Page 27 of 140
4-9
4
WARNING
EWB00220Always set the parking brake before starting
the engine. The ATV could start moving un-
expectedly if the parking brake is not ap-
plied. This could cause loss of control or a
collision.Always be sure you have released the park-
ing brake before you begin to ride. The brake
could overheat if you ride the ATV without re-
leasing the parking brake. You could lose
braking performance which could cause an
accident. You could also wear out the brakesprematurely.EBU18530Shift pedal This ATV is equipped with a constant-mesh 5-
speed transmission. The shift pedal is located on
the left side of the engine and is used in combina-
tion with the clutch when shifting.
EBU18720Fuel tank cap Remove the fuel tank cap by turning it counter-
clockwise.1. Shift pedal
1
U33B70E0.book Page 9 Wednesday, June 11, 2008 1:38 PM
Page 31 of 140
4-13
4 Move the starter (choke) in direction (b) to turn off
the starter (choke).
See the “Starting a cold engine” section on page
6-1 for proper operation.
EBU28010Steering lock To lock the steering
1. Turn the handlebar all the way to either side.
2. Open the steering lock cap, and then insert
the steering lock key.
3. Turn the key 1/8 turn counterclockwise, push
it in, and then turn the key 1/8 turn clockwise.
4. Check that the steering is locked, remove the
key, and then close the steering lock cap.
1. Starter (choke)
(a)(b)1
1. Steering lock cap
2. Steering lock1
2
U33B70E0.book Page 13 Wednesday, June 11, 2008 1:38 PM
Page 32 of 140
4-14
4To unlock the steering
1. Open the steering lock cap, and then insert
the key.
2. Turn the key 1/8 turn counterclockwise to re-
lease the lock.
3. Remove the key, and then close the steering
lock cap.
EBU18890Seat To remove the seat
Insert your hand between the rear of the seat and
the rear fender, pull the seat lock lever upward and
pull up the seat at the rear.To install the seat
Insert the projections on the front of the seat into
the seat holders and push down on the seat at the
rear.
TIPMake sure that the seat is securely fitted.EBU18991Adjusting the front shock absorber as-
semblies (YFM250R-W)The spring preload can be adjusted to suit the rid-
er’s weight and the riding conditions.
Adjust the spring preload as follows.
1. Seat lock lever
1
1. Projection
2. Seat holder
1
2
U33B70E0.book Page 14 Wednesday, June 11, 2008 1:38 PM
Page 122 of 140
8-40
8
EBU28170Headlight beam If a headlight beam adjustment is necessary, have
a Yamaha dealer perform it.EBU25600Replacing the tail/brake light bulb If the tail/brake light bulb burns out, replace it as
follows.
1. Remove the lens by removing the screws.
2. Remove the defective bulb by pushing it in
and turning it counterclockwise.3. Insert a new bulb into the socket, push it in,
and then turn it clockwise until it stops.
4. Install the lens by installing the screws.
NOTICEECB00700Do not overtighten the screws, otherwise thelens may break.EBU28030Replacing a turn signal light bulb 1. Remove the turn signal light lens by removing
the screw.
1. Screw
1
1. Tail/brake light bulb
1
U33B70E0.book Page 40 Wednesday, June 11, 2008 1:38 PM
Page 123 of 140
8-41
8 2. Remove the defective bulb by pushing it in
and turning it counterclockwise.
3. Insert a new bulb into the socket, push it in,
and then turn it clockwise until it stops.
4. Install the lens by installing the screw.
NOTICEECB00870Do not overtighten the screw, otherwise thelens may break.EBU28020Auxiliary light bulb If the auxiliary light bulb burns out, have a Yamaha
dealer replace it.
EBU25651Removing a wheel 1. Place the ATV on a level surface.
2. Loosen the wheel nuts.
Front
1. Screw
1. Nut1
1
U33B70E0.book Page 41 Wednesday, June 11, 2008 1:38 PM