2012 Alfa Romeo MiTo lock

GETTING TO KNOW YOUR CAR7
1DASHBOARD
The presence and position of controls, instruments and gauges may vary according to different versions.
1. Air vent for side windows - 2. Adjustable air vent - 3. Exterior lighting control lever - 4. Instrument panel - 5. Windscreen wiper/rearscreen
wiper/trip computer control lever - 6. Radio (for versions/markets, where provided) - 7. Adjustable air vents - 8. Hazard warning lights,
door lock/unlock button - 9. Passenger front air bag - 10. Glove compartment - 11. Heating/ventilation/climate control system controls
12. Gearbox lever - 13. “Alfa DNA” system - 14. Ignition device - 15. Driver front knee air bag (for versions/markets, where provided)
16. Driver front air bag - 17. Cruise Control lever (for versions/markets, where provided) - 18. Fuse box access flap - 19. Control panel.
A0J0330mfig. 1

12GETTING TO KNOW YOUR CAR
EBD failure (red)/(amber)
If warning lights xand>are lit up at the same
time with the engine running, this indicates an EBD
system failure or that the system is not available. Ear-
ly locking of the rear wheels may occur in the event
of violent braking, causing the car to swerve.
Under these circumstances drive with extreme caution
straight to the nearest Alfa Romeo Authorised Service to
have the system checked. The display will show the dedicated mes-
sage.x
>
Brake pad wear (amber)
The warning light (or symbol on the display) lights up
when the one or more brake pads show signs of wear;
under these circumstances have them replaced as soon
as possible. The display shows the dedicated message. It is advis-
able to have this operation carried out by an Alfa Romeo Autho-
rised Service. d
ABS system failure (amber)
This warning light comes on when the ignition key is
turned to MAR, but it should go off after a few sec-
onds. The warning light (or symbol on the display) lights
up when the system is inefficient. Under these circumstances the
braking system will work as normal without the extra performance
offered by the ABS system. Drive with caution and visit an Alfa
Romeo Authorised Service at your earliest convenience. The display
will show the dedicated message.>

20GETTING TO KNOW YOUR CAR
Possible presence of ice on the road
On versions equipped with “Reconfigurable multi-
functional displays ” a message + symbol on the dis-
play are shown when the outdoor temperature falls to or
below 3°C.
On versions with “Multifunctional displays” only the dedicated mes-
sage is shown.
IMPORTANT In the event of the failure of the outdoor temperature
sensor, dashes are shown on the display instead of a temperature
value.√
Fuel lock
On some versions the display will show a message +
symbol if the fuel lock engages. For the fuel lock sys-
tem reactivation procedure see paragraph "Fuel cut-off
system" in this chapter.s
External lights failure
On some versions the display will show a message +
symbol if a fault is detected in one of the following
lights:
– daytime lights (DRL)
– side lights
– direction indicators
– rear fog lights
– number plate lights.
The fault may be caused by: one or more burnt bulbs, a blown pro-
tection fuse or an interruption of the electrical connection.W
Brakes lights failure
On some versions the display will show a message +
symbol if a fault is detected in the brake lights. The
fault may be caused by a burnt bulb, a blown protec-
tion fuse or an interruption of the electrical connection.T

22GETTING TO KNOW YOUR CAR
Speed limit exceeded (red)
(for versions/markets, where provided)
This warning light (for versions/markets, where pro-
vided) comes on when the vehicle speed exceeds 120
km/h.
When the vehicle exceeds the speed limit set in the Setup Menu
(e.g. 120 km/h), on some versions a message and symbol are
shown in the display and a buzzer sounds.
X
General failure (amber)
(for versions/markets, where provided)
On some versions, this warning light comes on under the
following circumstances:
External lights failure
See description of 6warning light.
Brake lights failure
See description of “brake lights failure”.
Fuel lock
This warning light comes on when the fuel cut-off inertia switch is
triggered. The display will show the dedicated message.
è
Particulate trap filter blocked
(Diesel with DPF versions) (amber)
When the ignition key is turned to MAR, the warning
light switches on but it must switch off after a few seconds.
The warning light comes on constantly to notify the driver that
the DPF system needs to eliminate captured pollutants (particu-
late) by the regeneration process. The warning light does not come
on during every DPF regeneration, but only when driving conditions
require notification of the driver. To switch the warning light off,
the car must stay in motion until regeneration has been complet-
ed. The process normally takes about 15 minutes. The optimum
conditions to end the process are achieved by keeping the car in
motion up to 60km/h with an engine speed higher than 2,000
rpm. This light coming on is not a car defect and therefore the car
does not need to go to the workshop.
A specific message will appear on the display when the warning
light comes on (for versions/markets, where provided).
h
Always drive at a speed appropriate to the traffic
conditions, the weather and speed limits. The en-
gine may be turned off while the DPF light is on;
however, repeated interruption of the regeneration process
may result in premature exhaustion of engine oil. For this
reason it is always advisable to wait for the light to go
off before turning off the engine, following the instruc-
tions appearing above. It is not advisable to complete DPF
regeneration with the vehicle stationary.

26GETTING TO KNOW YOUR CAR
DISPLAY
The car may be equipped with the multifunctional display/multi-
functional reconfigurable display which, in accordance with the set-
tings made, can display useful information when driving.
MULTIFUNCTIONAL DISPLAY “STANDARD”
SCREEN fig. 6
The following information is shown on the display:
A. Date
B. Odometer (covered km or miles).
C. Driving mode selected via “Alfa DNA” (dynamic vehicle con-
trol system) (for versions/markets, where provided)
– d = Dynamic
– n = Normal
– a = All Weather
D. Clock (always displayed, even with ignition key removed and
the doors closed)
E. Start&Stop function indication (for versions/markets, where
provided)
F. Outdoor temperature
G. Gear Shift Indicator (for versions/markets, where provided)
H. Headlight alignment position (with dipped beam headlights on
only)
With the ignition key removed, when a door is opened/closed, the
display is activated and shows the time and total mileage (in km
or miles) for a few seconds.
fig. 6A0J1270g

34GETTING TO KNOW YOUR CAR
Trip B data (Trip B enablement)
Through this option it is possible to activate (On) or deactivate
(Off) the Trip B (partial trip) display.
For further information see the “Trip computer” paragraph.
For activation / deactivation, proceed as follows:
– briefly press MENU ESC: (On) or (Off) will flash on the display
(according to previous setting);
– press + or – to change the setting;
– briefly press the MENU ESC button to go back to the menu screen
or hold the button down to go back to the standard screen with-
out storing the new settings.
Set time (Clock)
With this function it is possible to set the clock through two sub-
menus: “Time” and “Mode”.
Proceed as follows:
– briefly press MENU ESC: the display will show two sub-menus
“Time” and “Mode”;
– press + or – to switch between the two sub-menus;
– once you have selected a sub-menu, press MENU ESC briefly;
– when accessing the “Time” submenu: briefly press MENU ESC:
“hours” will flash on the display;
– press + or – to change the setting;
– briefly press MENU ESC: “minutes” will flash on the display;
– press + or – to change the setting.
IMPORTANT The setting increases or decreases by one unit each
time + or – is pressed. Hold down the button to increase/decrease
the setting rapidly. Complete the setting by briefly pressing the but-
ton when you are close to the required setting.

GETTING TO KNOW YOUR CAR37
1
Autoclose (Automatic door lock operation
with car running)
When activated (On), this function automatically locks the doors
when the car speed exceeds 20 km/h.
Proceed as follows to switch this function on or off:
-– briefly press MENU ESC to display a submenu;
– briefly press MENU ESC: (On) or (Off) will flash on the display
(according to previous setting);
– press + or – to change the setting;
– briefly press the MENU ESC button to go back to the submenu
screen or hold the button down to go back to the main menu screen
without storing the new settings;
– hold down MENU ESC to go back to the standard screen or main
menu, depending on which point in the menu you have reached.
Units (Set unit of measurement)
This function may be used to set the units of measurement via
three submenus: “Distances”, “Fuel consumption” and “Temper-
ature”.
To set the required unit of measurement proceed as follows:
– briefly press MENU ESC to display the three sub-menus;
– press + or – to switch between the three sub-menus;
– once you have selected a sub-menu you wish to update, press
MENU ESC briefly;
– when accessing the “Distance” submenu: briefly press MENU
ESC: either “km” or “mi” will appear on the display (according
to the previous setting);
– press + or – to change the setting;
– when accessing the “Fuel consumption” submenu: briefly press
MENU ESC: either “km/l ”, “l/100km” or “mpg” will appear
on the display (according to the previous setting);

42GETTING TO KNOW YOUR CAR
Courtesy lights (Activation/deactivation of
“Courtesy lights”)
(for versions/markets, where provided)
This function allows the side lights, number plate lights and inter-
nal courtesy lights to be lit up for approximately 25 seconds when
the doors or luggage compartment are opened using the remote
control, with the following exceptions:
❍interruption after 5 seconds following doors closure
❍interruption following a locking operation using the remote con-
trol
❍interruption following any operation using the remote control
To activate / deactivate this function, proceed as follows:
– briefly press MENU ESC: “On” or “Off” will flash on the dis-
play (according to previous setting);
– press + or – to change the setting;
– briefly press the MENU ESC button to go back to the menu screen
or hold the button down to go back to the standard screen with-
out storing the new settings.
Exit Menu
This is the last function that closes the setting cycle listed in the ini-
tial menu screen. Briefly press MENU ESC to go back to the stan-
dard screen without storing new settings. Press – to return to the
first menu item.
TRIP COMPUTER
GENERAL FEATURES
The “Trip computer” is used to display information on car opera-
tion when the key is turned to MAR. This function allows you to
define two separate trips called “Trip A” and “Trip B” to monitor
the car’s complete mission (trip) in a mutually independent man-
ner. Both functions can be reset (reset - start of new mission).
“Trip A” can be used to display figures relating to:
– Range
– Distance travelled
– Average fuel consumption
– Instantaneous fuel consumption
– Average speed
– Travel time (driving time).
The “Trip B” function is used to display information relating to:
– Distance travelled B
– Average fuel consumption B
– Average speed B
– Travel time B (driving time).
“Trip B” functions may be excluded (see paragraph on “Trip B on”).
“Range” and “Instantaneous fuel consumption” cannot be reset.