2011 YAMAHA YFM250R-W low beam

Checking and lubricating the cables ........ 8-32
Checking and lubricating the brake and
clutch levers ........................................... 8-33
Checking the shift pedal ........................... 8-34
Checking and lubricating the brake
pedal ...................................................... 8-34
Checking the wheel hub bearings ............ 8-34
Lubricating the swingarm pivots ............... 8-34
Lubricating the upper and lower arm
pivots ...................................................... 8-34
Lubricating the steering shaft ................... 8-35
Battery ...................................................... 8-36
Replacing the fuse ................................... 8-38
Headlight bulb .......................................... 8-39
Headlight beam ........................................ 8-40
Replacing the tail/brake light bulb ............ 8-40
Replacing a turn signal light bulb ............. 8-40
Auxiliary light bulb .................................... 8-41
Removing a wheel .................................... 8-41
Installing a wheel ...................................... 8-42
Troubleshooting ....................................... 8-43
Troubleshooting chart .............................. 8-44
CLEANING AND STORAGE .......................... 9-1
Cleaning ..................................................... 9-1
Storage ....................................................... 9-2SPECIFICATIONS .......................................10-1
CONSUMER INFORMATION.......................11-1
Identification numbers ...............................11-1
U33B70E0.book Page 3 Wednesday, June 11, 2008 1:38 PM

4-4
4
NOTICEECB00050See the starting instructions on page 6-1 priorto starting the engine.EBU28061Light switch“//”
Set the switch to “ ” to turn on the high beam.
Set this switch to “ ” to turn on the low beam.
Set the switch to “ ” to turn off the headlight.NOTICEECB00030Do not use the headlight with the engine turned
off for an extended period of time, otherwise
the battery may discharge to the point that the
starter motor will not operate properly. If this
should happen, remove the battery and re-charge it.EBU27990Turn signal switch“/”
To signal a right-hand turn, push this switch
to “ ”. To signal a left-hand turn, push this switch
to “ ”. When released, the switch returns to the
center position. To cancel the turn signal lights,
push the switch in after it has returned to the center
position.
EBU18170Horn switch“”
Press the switch to sound the horn.EBUM0220Hazard switch“”
Turn this switch to “ ” to turn on the hazard lights
(simultaneous flashing of all turn signal lights).
The hazard lights are used in case of an emergen-
cy or to warn other drivers when your vehicle is
stopped where it might be a traffic hazard.NOTICEECB00860Do not use the hazard lights for an extended
length of time with the engine not running, oth-erwise the battery may discharge.EBU18280Throttle lever Once the engine is running, movement of the throt-
tle lever will increase the engine speed.
Regulate the speed of the ATV by varying the
throttle position. Because the throttle is spring-
loaded, the ATV will decelerate, and the engine will
return to an idle any time the hand is removed from
the throttle lever.
U33B70E0.book Page 4 Wednesday, June 11, 2008 1:38 PM

8-40
8
EBU28170Headlight beam If a headlight beam adjustment is necessary, have
a Yamaha dealer perform it.EBU25600Replacing the tail/brake light bulb If the tail/brake light bulb burns out, replace it as
follows.
1. Remove the lens by removing the screws.
2. Remove the defective bulb by pushing it in
and turning it counterclockwise.3. Insert a new bulb into the socket, push it in,
and then turn it clockwise until it stops.
4. Install the lens by installing the screws.
NOTICEECB00700Do not overtighten the screws, otherwise thelens may break.EBU28030Replacing a turn signal light bulb 1. Remove the turn signal light lens by removing
the screw.
1. Screw
1
1. Tail/brake light bulb
1
U33B70E0.book Page 40 Wednesday, June 11, 2008 1:38 PM