Page 238 of 318
228IN CASE OF AN EMERGENCY
MS41006
To remove the spare tire:
1. Remove the tool tray.
2. Loosen the bolt and remove it.
Then take the spare tire out of the ve-
hicle.
When storing the spare tire, put it in place
with the inner side of the wheel facing up.
Then secure the tire by repeating the
above removal steps in reverse order to
prevent it from flying forward during a
collision or sudden braking.
—Blocking the wheel
MS41001
2. Block the wheel diagonally opposite
the flat tire to keep the vehicle from
rolling when it is jacked up.
When blocking the wheel, place a wheel
block in front of one of the front wheels
or behind one of the rear wheels.
AYGO WE 99E37E11 02.18
Page 241 of 318
IN CASE OF AN EMERGENCY231
—Raising your vehicle
MS41014b
6. After making sure that no one is in
the vehicle, raise it high enough so
that the spare tire can be installed.
Remember you will need more ground
clearance when putting on the spare tire
than when removing the flat tire.
To raise the vehicle, turn the jack handle
clockwise. As the jack touches the vehicle
and begins to lift, double−check that it is
properly positioned.
CAUTION
Never get under the vehicle when the
vehicle is supported by the jack
alone.
—Changing wheels
MS41015a
7. Remove the wheel bolts and change
tires.
Lift the flat tire straight off and put it
aside.
Roll the spare wheel into position and
align the vehicle side holes with the tire
wheel holes. Then secure the wheel with
the bolts.
AYGO WE 99E37E11 02.18
Page 243 of 318

IN CASE OF AN EMERGENCY233
—Lowering your vehicle
MS41018b
9. Lower the vehicle completely and
tighten the wheel bolts.
Turn the jack handle counterclockwise to
lower the vehicle.
Use only the wheel bolt wrench and turn
it clockwise to tighten the bolts. Do not
use other tools or any additional leverage
other than your hands, such as a hammer,
pipe or your foot. Make sure the wrench
is securely engaged over the bolt.
Tighten each bolt a little at a time in the
order shown. Repeat the process until all
the bolts are tight.
CAUTION
DWhen lowering the vehicle, make
sure that all portions of your body
and all other persons around will
not be injured as the vehicle is low-
ered to the ground.
DHave the wheel bolts tightened with
torque wrench to 103 N·m (10.5
kgf·m, 76 ft·lbf), as soon as pos-
sible after changing wheels. Other-
wise, the bolts may loosen and the
wheels may fall off, which could
cause a serious accident.
DTightening the bolts too much could
cause wheel deformation or cracks,
and may result in serious accidents.
DDo not attach a heavily damaged
plastic wheel ornament. It may fly
off the wheel and cause accidents
while the vehicle is moving.
AYGO WE 99E37E11 02.18
Page 245 of 318

IN CASE OF AN EMERGENCY235
—After changing wheels
11. Check the air pressure of the re-
placed tire.
Adjust the air pressure to the specifica-
tions designated on page 299 in Section
8. If the pressure is lower, drive slowly to
the nearest service station and fill to the
correct pressure.
Do not forget to reinstall the tire valve
cap as dirt and moisture could get into
the valve core and possibly cause air
leakage. If the cap is missing, have a new
one put on as soon as possible.
12. Restow all the tools, jack and flat
tire securely.
As soon as possible after changing
wheels, tighten the wheel bolts to the
torque specified on page 299 in Section
8 with a torque wrench. Have a technician
repair the flat tire and replace the spare
tire with it.
CAUTION
Before driving, make sure all the
tools, jack and flat tire are securely
placed in their storage locations to
reduce the possibility of death or se-
rious injury during sudden braking,
sudden swerving or an accident.
PS41515
Aluminium wheels:
Before stowing the flat tire, remove the
center wheel ornament by pushing from
the reverse side.
Be careful not to lose the wheel ornament.
AYGO WE 99E37E11 02.18
Page 248 of 318

238IN CASE OF AN EMERGENCY
MS41003
(c) Towing with sling
type truck
(c) Towing with a sling type truck
NOTICE
Do not tow with a sling type truck,
either from the front or rear. This
may cause body damage.
—Emergency towing
MS41062
If towing is necessary, we recommend
you to have it done by any authorized
Toyota dealer or repairer, or qualified
professional, such as a commercial tow
truck service.
If a towing service is not available in
an emergency, your vehicle may be
temporarily towed by a cable or chain
secured to the right emergency towing
eyelet on the front of the vehicle. Use
extreme caution when towing vehicles.
To install the front towing eyelet, see
“—Installing front towing eyelet” on page
240 in this Section.
NOTICE
Only use the specified towing eyelets;
otherwise your vehicle may be dam-
aged.
A driver must be in the vehicle to steer
it and operate the brakes.
Towing in this manner may be done only
on hard−surfaced roads for short dis-
tances and at low speeds. Also, the
wheels, axles, drive train, steering and
brakes must all be in good condition.
AYGO WE 99E37E11 02.18
Page 249 of 318

IN CASE OF AN EMERGENCY239
CAUTION
DUse extreme caution when towing a
vehicle. Avoid sudden starts or er-
ratic driving maneuvers which
would place excessive stress on the
emergency towing eyelet and towing
cable or chain. The eyelet and tow-
ing cable or chain may break and
cause serious injury or damage.
DIn case of installing the fronteyelet
on the vehicle, be sure to tighten
the front eyelet securely. If the eye-
letisloose,itmaycomeoffwhen
towing and result in death or seri-
ous injury to the passenger in the
front vehicle or damage to that ve-
hicle.
NOTICE
Use only a cable or chain specifically
intended for use in towing vehicles.
Securely fasten the cable or chain to
the towing eyelet provided.
Before towing, release the parking brake
and put the transmission in “N” (multi−
mode manual transmission) or neutral
(manual transmission). The engine switch
must be in “ACC” (engine off) or “ON”
(engine running).
Multi−mode manual transmission only:
After shifting the shift lever to the “N”
position, always make sure that the gear
is actually disengaged and is in neutral by
pushing the vehicle by hand or other
means. In case the gear can not be put
in neutral, turn the engine switch from the
“OFF” to “ON” position, and operate the
shift lever once from “N” to “E” or “R”,
then back to “N” again. Then turn the
engine switch from the “ON” to “OFF”
position. These procedures may help put
the gear in neutral. If the gear still can
not be put in neutral, you can not tow
with cables or chains.
CAUTION
If the engine is not running, the pow-
er assist for the brakes and steering
will not work so steering and braking
will be much harder than usual.
AYGO WE 99E37E11 02.18
Page 251 of 318
IN CASE OF AN EMERGENCY241
MS41063
3. Remove the front towing eyelet cover
on the front bumper, using a flathead
screwdriver which is wrapped with a
cloth.
MS41064
4. Secure the front towing eyelet to the
hole on the bumper by turning clock-
wise.
AYGO WE 99E37E11 02.18
Page 252 of 318

242IN CASE OF AN EMERGENCY
MS41065
5. Tighten the front towing eyelet securely
using a wheel bolt wrench.
CAUTION
When installing theeyelet on the ve-
hicle, be sure to tighten the eyelet
securely. If the eyelet is loose, it may
come off when being towed resulting
in death or serious injury.
MS41053b
In case the shift lever lock is not re-
leased and the shift lever cannot be
moved even though the engine switch
is turned to the “ON” position, follow
the procedures below:
1. Turn the engine switch to the
“LOCK” or “ACC” position. Make
sure the parking brake is applied.
2. To push the link, insert a flathead
screwdriver to the hole. The lever
can be operated while the link is
being pushed.
3. Shift into the “N” position.
4. While fully depressing the brake ped-
al, turn the engine switch “ON”.
5. Check that the gear position indica-
tor lamp indicates “N” or check the
gear position is neutral by the fol-
lowing way:
AYGO WE 99E37E11 02.18
If you cannot shift
multi−mode manual
transmission shift lever