number
of miles (kilometers) driven.
Uppe r odometer (trip odome ter)
The upper odometer shows the total number
of miles (kilometers) driven since you last re
set the odometer back to zero. You can use
th is odometer when you want to keep track of
how many miles (kilometers) you have driven
for a single tr ip or errand. The last digit ind i
cates 1/10 of a mile (100 metres) . You can set
the tr ip odomete r back to zero by pressing the
rese t button
c:> fig. 5.
Malfunct ion me ssage
If there is a malfunct ion somewhere in the in
strument cluster,
dEF w ill appear in the trip
odometer and w ill stay on . Contact your au
thorized Audi dea ler to have the problem cor
rected.
Immobilizer
When the ignition is sw itched on, the data on
the ignit ion key are scanned automat ically .
If an unauthorized key was used,
SAFE is dis
played continuously in the odometer d isplay
II>
14 Instrum ent s and w arn ing /indic ato r light s
Engine coolant level too low
ii
Engine oil sensor malfunction
engine coolant temperature too
¢page20
high ¢page 17
•
Battery voltage too h igh or too low
Electro-mechanical power assist
¢page20
¢page 17
II
Low fuel level
Clutch is overheating
¢page 21
¢page 101
•
Windshield washe r fl uid level low
Y ellow indicator lights ¢page 21
D
Yellow symbols indicate a priority 2 ma lf u nc-
~:~
Defective light bulb
tion -Warning!
¢page 21
Ji]
Electronic Stab ilizat ion Program
•
U SA mod els : Defective brake light
(ESP)
./¢page 18
¢page 21
I
Electronic Stabilization Program
•
Canada model s: Defective brake
(ESP)./
<=:>page 18 light ¢ page 21
~ USA mod els : anti-lock brake system
II
Dynamic headlight range cont ro l*
(ABS) ./ defective
<=:> page 18 defective ¢ page 21
Canada models: anti-lock brake sys--
[I]
•
Adaptive Light * defective
tern ./ (ABS) defective
¢page 18
¢page 21
•
Worn brake pads
m
Light/rain sensor defective (automat-
¢ page 19 ic headlights) * defective ¢ page 22
g
Tire pressure too low
B
Audi magnetic ride
¢page 19
¢page22
ll@I@ Tire pressure monitoring system
~
USA models: Speed warning 1
¢page 231
¢page 31
[m
Electronic power control./
¢page 19
•
Canada models : Speed warning 1
¢page 31
•
USA models: Malfunction Indicator
Lamp (MIL)
¢page 19
•
USA models: Speed warn ing 2
¢page31
Canada models: Malfunction Indica-
tor Lamp (MIL)
¢page 19
•
Canada models: Speed warning 2
¢page 31
II
Glow plug system ./ (diesel engine
Electro-mechanical power assist
only) (alternative to~ )
M ¢page 17
¢page20
.,
Engine speed limitation *
Diesel particulate filter
¢page20
¢page22
Ill
Check engine oil level
¢page20
16 Instrum ent s and w arn ing /indic ato r light s
immediately by your authorized Audi
dealer or a qualified workshop. Drive
slowly and avoid sudden, hard brake ap plication.
- Canada models: If both, the brake warn
ing light . and the ABS warning light
Ii] come on at the same time, the rear
wheels could lock up first under hard braking. Lock-up of the rear wheel brakes
can cause loss of vehicle control and an
acc ident. Have your vehicle repaired im
med iately by your authorized Audi dealer
or a qualified workshop. Drive slowly and avoid sudden, hard brake application
- If the brake warning/indicator light does not go out after a few seconds and the
park ing brake re leased, or lights up while
you are driving, the fluid level in the brake flu id reservo ir is too low. If you be
lieve that it is safe to do so, proceed im
med iately at low speed to the nearest
authorized Audi dealer or qualified work
shop and have the bra ke system inspect
ed.
- Always keep in m ind that afte r several
brake applicat ions, you will need g reater
pressure on the b rake peda l to stop your
vehicle. Do not re ly on strained brakes to
respond with maxim um stopping power
in critical situations . You must allow for
increased brak ing distances. The extra
distance used up by fad ing brakes could
lead to an acc ident.
~ / ! .!r Safety systems
The I (USA models)/ . (Canada mode ls) in
d icator light monitors the safety systems e.g.
a irbags, pretensioners a nd illum inates for a
few seconds each time you switc h the ign ition
on.
If the
I (USA models)/ . (Canada models)
indicator light does not go out, or if it illumi
nates w hile you are driv ing, or if it sta rts to
b lin k, then there is a ma lf u nction somewhere
in the system. If the light does not illuminate
when you switch on the ignition, this also
means there is a ma lfunction.
A WARNING
If you have a ma lfunction in the safety sys
tems, contact your authorized Audi dea ler
i mmediately. Otherwise the safety sys
tems may not work properly in an acc i
dent.
~ Safety belt warning light
App lies to veh icles : w ith safe ty belt warni ng lig h t
The warning light is a reminder to fasten
safety belts .
The warning lig ht . comes on for a few sec
onds after the ignition is sw itched on as a re
minder to fasten your safety belt .
Additional information on safety belts
r::> page 113.
D Generator '
This warning/indicator light detects a mal
function in the generator or in the vehicle 's
electrical system.
The . warning/indicator light i llum inates
when you switch on the ignition and must go
out after the eng ine has started.
If the . warning/indicator light illuminates
whi le you are driving, you sho uld contact your
authorized Aud i dea ler. Since the vehicle bat
tery is discharging, you shou ld sw itch
off any
unnecessary electr ica l consumers (for exam
ple, the air conditioner) .
~ Engine oil pressure
The red engine oil pressure warning symbol
requires immediate service or repair .
If the . symbo l appears in the d isplay and
flashes, the o il pressure is too low . In add ition
to the symbol, the following message a lso ap
pears in the display:
Switch off engine! Oil pre ssure is too low
.. Pull off the road and stop the vehicle.
.. Shut the engine down.
.. Check the engine oil leve l¢
page 200.
Instruments and warning/indicator lights 17
~ Cont act your a uth orized Audi dea ler fo r as -
s istance if necessary.
Engine oil level too low
If t h e e ngine o il level is too low, to p off o il to
the prope r leve l¢
p age 200.
Engine oil level OK
If the . symbol sta rts flas hing again even
though the engine oil level checks OK on the
d ipst ick ,
do not start driving again and do
not let the engine run at idle .
In stea d, con
t a ct your author ized A udi de aler for assis
tance.
@ Tips
- The engine oil pressure symbol. is
not an indicator for a low engine oil lev
el. Do not rely on it. Instead, check the
oil level in your engine at regular inter
vals , preferably each time you refuel,
and always before going on a long trip.
- The yellow oil level warning indication
1/1 requires oil refill or workshop serv
ice without delay. Do not wait until the
red oil pressure warning symbol.
starts to flash before you respond to
the low oil level warning
Ill. By then,
your engine may already have suffered
serious damage.
- L Engine cooling system
A malfunction in th e engine cooling system
must b e re paired as so on as possibl e.
W hen th e . symbol in t he d isp lay flashes,
the n either the eng in e coolan t
temperature is
too h igh, or the coo lant
le vel is too low . In ad
d ition to the symbol, the following message
al so a ppe ars i n the dis pla y:
Switch off engin e and check coolant level
~ Pull off the road and stop the vehicle.
~ Turn off t he e ngine.
~ Check coo lant level c> page 204.
~ Add coolant if necessa ry¢ page 204 .
~ Continue dr iving only after the eng ine cool
an t war ning/ indica to r li ght goes o ut.
~ Contact yo ur autho rized A udi d eale r for as -
sistance if necessa ry .
If the engi ne coo lant level is correct, then t he
r adi ator fan may be the ca use of the mal func
tion .
If the ge nera tor war ning/ indica to r li ght
sho uld al so illum ina te
¢ page 16, then the
f an belt may be d amaged .
A WARNING
-If you r vehicle should brea k dow n for
mec hanical or other reaso ns, par k at a
safe distance fr om moving traffic, tu rn
off the eng ine and tu rn on the haza rd
warn ing lig hts ¢
page SO , Emergency
flash er.
-
- Never ope n the hood if you see or hear
steam or coo la nt escaping from the en
g in e com part men t - yo u ris k bei ng scald
ed . W ait unt il yo u can no lo nger see o r
hea r stea m or cool ant escap ing.
- The engin e compa rtm en t of any vehicle
is a dange rous area. Befo re you perfor m
a ny w ork in t he engi ne c om pa rt men t,
t ur n off t he e ngine a nd allo w it to c ool.
F ollow t he warn ing s tickers
c> page 18 7,
Engine comportment.
([) Note
Do not con tinue dr iv in g if the . sym bol
ill umin ates . The re is a ma lfun ctio n in t he
engine coo ling system -yo u could dama ge
your engine .
~ Electro-mechanical power assist
If the indicato r light illum inates while yo u are
driv ing, the re is a malfunction in the electro
mecha nica l steer ing. If t he indicator light is
showing
t~J, there may be a reduct io n in pow
er stee rin g assis t. If the indicato r light is
s h owing ., th ere may be a tota l loss of pow
er stee rin g assis t. T he s teer ing mu st be i n
s p ecte d imme diately by a qualifie d wo rks hop
¢ .& .W ith the eng ine not ru nning (e. g. when
the car is bein g towe d), there is a lso no power
ass ist available . ..,.
20 Instruments and warning /indicator lights
The symbol lll lights up when the ignition is
turned on and will turn off after the engine
has started and has sett led at constant idle
speed. This indicates that the MIL is working
properly.
The warning light illuminates when there is a
malfunction in the engine e lectronic system .
Contact your authori zed Audi dealer and have
the malfunction corrected .
An improperly closed fuel filler cap may also
cause the MIL light to illuminate
¢page 192.
F or more information ¢ page 24.
W Glow plug system I Engine
malfunction
Applies to vehicles: with diesel eng ine
The indicator lamp lights up to show that the
glow plugs ore preheating. It flashes if there is an engine malfunction.
Warning light II stays lit up
If the II indicator light illuminates, the g low
p lug system is active. You shou ld start the en
gine immediately after the indicator light
switches off. The indicator light on ly illumi
nates for approximately 1 second if the en
gine is warm or if the outside temperature is
above 46 QF (8 QC) .
There is a fau lt in the glow plug system if the
warning light
II does not light up when the
engine is
cold . Contact an author ized Audi
dealer or a qualified workshop .
II Warning light flashes
If a malfunction develops in the engine man
agement system while you are driving, the
glow plug light will flash
II . The eng ine
should be checked by an authorized Audi deal
er or a qualif ied workshop as soon as possible .
A WARNING
If you do not pay attention to the warning
lights that have come on, this could lead
to personal injury or damage to your vehi
cle.
! 7} Engine speed limitation
Applies to vehicles: with engine speed limitat ion
Ill Do not exceed max. engine speed of XXXX
rpm
The Ill symbol illuminates when there is an
engine control malfunct ion. The ind icator
light~ in the instrument cluster also illumi
nates. The engine speed is limited to the
speed displayed in the driver information sys
tem. Keep in mind that the engine speed wi ll
not exceed the val ue displayed in the driver in
formation system, for example when down
shifting.
Please go to an authorized Audi dealer or oth
er qualified workshop to have the malfunction
repaired.
~ .. Checking the engine oil level
When the II symbol illum inates, check the
engine oil level as soon as possible
¢ page 200 . Top off the oil at your earliest
opportunity ¢page 200.
II Please add max. 1 qt of engine oil!
If the II symbol comes on, add 1 quart (1 li
ter) of oil at the next opportunity
¢ page 200.
• ~m Engine oil sensor defective
If the Ill symbol illuminates, contact your
authorized Aud i dealer and have the oil sensor
inspected .
0 Battery voltage low
(•i Low battery charge: battery will be
charged while driving
If the indicator light turns on and the mes
sage appears, there may be limited starting
ability.
If this message turns off after a little while,
the battery charged enough while driving .
164 Intelligent technolog y
Faults in the bra ke sys tem
If you should notice a sudden increase in
b rake peda l travel, then one of the two brake
circuits may have failed¢.& .
Low brake flu id le vel
Malfunct ions can occur in the brake system if
the brake fluid level is too low . T he brake fluid
l eve l is moni to red electronica lly .
Bra ke lining w ear st atu s
Brake l ining wear may be checked by visual in
spection of the condition of the brake pads
through the openings in the whee l. If neces
sa ry, the wheel may be removed for this in
spection
¢page 236, Wheel change.
A WARNING
-You should perform braking maneuvers
for the purpose of cleaning the brake
system on ly if road conditions permit.
Other road users must not be put at risk -
you may cause an acc ident!
- Before descending a steep grade, reduce
speed and shift transmiss ion into a lower
gear or lower driving range . Do not ride
the brakes or hold the pedal down too long or too often. This cou ld cause the
brakes to get hot and dimin ish braking
efficiency.
- Do not "r ide the brakes" by resting your
foot on the pedal when yo u do not intend
to bra ke . This may cause the brakes to
overheat, premature wear and increased
stopping distance .
- Under certain climat ic and operating
condit ions such as passing through wa
ter, driving in heavy rain or after washing
the vehicle, the effectiveness of the brakes can be reduced. In winter, ice can
accumulate on the brake pads, linings,
discs and drums . Carefully apply brakes
for a test . Brakes will dry and ice coat
ings will be cleaned off after a few care
ful brake applications.
- Driv ing for an extended period of time on
salt-covered roads w ithout us ing your
brakes can also affect braking efficiency . Clean off accumulated salt coating from
brake discs and pads with a few careful
brake applications.
- If you damage the front spoiler, or if you
install a different spoiler, be sure the a ir
flow to the front brakes is not obstruct ed. Otherwise the brake system could
overheat reducing the effectiveness of
the entire brake system.
- Failure of one brake circuit will impa ir
the braking capab ility result ing in an in
creased stopping distance. Avoid driving
the vehicle and have it towed to the near
est a utho rized Audi dea le r or q ualified
wo rkshop.
Brake booster '
The brake booster adds extra broking power.
The brake booster works with vacuum pres
sure which is created only when the eng ine is
run ning ¢.&_ .
_&. WARNING
-Never let the vehicle roll to a stop with
the engine shut off.
- I f the b rake booster is not working, for
examp le when towing yo ur vehicle, or
because the brake booster has somehow
been damaged, the brake pedal must be
pressed conside rably harder to make up
for the lack of booster assistance.
Functioning of Anti-Lock Brake System
(ABS)
ABS prevents the wheels from locking up un der broking.
.
The ABS contributes effectively to vehicle con
trol since it prevents the whee ls from
locking
when the brakes are applied. This means that
the vehicle remains steerable and is less likely
to sk id .
With ABS you do not need to pump th e
brake. Ju st hold the b ra ke pedal down.
170 Driving and en vironm ent
Driving through water on roads
Note the following to avoid vehicle damage
when dr iv ing t hrough water, for example on
flooded roads:
- The water must not be any higher than the
bottom of the vehicle body.
- Do not drive faster than walking speed.
A WARNING
After d riving through wate r, mud, slush,
etc., the brakes may be slow to take effect
because o f wet brake ro tors and pads. Dry
the brakes f irst by bra king carefully to re
store the full braking effect .
({D Note
Vehicle components such as the engine,
t ransmiss ion, suspens ion or elect rical sys
tem can be severely damaged by driving
through wate r.
(D Tips
-Che ck the depth of the water before dr iv
i ng through it.
- Do no t stop the veh icle, dr ive in reverse
or switch the engine off when d riving
th rough water.
- Keep in mind that oncoming vehicles
may c reate waves that raise the wate r
l evel and make it too deep for yo ur vehi
cle to drive th rough safely .
- Avoid driving thro ugh salt water because
i t can ca use corrosion.
Catalytic converter
-
It is very important that your emission con
trol system (catalytic converter) is function
ing properly to ensure that your vehicle is run
ning in an environmentally sound manner .
"' Always use lead-free gasoline¢ page 189,
Fuel supply.
"' Never run the tank down a ll the way to
empty .
"' Never put too much motor oil in your en
gine ¢
page 200, ~ Adding engine oil .
"' Never try to push -or tow-start you r vehicle .
T he ca talytic converter is an efficient "clean
u p" dev ice bui lt into the exhaust system of
the vehicle . The cata lytic conve rter bu rns
many of the pollutants in the ex ha u st gas be
fore they are re leased into the atmosphere.
T he exclusive use of unleaded f uel is c rit ically
important for the life o f the catalyt ic convert
er and prope r function ing of the engine .
A WARNING
-Do not park or operate the vehicle in
areas where the hot exhaust system may
come in contact with dry grass, brush,
fue l spill or other material wh ich can
cause a fire .
- Do not app ly additional undercoating or
rustp roofing on or near the exhaust
manifold, exhaust pipes, catalytic con
verter or heat shields. Dur ing driv ing, the
substance used fo r under coating could
overhe at and cause a fire.
((0 Note
-Be aware that just one tank filling with
leaded fuel w ill alr eady ser iously de
grade the performance of the catalytic
converte r.
- Do not exceed t he cor rect engine oil level
¢page 200.
-Do not dr ive until t he fuel tank becomes
completely empty. The engine cou ld mis
fire. Unburned fuel could also get in to
the exhaust system and th is co uld cause
t he catalytic converter to overheat .
- Do not tu rn off the igni tion while the ve
hicle is mov ing.
- Do not continue to ope rate your veh icle
under these conditions, as ot herwise fuel
can reach the catalytic converter. This
cou ld resu lt in overheating of the con
verter, requir ing its replacement.
- To assu re efficient operation of the Emis -
sion Control System : ..,.
198 Checking and filling
Mo dern engine lubrication has taken a quan
tum leap in the last few years. Many synthetic
oils ava ilable today provide better engine lu
brication that can outlast traditional petrole
um-based o ils, making them a smart choice
for use throughout the life of your Audi .
Whether you use synthetic or petroleum
based engine oil, the oil that yo u use must
conform to Audi 's oil quality standard
VW 502 00 (veh icles with gasoline engine)
and VW 507 00 (vehicle with diesel engine) to he lp keep your vehicle's eng ine runn ing
smoothly and help prevent the fo rmation of
harmf ul depos its , somet imes ca lled "sludge,"
that over t ime can lead to expensive repairs.
At the time of printing , engine oils availab le in
the U .S . and Canada that meet the exa cting
specifi cations o f A ud i oi l st andard VW 502 00
(vehicles wi th gaso line engine) and
VW 507 00 (vehicles with diese l engine) are
synthetic engine oils . This does not mean,
however, that every synthetic engine oil wi ll
meet Audi oil standard VW 502 00 (gasoline
engines) and VW 507 00 (d iesel engines). So
a lway s be sure that you use a n approved o il.
To help prevent the fo rmation of harmful de
posits use only oil w ith the following specifi
c ations printed on the oil conta iner:
- Ga soline engines: Audi oil standard
VWS0200
- Die sel engines: Audi oil standard
vw 50 7 00
Oil container labe ls may carry t he specifica
tion s ingly or in comb inat ion with other des ig
nations and oil qua lity standards.
Vi scosity
Eng ine oi ls are graded according to their v is
cosity . The proper v iscosity grade o il for your
engine depends on cl imactic or seasonal con
d itions w here you dr ive. Yo u can use oi l w ith a
viscosit y grade of SAE 5W-40 a cross all tem
perat ure ranges for normal d riving conditions .
H owever, if eng ine o il viscos ity grade SAE
5W-40 is not ava ilable, you can a lso use vis
cosity g rade SA E 5W-30 or SAE OW-40 as long as it meets A
udi o il quality standard
VW 502 00 (vehicles wit h gasoline engine) or
VW 50 7 00 (vehicles wit h diese l eng ine) spec
ifications.
Beca use engine o il that meets the Audi oil
sta ndard may not be availab le everywhere
when you need it, we strong ly recommend
that you a lways carry with you an extra qua rt
( li ter) of oil that express ly conforms to the
VW 502 00 (vehicles wit h gasoline eng ine) o r
VW 507 00 (vehicles w it h diesel eng ine) spec
i fication, i n case you have to top off the oi l
wh ile on the road.
App lies to vehicle s with gasoline engin e on
ly:
Only if the level of the o il is at or below the
min imum ma rk - and no o il that expressly
c onfo rms to Audi oil standa rd VW 50 2 00
specifica tions is available - may you top off
with a high quality engine o il , pre fera bly syn
t h etic-based, that meets ACEA A3 or API SM
specifications, but even then, only in viscosity
grades SAE 5W-40, SA E 5W-30, or SA E
OW-40. However, dur ing the entire time be
tween oil change interva ls, never top off with
more than a total of 0.5 qt/liter engine o il
that does not confo rm to Aud i oil spec ification
vw 502 00 .
Applies to vehicles with diesel engine only:
Only if the level of the oil is at or be low the
min imum ma rk - and no o il tha t expressly
confo rms to Audi oil standa rd VW 507 00
spe cifications is available - may you top off
wi th a high quali ty engine o il, that meets
AC EA C3 o r API CF specifica tions, but even
then , on ly in viscosity grades SAE 5W-40 , SAE
5W-30, or SAE OW-40 . However, during the
entire t ime between oil change intervals, nev
er top off with more than a tota l of 0.5 qt/li
ter engine oil that does no t conform to Aud i
o il specification VW 507 00 .
For more information about eng ine oi l that
has been approved for your veh icle, please
contact e ither your au thorized Aud i dealer or
Audi Custome r Re lations at 1 (800) 822 -2834
o r vis it our web site at www.audiusa .com or
www.aud icanada .ca. He re you w ill also find a
c ur rent l ist of oi ls (manufac turers, brand .,.