2012 AUDI A3 warning

-Automat ic dimming for the m irror only
operates p roperly if the lig ht striking the
i ns ide mirror is not hindered in any way.
Wiper and washer
system
{sf) Windshield wiper
The windshield wiper lever controls both the
windshield wipers and the washer system.
F ig . 57 Wiper lever: w inds hie ld w iper lever positions
The windshield wiper lever c> fig. 57 has the
following positions:
Ql Intermittent wiping (activating rain
senso r)*
.. Move the lever up to position@.
.. Move the interval set sw itch @, to change
t h e interva ls.
Low wiper speed
.. Move the lever up to position@.
High wiper speed
.,. Move the lever up to position @.
One-touch wiping
.. Move the lever to position @, when you
want to w ipe the w indshield
briefly .
Automatic wiper /w asher
.. Pu ll the lever to posit ion ® (toward the
steering wheel) and ho ld.
.. Re lease the lever . The washer stops and the
wipers keep going for about four seconds.
Turning off th e wiper s
.. Move the lever back to position @ .
Clear vi sion 55
The w indshield wipers and washe r only work
whe n the ignition is turned on . If you switch
off the ignition with the w indshie ld w iper lev ­
er st ill in the interva l wipe position and then
come back a whi le later and drive off, the rai n
senso r will reactivate itsel f after the vehicle
speed has exceeded 4 mph (6 km/h) .
The rain sensor* is only activated with the
wiper lever set to position @. When it starts
to rain, the rain sensor will automat ically acti ­
vate the intermittent w iping mode.
To reduce the sensitivity of the sensor, move
switch ® down. To increase the sensitivity,
move t he switch up. The h igher you adjust the
sens it ivity, the faster the senso r will react
when it senses mo isture on the windsh ield .
The rain sensor w iper intervals depend on the
sensit ivity sett ing as well as vehicle speed.
D uring brief s tops, wipe r mot io n will adjust in
r elat ion to the amou nt of rain on the w ind­
shield .
Automat ic w iper/was her : To eliminate water
drople ts, t he windsh ield wiper pe rforms o ne
afterw ipe ope ra tion after severa l seconds
whi le dr iv ing . You ca n sw itch this f unct ion off
by moving the leve r to posit io n ® within
10 seconds of the afterw ipe operat io n. The af­
terwipe function is reactivated the next time
the ignitio n is switch.
When the igni tio n i s tur ned on, the washe r
jets are heated*.
& WARNING ~
- Wiper blades are crucial for safe drivi ng!
On ly when they are in good condit io n are
they able to clear the windows properly
to prov ide uncompromised visib ility.
Worn o r damaged wiper blades are a
safety haza rd
c> page 57, Replacing
front wip er blades!
- The light/rain senso r* is only des igned to
assis t and suppo rt the driver.
It rema ins
e ntire ly th e drive r's respo nsib il ity to
m onitor outside weathe r cond itions and
t o manu ally a ctiv ate the wipe rs as soo n

Switching intermittent wiper acti on off
• Pull the lever all the way back to the or igi­
nal position.
A WARNING
Wiper blades are crucial for safe driving!
On ly in good condition are they able to
clear the windows properly to provide un­
restricted visibility. Worn or frayed wiper
blades are a safety hazard!
r::;, page 5 7,
Replacing front wiper blades
Q) Note
In freezing or near freez ing cond itions:
- Always check t hat the wiper blades are
not frozen to the glass before yo u turn
the wiper on. loosen a wiper blade which i s frozen in p lace before operating the
wipe r to preve nt damage to the wiper
blade o r the w ip er motor .
-
-Do not use the wiper to clear a frosted
window . Using the wipers as a conven ­
i ent ice sc raper will destroy the w iper
blades .
(D Tips
For better rea rward vision whe n pa rking,
the r ear w indow w ip e r is automat ica lly ac­
t iva ted one time when the windshield wip­
ers are sw itche d on and reve rse gear is en­
gaged.
Service position
Replacing the windshield wiper blades is only
possib le when you move the wiper arms into
the service position. In order to use the wind­
shie ld w ipers, the hood must be complete ly
closed . When there is a risk of frost, make
sure that the w iper blades are not frozen to
the windshield .
• Switc h the ignition on .
• Switch the ignition off aga in and move the
wipe r lever
r::;, page 55, fig . 57 from position
0 to 1 within 10 seconds . The w iper arms
now move in to the fie ld of v iew in t he wind­
shield .
Clear vision 5 7
The service pos ition can a lso be selected in
the d river information system*
r::;, page 27 .
(D Note
Neve r dr ive y our veh icle w hen the w ind­
shield wiper a rms are in the se rvice posi ­
tion and pulled away from the winds hield.
W hen yo u drive faster than 4 mph (6 km/
h), the wiper arms automatically return
back to the park position and could ca use
paint damage to the eng ine hood!
(D Tips
- Yo u can also turn on t he service posit ion,
for example, if yo u want to p rotect the
w indshield from icing by using a cover.
- The service posit io n moves to
off auto­
matically whe n yo u operate the w ind­
shield wiper lever, or speed exceeds
4 mph (6 km/h).
Replacing front wiper blades
Wiper blades in good condition help keep the
windshi eld clear .
Fig. 5 9 Unlatching w ipe r blades
®"
Fig. 60 Remov ing w iper blades

58 Clear vis ion
Removing the wiper blade
.. Move the wipers to the service position
c::>page 57.
.. Fo ld the windshield wiper arm away from
the g lass.
.. On the upper end of the wiper arm at the
corrugation, squeeze the plast ic retainer to­
gether on both sides in the direction of the
arrow
c::> fig. 59 .
.. Rotate the w iper blade in the direct ion of
the arrow @c::>
fig. 60 away from the w iper
arm.
.. Lift the w iper blade
off in the direc tion of
the arrow @.
Attaching the wiper blade
.. Place the rounded end of the wiper onto the
end of the w iper arm in the
oppo site direc­
t ion to the ar row @
c::> fig. 60.
.. Swing the wipe r in the oppo site direct io n to
the arrow @onto the wiper arm.
.. Sq ueeze the corrugation on the w iper until
yo u hear it click in the wiper arm.
.. Fold the wiper arm back onto the wind­
shield .
.. Switch the ignition on and move the w iper
lever down briefly . The wiper will move back
to the park pos it ion .
The front wiper b lades measure left s ide
23 .20 in . (S90 mm) and rig ht side 18 .SO in.
(470 mm) i n length,
C lean your wiper blades regu larly with a wind­
shie ld washer solution to prevent streaking . If
the blades are very d irty, for example with in­
sects, carefu lly clean the blades w ith a sponge
or a soft b rush.
If the wiper b lades beg in to streak the wind­
shield, this could be caused by res idue left on
the w indshield by automat ic car washes .
F ill the windsh ield washer container with a
specia l so lution available at your author ized
Aud i deale r to remove the residue .
Be s ure to inspect the condition of your w iper
b lades regularly. For safety reasons, replace
your w iper blades once or twice a year if nee- essa
ry . See yo ur authorized Aud i dea ler for re ­
placement blades .
A WARNING
-- Clean your w iper blades reg ularly with a
w indshie ld washer so lution to prevent
streaking. If the w iper blades are very
d irty, fo r example with insects , ca refully
clean the wiper blades wi th a sponge or a
soft brus h .
- For your safety , you should replace the
wiper blades onc e or twice a year . Se e
your aut hor ized Audi dealer for replace­
men t blad es.
0 Note
-The wiper b lades may only be c hanged
c::> page 57 in the service posit ion! Ot he r­
w ise, you risk damag ing the pa int on t he
hood or the w indshie ld wi per mo to r.
- Yo u should not move your veh icle o r
press t he winds hield wiper leve r when
t he wipe r arms are folded away from the
w indshield. The windsh ield wipers wo uld
move back into their or iginal position
and co uld damage the hoo d and wind­
shield.
- To help prevent dama ge to the w iper sys­
tem, always loosen blades which are fro­
zen to the windshield before operating
w ipers.
- To help prevent damage to wiper b lades,
do not use gaso line, kerosene, paint
thinner, or other solvents on o r near the
w iper blades .
- To help prevent damage to the w iper
arms or other components, do not at­
tempt to move the wipe rs by hand .
(D Tips
-Commercial hot waxes applied by auto­
matic ca r washes affect the cleanability
of the g lass s urface .
- Yo u can also use the service position, for
examp le, if yo u want to p rotect the
w indshield from icing by using a cover. ..,_

-You cannot activate the service position
when the hood is open.
- The front wiper blades a re different
l engths; the blade on the driver's side is
l onger.
Changing the rear wiper blade
F ig . 6 1 Insta lling/re moving wiper blade
Removing the wiper b lade
.. Fo ld the windshield wipe r arm away from
the g lass .
.. Pull the met al surround of the w iper blade
out o f the retaine r in the d irection o f the ar­
row
r=> fig. 61. Hold the wiper arm firmly by
the upper end as you do this.
Attaching the wiper blade
.. Adjus t the posi tion of the wipe r blade in the
retainer
r=> fig. 61 (see close up).
.. Press the w iper blade into the retainer. Hold
t h e wiper arm firmly by the upper end as
you do this .
.. Fo ld the wiper arm back onto the glass.
A WARNING
- To avoid streaks, you should clean the
windshield wiper blades regular ly w ith
w indow cleaner. Fo r heavy soiling, for ex­
ample, insects, the wipe r blades can also
be cleaned with a sponge or a cloth.
- For safety reasons, the windsh ield wiper
blades sho uld be replaced once or twice
a year .
Clear vision 59
Digital compass
Activating or deactivating the compass
App lies to vehicles: wi th digi tal co mpass
The direction is displayed on the interior rear
view mirror .
Fig. 62 Inside rear v iew mirror : d ig ita l compass act i­
vated
.. To activate or deactivate, hold the@ but­
ton down unt il the red display appears or
disappears .
The dig ital compass only works w ith the igni­
tion turned on. The directions are displayed as
initials :
N (North), NE (Northeast), E (East),
SE (So utheast), S (South), SW (Southwest),
W (West), NW (Northwest) .
(0 Tips
To avoid inaccurate d irect io ns, do not al­
l ow any remote contro ls, electr ica l sys­
tems, o r metal parts close to the mir ror.

60 Clear vis ion
Setting the magnetic deflection zone
A ppl ies to vehicles: with digital compass
The correct magnetic deflection zone must be
set in order to display the directions correctly.
©
Fig. 63 North America: magnet ic def lect ion zone
boundaries
• Hold the@~ page 59, fig. 62 button down
u ntil the number of the set magnetic deflec­
tion zone appears on the interior rear view
mirror .
• Adjust the magnetic deflection zone by re­
peatedly pressing on the @button. The set
mode automatically deactivates after a few
seconds .
Calibrating the compass
Applies to vehicles: with digital compass
The compass has to be recalibrated if the dis­
play is wrong or inaccurate.
• Hold the@ button down until the letter C
is displayed on the interior rear view m irror .
• Drive in a circle at a speed of about 5 mph
(10 km/h) until a d irection is shown on the
i nterior rear view m irror.
A WARNING
-
The digital compass is to be used as a di-
rectional aid only. Even though you may
want to look at it while you are driving, you
must still pay attent ion to traffic, road and
weather conditions as well as othe r possi­
b le ha zards.

Seats and storage
General recommen­
dations
Why is your seat adjustment so important?
The safety belts and the airbag system can
only provide maximum protection if the front
seats are correctly adjusted.
There are several different ways you can ad­
just the driver's seat and the front passenger's seat so that it conforms to your body size.
It is
especia lly important that the seat be adjusted
properly so that:
- you can easily and quick ly reach all the
switches and controls in the instrument
panel
- your body is properly supported thus reduc­
ing physical stress and fatigue
- the safety belts and airbag system can offer
maximum protection ¢
page 122
In the following chapte rs, you will see exactly
how you can best adjust your seats.
There are special regulations and instructions
for installing a child safety seat on the front passenger's seat. Always heed the informa­
tion regard ing child safety provided in
¢ page 143, Child Safety .
A WARNING
Incorrect seating position of the driver and
all other passengers can result in serious
personal injury.
- Always keep your feet on the f loor when
the vehicle is in motion -never put your
feet on top of the instrument panel, out of the w indow or on top of the seat cush­
ion! This applies espec ially to the passen­
gers.
If your seating position is incorrect
you increase the r isk of injury in the case
of sudden braking or an acc ident. If the
airbag infla tes and the seating posi tion
is incorrect this could result in personal
injury or even death.
S eat s an d sto rage 61
-It is important for both the driver and
front passenger to keep a distance of at
least 10 inches (25 cm) between them­
selves and the steering wheel and/or in­
strument panel.
If you're s itting any
closer than th is, the airbag system can­
not protect you prope rly. In addition to
this, the front seats and head restra ints
m ust be adjusted to yo ur body height so
that they can give you maximum protec ­
tion.
'
- Always try to keep as much distance as
possible between yourself and the steer­
ing wheel or instrument pane l.
- Do not adjust the driver's or front pas­
senger's seat whi le the vehicle is moving .
Your seat may move unexpected ly, caus­
ing sudden loss of veh icle control and
personal injury. If you adjust your seat
while the veh icle is moving, you are out
of posit ion .
Driver's seat
The correct seat position is important for safe
and relaxed driving .
We recommend that you adjust the driver 's
seat in the fo llow ing manner :
.. Adjust the seat in fo re and aft direction so
that you can easily push the peda ls to the
floor wh ile keeping your knees slight ly bent
¢ .& in Why is your seat adjustment so im­
portant? on page 61.
.. Adjust the seatback so that when you sit
w ith your back against the seatback, you can
st ill grasp the top of the steering wheel.
.. Adjust t he head restra int so the upper edge
is as even as possible wi th the top of your
head . If that is not poss ible , try to adjust
the head restraint so that it is as close to
this position as possib le
<=:> page 65.
A WARNING
-Never place any objects in the dr iver's foot-
well. An object could get into the pedal
area and interfere with pedal funct ion. In

62 Seats and storage
case of sudden braking or an accident, you
would not be ab le to brake or acce lerate!
Front passenger's seat
Always move the front passenger seat into
the rearmost position.
To avo id contact with the airbag wh ile i t is de ­
p loying, do not sit a ny closer to the inst ru ­
ment panel than necessary and always wear
the three-point safety be lt provided adjusted
correctly. We recommend that you adjust the passenger's seat in the following manner:
... Move the front passenger seat into the rear ­
most position of the fore and aft adjustment
range
¢ .&.. in Why is your seat adjustment
so important? on page
61.
... Bring the backrest up to an (almost) upright
pos it ion .
Do not ride w ith the seat reclined.
... Adjust the head restraint so the upper edge
i s as
even as possible with the top of your
head. If that is not possib le, try to adjust
the head rest raint so that it is as close to
t h is position as possible
¢ page 65.
... Place your feet on the f loor in front of the
passenger's seat.
Adjusting front seats manually
Adjustment controls
Applies to vehicles: with manual seat adjustme nt
Various controls on the manual seats provide
a wide range for individual adjus tments.
==""" -®
Fig . 6 4 Ad just ment contro ls: locat ions on drive r"s seat
CD Moving the seat forward or backward
@ Adjusting the seat height
@ Adjusting the seatback ang le
@ Adjusting head restraint height
Some of the co ntrols are fitted on certain
models on ly or they are optiona l equipment.
Adjusting the manual seats
Applies to vehicles: with manual seat adjust ment
Position, angle and shape of the manual
seats can be adjusted to provide safe and
comfortable seating.
Rea d and heed all WARNINGS ¢.&.. befo re
you adjust yo ur seat .
Moving the front seats forward or
backward
"' Lift the leve r¢ page 62, fig. 64 CD and slide
the seat to the desired position .
... Release the lever and then move the seat
further until you feel and hear it engage .
Ad justing the seat height
... Pull the lever @up and pump it to raise the
seat.
... Push the lever down and pump it to lower
the seat.
Adjusting the seatback angle
... Lean forward to take your weight off the
seatback .
... Tur n the hand wheel@ in the di rection yo u
want the seatback to tilt.
A WARNING
- Never adjust the driver's or front pas­
senger's seat whi le the vehicle is moving.
If you do th is while the veh icle is moving,
you will be out of position . Always adjust
the dr iver's or front pass enge r's seat
when the vehi cle is not mov ing.
- Be careful when adj usting the seat
he ight. Check to see that no one is in t he
way, or ser io us inju ry co ul d result!
- To reduce the risk of injury in the case of
sudden b raking o r acciden t, front pas­
senge rs mus t never r ide in a mov ing
ve­
h icle with the seatback reclined . Sa fety

belts and the airbag system only offer
maximum protection when the seatback
is upright and the safety belts are prop­
erly positioned on the body . The more
the seatback is reclined, the greater the
risk of personal injury from an incorrect
seating pos it ion and improperly posi­
tioned safety belts!
Adjusting the power
seat
Adjustment switches
Ap plies to vehicles: with power driver seat
For an in tuitive operation, the swi tches @
and @ are distinctly shaped and positioned
to reflect their adjustment functions .
Fig. 65 Adjust men t sw it c h es : locat ions on driver 's seat
Push or pull e ither switch in exactly the same
direction you like the corresponding part of
the seat to mov e.
@ Moving the seat forward or backward
@ Adjusting the angle of the seatback and
he ad restraints
© Adjust ing the lumbar support
Seats and storage 63
Power seat adjustment
Applies to vehicles: with power driver seat
The switches can be moved in various direc­
tions to allow precise adjustment.
Fig. 66 Sea t cush io n adju stme nt: sw it c h m otions
Push or pull the switch in the same direction
you like the seat cushion to move.
Moving the entire seatback or forward
.,. Push the switch back at the tip or forward
at the rear@c::>
,&..
Adjusting the seat height
.,. To raise the sea t, pull t he switch at both
ends, @
and@ c::> ,&. .
.,. To lower the seat, push the switch down
evenly,
@ and @<=:>,&. .
Tilting the seat cushion back or forward
.,. To tilt ba ck the seat cushion, pull the switch
a t the fron t only, @ c::> ,&. .
.,. Alternatively, push the switch at the rear
only,
@ <=:> ,&. .
.,. To tilt forward the seat cushion, push the
sw itch
at the front only@ Q ,&..
.,. Alternatively, pull the switch at the rear on­
ly @
Q ,&. .
A WARNING
-Never adjust the driver's seat while the
vehicle is moving. If you do this whi le the
veh icle is moving, you will be out of posi­
tion . Always adjust the driver 's seat
when the vehicle is not mov ing.
- Be careful when adjusting the seat
height. Check to see that no one is in the
way, or serious injury could result!