Page 49 of 100
PERIODIC MAINTENANCE AND ADJUSTMENT
6-3
6
EAU46861
TIP
The annual checks must be performed every year, except if a kilometer-based maintenance, or for the UK,
a mileage-based maintenance, is performed instead.
From 50000 km (30000 mi), repeat the maintenance intervals starting from 10000 km (6000 mi).
Items marked with an asterisk should be performed by a Yamaha dealer as they require special tools, data and
technical skills.
EAU46910
Periodic maintenance chart for the emission control system
ODOMETER READING
NO. ITEM CHECK OR MAINTENANCE JOBANNUAL
1000 km 10000 km 20000 km 30000 km 40000 kmCHECK
(600 mi) (6000 mi) (12000 mi) (18000 mi) (24000 mi)
1*Fuel line• Check fuel hoses for cracks or
damage.√√√ √√
2Spark plug• Check condition.
• Clean and regap.√√
• Replace.√√
3*Valves• Check valve clearance.
• Adjust.√√
4*Fuel injection• Adjust engine idling speed.√√ √ √ √ √
5*Mufflers and exhaust• Check the screw clamps for
pipeslooseness.√√ √ √ √
• Check the air cut-off valve, reed
6*Air induction systemvalve, and hose for damage.
√√√ √√
• Replace any damaged parts if
necessary.
56P-F8199-E0 30/6/10 09:24 Página 49
Page 50 of 100
PERIODIC MAINTENANCE AND ADJUSTMENT
6-4
6
EAU1770C
General maintenance and lubrication chart
ODOMETER READING
NO. ITEM CHECK OR MAINTENANCE JOBANNUAL
1000 km 10000 km 20000 km 30000 km 40000 kmCHECK
(600 mi) (6000 mi) (12000 mi) (18000 mi) (24000 mi)
1Air filter element• Replace.√√
2Clutch• Check operation.
• Adjust.√√ √ √ √
3*Front brake• Check operation, fluid level and
vehicle for fluid leakage.√√ √ √ √ √
• Replace brake pads. Whenever worn to the limit
4*Rear brake• Check operation, fluid level and
vehicle for fluid leakage.√√ √ √ √ √
• Replace brake pads. Whenever worn to the limit
5*Brake hoses• Check for cracks or damage.√√√ √√• Replace. Every 4 years
• Check runout, spoke tightness
6*Wheelsand for damage.√√ √ √ √
• Tighten spokes if necessary.
• Check tread depth and for
damage.
7*Tires• Replace if necessary.√√√ √√
• Check air pressure.
• Correct if necessary.
8*Wheel bearings• Check bearing for looseness or
damage.√√√ √
56P-F8199-E0 30/6/10 09:24 Página 50
Page 51 of 100
PERIODIC MAINTENANCE AND ADJUSTMENT
6-5
6
ODOMETER READING
NO. ITEM CHECK OR MAINTENANCE JOBANNUAL
1000 km 10000 km 20000 km 30000 km 40000 kmCHECK
(600 mi) (6000 mi) (12000 mi) (18000 mi) (24000 mi)
9*Swingarm• Check operation and for
excessive play.√√√ √
• Lubricate with lithium-soap-
based grease.Every 50000 km (30000 mi)
• Check chain slack, alignment
and condition.
Every 500 km (300 mi) and after washing the motorcycle,
10Drive chain• Adjust and lubricate chain with a
special O-ring chain lubricant riding in the rain or riding in wet areas
thoroughly.
• Check bearing play and steering
11 *Steering bearingsfor roughness.√√ √ √ √
• Lubricate with lithium-soap-
based grease.Every 20000 km (12000 mi)
12 *Chassis fasteners• Make sure that all nuts, bolts and
screws are properly tightened.√√√ √√
13Brake lever pivot
shaft• Lubricate with silicone grease.√√√ √√
14Brake pedal pivot
shaft• Lubricate with silicone grease.√√√ √√
15Clutch lever pivot • Lubricate with lithium-soap-
shaftbased grease.√√√ √√
• Check operation.
16Sidestand• Lubricate with lithium-soap-√√√ √√
based grease.
17 *Sidestand switch• Check operation.√√ √ √ √ √
56P-F8199-E0 30/6/10 09:24 Página 51
Page 52 of 100
PERIODIC MAINTENANCE AND ADJUSTMENT
6-6
6
ODOMETER READING
NO. ITEM CHECK OR MAINTENANCE JOBANNUAL
1000 km 10000 km 20000 km 30000 km 40000 kmCHECK
(600 mi) (6000 mi) (12000 mi) (18000 mi) (24000 mi)
18 *Front fork• Check operation and for oil
leakage.√√√ √
19 *Shock absorber • Check operation and shock
assemblyabsorber for oil leakage.√√√ √
Rear suspension• Check operation.√√√ √
20 *relay arm and
• Lubricate with lithium-soap-
connecting arm
√√
pivoting pointsbased grease.
• Change.
21Engine oil• Check oil level and vehicle for √√ √ √ √ √
oil leakage.
22Engine oil filter
element• Replace.√√ √
• Check coolant level and vehicle
23 *Cooling systemfor coolant leakage.√√√ √√
• Change. Every 3 years
24 *Front and rear brake
switches• Check operation.√√ √ √ √ √
25Moving parts and
cables• Lubricate.√√√ √√
• Check operation and free play.
Throttle grip • Adjust the throttle cable free
26 *housingplay if necessary.√√√ √√
and cable• Lubricate the throttle grip housing
and cable.
56P-F8199-E0 30/6/10 09:24 Página 52
Page 53 of 100
PERIODIC MAINTENANCE AND ADJUSTMENT
6-7
6
ODOMETER READING
NO. ITEM CHECK OR MAINTENANCE JOBANNUAL
1000 km 10000 km 20000 km 30000 km 40000 kmCHECK
(600 mi) (6000 mi) (12000 mi) (18000 mi) (24000 mi)
27 *Lights, signals and • Check operation.
switches• Adjust headlight beam.√√ √ √ √ √
EAUM1890
TIP
Replace the air filter element more frequently if you are riding in unusually wet or dusty areas.
Hydraulic brake service
• Regularly check and, if necessary, correct the brake fluid level.
• Every two years replace the internal components of the brake master cylinder, and change the brake fluid.
• Replace the brake hoses every four years and if cracked or damaged.
56P-F8199-E0 30/6/10 09:24 Página 53
Page 54 of 100
EAU18771
Removing and installing
panels
The panels shown need to be remo-
ved to perform some of the mainte-
nance jobs described in this chapter.
Refer to this section each time a
panel needs to be removed and insta-
lled.
EAUB1541
Panels A and B
T
o remove one of the panels
Remove the bolts, and then pull the
panel off at the areas shown.
1. Panel mounting bolt
A. Right panel
B. Left panel
To install the panel
Place the panel in the original posi-
tion, and then install the bolts.
1. Panel
2. Turn signal light coupler
3. Pin
Panels C and D
T
o remove one of the panels
Remove the bolts, and then pull the
panel off at the areas shown.
1. Panel mounting bolt
C. Right panel
D. Left panel
To install the panel
Place the panel in the original position
as shown, and then install the bolts.
Panels E and F
T
o remove one of the panels
1. Remove the bolts.
2. Remove the quick fastener and
then pull the panel off at the are-
as shown.
PERIODIC MAINTENANCE AND ADJUSTMENT
6-8
6
56P-F8199-E0 30/6/10 09:24 Página 54
Page 55 of 100
1. Panel mountign bolt
2. Quick fastener
E. Right panel
F. Left panel
To install the panel
1. Place the panel in the original
position.
2. Install the quick fastener and the
bolts.
Panel G
T
o remove the panel
Remove the bolts, and then pull the
panel off at the areas shown.
1. Panel mountign bolt
G. Panel
To install the panel
Place the panel in the original posi-
tion, and then install the bolts.
1. Panel
2. Pin
EAU19604
Checking the spark plug
The spark plug is an important engine
component, which is easy to check.
Since heat and deposits will cause
any spark plug to slowly erode, the
spark plug should be removed and
checked in accordance with the
periodic maintenance and lubrication
chart. In addition, the condition of the
spark plug can reveal the condition of
the engine.
To remove the spark plug
1. Remove the spark plug cap.
1. Spark plug cap
2. Spark plug wrench
PERIODIC MAINTENANCE AND ADJUSTMENT
6-9
6
56P-F8199-E0 30/6/10 09:24 Página 55
Page 56 of 100
2. Remove the spark plug as
shown, with the spark plug
wrench included in the owner’s
tool kit.
To check the spark plug
1. Check that the porcelain insula-
tor around the center electrode of
the spark plug is a medium-to-
light tan (the ideal color when the
vehicle is ridden normally).
TIP
If the spark plug shows a distinctly
different color, the engine could be
operating improperly. Do not attempt
to diagnose such problems yourself.
Instead, have a Yamaha dealer check
the vehicle.
2. Check the spark plug for electro-
de erosion and excessive carbon
or other deposits, and replace it if
necessary.3. Measure the spark plug gap with
a wire thickness gauge and, if
necessary, adjust the gap to spe-
cification.
1. Spark plug gap
To install the spark plug
1. Clean the surface of the spark
plug gasket and its mating surfa-
ce, and then wipe off any grime
from the spark plug threads.
2. Install the spark plug with the
spark plug wrench, and then
tighten it to the specified torque.
TIP
If a torque wrench is not available
when installing a spark plug, a good
estimate of the correct torque is
1/4–1/2 turn past finger tight. Howe-
ver, the spark plug should be tighte-
ned to the specified torque as soon
as possible.
3. Install the spark plug cap.
Tightening torque:
Spark plug:
12.5 Nm (1.25 m·kgf, 9.0 ft·lbf)
Spark plug gap:
0.7–0.8 mm (0.028–0.031 in)
1
ZAUM0037
Specified spark plug:
NGK/CR7E
PERIODIC MAINTENANCE AND ADJUSTMENT
6-10
6
56P-F8199-E0 30/6/10 09:24 Página 56
