2012.5 Peugeot RCZ ignition
[x] Cancel search: ignitionPage 58 of 336
56
ALARM *
System which protects and provides a deterrent against theft and
break-ins. It provides the following types of monitoring.
- exterior perimeter
The system checks for opening of the vehicle.
The alarm is triggered if anyone tries to open a door, the boot, the
bonnet...
- interior volumetric
The system checks for any variation in the volume in the passenger compartment.
The alarm is triggered if anyone breaks a window, enters the passenger
compartment or moves inside the vehicle.
- tilt
The system checks for any change in the attitude of the vehicle.
The alarm is triggered if the vehicle is lifted, moved or knocked.
For all work on the alarm system, contact a PEUGEOT dealer or a
qualifi ed workshop.
LOCKING THE VEHICLE WITH FULL ALARM
SYSTEM
Activation
)
Switch off the ignition and get out of the vehicle.
)
Press the locking button on the remote control.
The monitoring system is active: the indicator lamp in the button fl ashes
once per second.
After the locking button on the remote control is pressed, the exterior
perimeter monitoring is activated after a delay of 5 seconds and the
interior volumetric and anti-tilt monitoring after a delay of 45 seconds.
Deactivation
)
Press the unlocking button on the remote control.
The alarm system is deactivated: the indicator lamp in the button goes off.
Self-protection function
The system checks for the putting out of service of its
components.
The alarm is triggered if the battery, the central control or the siren
wiring are put out of service or damaged.
* According to country. If an opening (door, boot...) is not closed fully, the vehicle is not
locked but the exterior perimeter monitoring will be activated after
a delay of 45 seconds at the same time as the interior volumetric
and anti-tilt monitoring.
Page 59 of 336
2/
ACCESS
LOCKING THE VEHICLE WITH EXTERIOR
PERIMETER MONITORING ONLY
Deactivation of the interior volumetric and anti-tilt monitoring
)
Switch off the ignition.
)
Within ten seconds, press the button until the indicator lamp is on
continuously.
)
Get out of the vehicle.
)
Press the locking button on the remote control immediately.
The exterior perimeter monitoring alone is activated: the indicator lamp
in the button fl ashes once per second.
Reactivation of the interior volumetric and anti-tilt monitoring
)
Press the unlocking button on the remote control to deactivate the
exterior perimeter monitoring.
)
Press the locking button on the remote control to activate all the
monitoring functions.
The indicator lamp in the button again fl ashes once per second.
Deactivate the interior volumetric and anti-tilt monitoring to avoid
unwanted triggering of the alarm in certain cases such as:
- leaving a pet in the vehicle,
- leaving a window partially open,
- washing your vehicle,
- changing a wheel,
- having your vehicle towed,
- transport by sea. To be effective, this deactivation must be carried out each time
the ignition is switched off.
Page 60 of 336
58
OPERATING FAULT
LOCKING THE VEHICLE WITHOUT ACTIVATING
THE ALARM
)
Lock or deadlock the vehicle using the key in the driver's door lock.
When the ignition is switched on, fi xed illumination of the indicator lamp
in the button indicates a fault with the system.
Have it checked by a PEUGEOT dealer or a qualifi ed workshop.
FAILURE OF THE REMOTE CONTROL
To deactivate the monitoring functions:
)
unlock the vehicle using the key in the driver's door lock,
)
open the door; the alarm is triggered,
)
switch on the ignition; the alarm stops; the indicator lamp in the
button goes off.
TRIGGERING OF THE ALARM
The monitoring functions remain active until the alarm has been
triggered eleven times in succession.
When the vehicle is unlocked using the remote control, rapid
fl ashing of the indicator lamp in the button informs you that the
alarm was triggered during your absence. When the ignition is
switched on, this fl ashing stops immediately.
This is indicated by sounding of the siren and fl ashing of the direction
indicators for thirty seconds.
2 minutes after closing the last door or the boot, the system is activated
automatically.
)
To avoid triggering the alarm when entering the vehicle, fi rst press
the remote control unlocking button.
AUTOMATIC ACTIVATION *
* Depending on country of sale.
Page 61 of 336
2/
ACCESS
ELECTRIC WINDOWS
Fitted with a safety anti-pinch system.
A.
Left-hand electric window control switch.
B.
Right-hand electric window control switch.
ONE-TOUCH ELECTRIC WINDOWS
There are two options:
- manual mode
)
Press or pull the switch gently. The window stops when the
switch is released.
- automatic mode
)
Press or pull the switch fi rmly. The window opens or closes fully
when the switch is released.
)
Pressing the switch again stops the movement of the window.
The electric window switches remain operational for approximately
45 seconds after the ignition is switched off or until the vehicle is
locked after a door is opened.
If the passenger's window cannot be operated from the driver's
door control panel, carry out the operation from the control panel
of the passenger door.
After approximately ten consecutive complete opening/closing
movements of the window, a protection function is activated which
only authorises closing of the windows, so as to prevent damage
to the electric window motor.
Once the window is closed, the switches will become operational
again after approximately 40 minutes.
Safety anti-pinch
When the window rises and meets an obstacle, it stops and partially
lowers again.
If the window cannot be closed (for example, in the presence of
ice), immediately after the movement is reversed:
)
press and hold the switch until the window opens fully,
)
then pull the switch immediately and hold it until the window
closes,
)
continue to hold the switch for approximately one second after
the window has closed.
The safety anti-pinch function is not operational during these
operations.
Page 62 of 336
60
Reinitialisation
If a window does not rise automatically, its operation must be
reinitialised:
)
pull the switch until the window stops,
)
release the switch and pull it again until the window closes fully,
)
continue to hold the switch for approximately one second after the
window has closed,
)
press the switch to lower the window automatically to the low
position,
)
when the window has reached the low position, press the switch
again for approximately one second.
The safety anti-pinch function is not operational during these
operations.
Always remove the key from the ignition when leaving the vehicle,
even for a short time.
If an obstacle is encountered during operation of the electric
windows, you must reverse the movement of the window. To do
this, press the switch concerned.
When the driver operates the switch for the passenger's electric
window, they must ensure that no one is preventing correct
closing of the windows.
The driver must ensure that the passengers use the electric
windows correctly.
Be aware of children when operating the windows.
Page 65 of 336
2/
ACCESS
Pressing the central locking control unlocks the vehicle.
Opening a door from the inside, when stationary, also unlocks
the vehicle, but the vehicle will be locked again when the speed
exceeds 6 mph (10 km/h).
Activation / Deactivation
You can activate or deactivate this function.
)
With the ignition on, press the button for more than two seconds.
A confi rmation message appears in the screen.
In the event of a serious impact with deployment of an airbag, the
vehicle's doors unlock automatically to allow the occupants to leave the
vehicle.
EMERGENCY LOCKING
To lock or unlock the doors mechanically in the event of a central
locking system failure or fl at battery.
Locking the driver's door
)
Insert the key in the lock, then turn it to the right.
Unlocking the driver's door
)
Insert the key in the lock, then turn it to the left.
Locking the passenger door
)
Using the key, remove the black cap on the edge of the door.
)
Insert the key in the cavity without forcing, then without turning it,
move the the latch sideways towards the interior of the door.
)
Remove the key and refi t the cap.
Unlocking the passenger door
)
Pull the interior door opening control.
ANTI-INTRUSION SECURITY
This function permits automatic and simultaneous locking of the doors,
boot lid and fuel fi ller fl ap as soon as the vehicle speed exceeds 6 mph
(10 km/h).
Operation
If one of the doors is open, the automatic central locking does not take
place.
If the boot lid is open, the automatic central locking of the doors is
active.
Page 68 of 336
66
FRONT SEATS
Seat with integral head restraint, consisting of a seat cushion and a
seat back which can be adjusted to adapt your position for ease of
driving and comfort.
ELECTRIC ADJUSTMENTS
Forwards-backwards adjustment
Seat cushion height adjustment
)
Push the control forwards or rearwards to slide the seat.
)
Tilt the rear part of the control upwards or downwards to obtain
the required height.
The electrical functions of the seat are deactivated approximately
one minute after the ignition is switched off.
To reactivate them, switch on the ignition.
Seat back angle adjustment
)
Tilt the control forwards or rearwards to adjust the angle of the
seat back.
Page 70 of 336
68
STORING DRIVING POSITIONS
System which takes into account the electrical settings of the driver's
seat and the door mirrors. It enables you to store two positions using
the buttons on the side of the driver's seat.
STORING A POSITION
Using buttons M / 1 / 2
)
Switch on the ignition.
)
Adjust your seat and your door mirrors.
)
Press button M
, then press button 1
or 2
within four seconds.
An audible signal is heard indicating that the settings have
been stored.
RECALLING A STORED POSITION
Storing a new position cancels the previous position.
Using button 1 or 2
)
Press and hold button 1
or 2
until the audible signal is heard
indicating the end of the adjustment.
When the ignition is off, after a few consecutive position recalls,
the function will be deactivated until the engine is started, to
prevent discharging of the battery.