2011 TOYOTA AYGO light

IN CASE OF AN EMERGENCY223
US41023
Jumper cable
Booster
battery
Negative terminal
(“−”mark) Discharged
battery
c. Connect the clamp of the negative
(black) jumper cable to the negative (−)
terminal on the booster battery.
d. Connect the clamp at the other end
of the negative (black) jumper cable to
a solid, stationary, unpainted, metallic
point of the vehicle with the discharged
battery.
The recommended connecting point is
shown in the following illustration:
MS41044b
Connecting point
Do not connect the cable to or near
any part that moves when the engine
is cranked.
CAUTION
When making the connections, to
avoid death or serious injury, do not
lean over the battery or accidentally
let the jumper cables or clamps touch
anything except the correct battery
terminals or the ground.
4.Multi−mode manual transmission:
Turn the engine switch to “ON” posi-
tion. Hold down the brake pedal firmly,
and place the shift lever to “N” posi-
tion. Make sure that the “N” indicator
in the instrument cluster comes on.
Then start your engine in a normal
way.
Manual transmission:Start your en-
gine in the normal way.
After starting, run it at about 2000 rpm
for several minutes with the accelerator
pedal lightly depressed.
5. Carefully disconnect the cables in the
exact reverse order: The negative
cable and then the positive cable.
AYGO WE 99E37E11 02.18

224IN CASE OF AN EMERGENCY
If the cause of the battery discharging is
not apparent (for example lights left on)
you should have it checked at any
authorized Toyota dealer or repairer, or
another duly qualified and equipped
professional.
If the first start attempt is not success-
ful...
Check that the clamp on the jumper
cables are tight. Recharge the discharged
battery with the jumper cables connected
for several minutes and restart your en-
gine in the normal way.
If another attempt is not successful, the
battery may be depleted. Have it checked
at any authorized Toyota dealer or repair-
er, or another duly qualified and equipped
professional.If your engine stalls while driving...
1. Reduce your speed gradually, keeping
a straight line. Move cautiously off the
road to a safe place.
2. Turn on your emergency flashers.
3. Try starting the engine again.
If the engine will not start, see “If your
vehicle will not start” on page 220 in this
Section.
CAUTION
If the engine is not running, the pow-
er assist for the brakes will not work
so braking will be much harder than
usual.
AYGO WE 99E37E11 02.18
If your engine stalls while
driving

IN CASE OF AN EMERGENCY225
If engine speed does not increase when
the accelerator pedal is depressed, there
may be a problem somewhere in the elec-
tronic throttle control system.
At this time, vibration may occur. Howev-
er, if you depress the accelerator pedal
more firmly and slowly, you can drive your
vehicle at low speeds. Have your Toyota
checked by any authorized Toyota dealer
or repairer, or another duly qualified and
equipped professional, as soon as pos-
sible.
Even if the abnormality of the electronic
throttle control system is corrected during
low speed driving, thesystem may not be
recovered until the engine is stopped and
the engine switch is turned to “ACC” or
“LOCK” position.
CAUTION
Be especially careful to prevent erro-
neous pedal operation.
If your high engine coolant temperature
warning light flashes to indicates over-
heating, if you experience a loss of
power, or if you hear a loud knocking
or pinging noise, the engine has prob-
ably overheated. You should follow this
procedure...
1. Pull safely off the road, stop the ve-
hicle and turn on your emergency
flashers. Put the transmission in “N”
(multi−mode manual transmission), or
neutral (manual transmission) and ap-
ply the parking brake. Turn off the air
conditioning if it is being used.
2. If coolant or steam is boiling out of the
radiator or reservoir, stop the engine.
Wait until the steam subsides before
opening the hood. If there is no coolant
boiling over or steam, leave the engine
running and make sure the electric
cooling fan is operating. If it is not,
turn the engine switch off.
CAUTION
To help avoid personal injury, keep
the hood closed until there is no
steam. Escaping steam or coolant is
a sign of very high pressure.
3. Look for obvious coolant leaks from the
radiator, hoses, and under the vehicle.
However, note that water draining from
the air conditioning is normal if it has
been used.
CAUTION
When the engine is running, keep
hands and clothing away from the
moving fan and engine drive belts.
AYGO WE 99E37E11 02.18
If you cannot increase engine
speed (vehicles with multi−mode
manual transmission or vehicle
stability control system)
If your vehicle overheats

248CORROSION PREVENTION AND APPEARANCE CARE
Hand−washing your Toyota
Work in the shade and wait until the
vehicle body is not warm to the touch.
CAUTION
DWhen cleaning under floor or chas-
sis, be careful not to injure your
hands.
DExhaust gasses cause the exhaust
pipe to become quite hot. When
washing the vehicle, be careful not
to touch the pipe until it has cooled
sufficiently, as touching a hot ex-
haust pipe can cause burns.
1. Rinse off loose dirt with a hose. Re-
move any mud or road salt from the
underside of the vehicle or the wheel
wells.
2. Wash with a mild car−wash soap,
mixed according to the manufacturer ’s
instructions. Use a soft cotton mitt and
keep it wet by dipping it frequently into
the wash water. Do not rub hard—let
the soap and water remove the dirt.
Plastic wheel ornaments: The plastic
wheel ornaments are damaged easily by
organic substances. If any organic sub-
stance splash an ornament, be sure to
wash them off with water and check if the
ornament is damaged.
Aluminum wheels: Remove any dirt imme-
diately by using a neutral detergent.
Do not use hard brushes or abrasive
cleaners. Do not use strong or harsh
chemical cleaners. Use the same mild de-
tergent and wax as used on the paint.
Do not use detergent on the wheels when
they are hot, for example after driving for
long distance in the hot weather.
Wash detergent from the wheels immedi-
ately after use.
NOTICE
zDo not use corrosive chemical−
based cleaners on your wheels. (Ex-
ample: hydrofluoric acid)
zDo not use steam cleaners or the
chemicals therein to clean your
wheels.
zDo not use scouring pads, wire
brushes, or coarse abrasives to
clean your wheels.
Plastic bumpers: Wash carefully. Do not
scrub with abrasive cleaners. The bumper
faces are soft.
Exterior lights: Wash carefully. Do not use
organic substances or scrub them with a
hard brush. This may damage the sur-
faces of the lights.
Road tar: Remove with turpentine or
cleaners that are marked safe for painted
surfaces.
3. Rinse thoroughly—dried soap can
cause streaking. In hot weather you
may need to rinse each Section right
after you wash it.
4. To prevent water spots, dry the vehicle
using a clean soft cotton towel. Do not
rub or press hard—you might scratch
the paint.
NOTICE
zDo not use organic substances
(gasoline, kerosene, benzine or
strong solvents), which may be tox-
ic or cause damage.
zDo not scrub any part of the ve-
hicle with a hard brush, which may
cause damage.
AYGO WE 99E37E11 02.18

CORROSION PREVENTION AND APPEARANCE CARE249
Automatic car wash
Your vehicle may be washed in an auto-
matic car wash, but remember that the
paint could be scratched by some types
of brushes, unfiltered washing water, or
the washing process itself. Scratching re-
duces paint durability and gloss, especially
on darker colors. The manager of the car
wash should be able to advise you wheth-
er the process is safe for the paint on
your vehicle.
NOTICE
To prevent damage to the antenna, be
sure to remove it before driving your
Toyota through an automatic car
wash.
To remove the antenna, carefully turn it
counterclockwise.
Waxing your Toyota
Polishing and waxing is recommended
to maintain the original beauty of your
Toyota’s finish.
Apply wax once a month or if the vehicle
surface does not repel water well.
1. Always wash and dry the vehicle be-
fore you begin waxing, even if you are
using a combined cleaner and wax.
2. Use a good quality polish and wax. If
the finish has become extremely weath-
ered, use a car−cleaning polish, fol-
lowed by a separate wax. Carefully fol-
low the manufacturer ’s instructions and
precautions. Be sure to polish and wax
the chrome trim as well as the paint.
NOTICE
If a nozzle becomes blocked, do not
try to clear it with a pin or other
object. The nozzle will be damaged.
Exterior lights: Do not apply wax on the
surfaces of the lights. Wax may cause
damage to the lenses. If you accidentally
put wax on the light surfaces, wipe or
wash it off.
3. Wax the vehicle again when water
does not bead but remains on the sur-
face in large patches.
To u c h−up paint
To u c h−up paint may be used to cover
small chips or scratches.
Apply the paint soon after the damage
occurs or corrosion may set in. To do a
good job, use a small artist’s brush and
stir the paint well. Make sure the area is
clean and dry. To apply the touch−up paint
so it is hardly noticeable, the trick is to
apply it only to the bare spots. Apply only
the smallest amount possible and do not
paint the surface around the scratch or
chip.
AYGO WE 99E37E11 02.18

CORROSION PREVENTION AND APPEARANCE CARE251
Seat belts
The seat belts may be cleaned with
mild soap and water or with lukewarm
water.
Use a cloth or sponge. As you are clean-
ing, check the belts for excessive wear,
fraying, or cuts.
NOTICE
zDo not use dye or bleach on the
belts—it may weaken them.
zDo not use the belts until they be-
come dry.
Windows
NOTICE
zDo not use glass cleaner to clean
the inside of the rear window, as
this may cause damage to the rear
window defogger heater wires. Use
a cloth dampened with lukewarm
water to gently wipe the window
clean. Wipe the window in strokes
running parallel to the heater wires.
zWhen cleaning the inside of the
rear window, be careful not to
scratch or damage the heater wires.
Air conditioning control panel, audio
panel, instrument panel, console panel,
door switch panels and switches
Use a soft damp cloth for cleaning.
Soak a clean soft cloth in cold or luke-
warm water then lightly wipe off any dirt.
NOTICE
zDo not use organic substances (sol-
vents, kerosene, alcohol, gasoline,
etc.) or alkaline or acidic solutions.
These chemicals could cause dis-
coloring, staining or peeling of the
surface.
zIf you use cleaners or polishing
agents, make sure their ingredients
do not include the substances men-
tioned above.
zIf you use a liquid car freshener, do
not spill the liquid onto the ve-
hicle’s interior surfaces. It may con-
tain the ingredients mentioned
above. Immediately clean any spill
using the method mentioned above.
Synthetic leather
DRemove loose dirt using a vacuum
cleaner.
DApply a mild soap solution to the syn-
thetic leather using a sponge or soft
cloth.
AYGO WE 99E37E11 02.18

264DO−IT−YOURSELF MAINTENANCE: Engine and Chassis
Checking the engine oil level
MS72006a
Low level Full level
Add oil O.K. Too full
With the engine at operating tempera-
ture and turned off, check the oil level
on the dipstick.
1. To get a correct reading, the vehicle
should be on level ground. After turning
off the engine, wait more than 5 min-
utes for the oil to drain back into the
bottom of the engine.
2. Pull the dipstick out, hold a rag under
the end and wipe it clean.
3. Reinsert the dipstick—push it in as far
as it will go, or the reading will not be
correct.
4. Pull the dipstick out and look at the oil
level while holding a rag under the
end.
CAUTION
Be careful not to touch the hot ex-
haust manifold.
NOTICE
Be careful not to drop engine oil on
the vehicle components.
If the oil level is below or only slightly
above the low level, add engine oil of
the same type as already in the engine.
Remove the oil filler cap and add engine
oil in small quantities at a time, checking
the dipstick. We recommend that you use
a funnel when adding oil.
The approximate quantity of oil needed to
raise the level between low and full on the
dipstick is indicated as follows:
1.5L(1.6 qt.,1.3 Imp. qt.)
For the engine oil capacity, see “Service
specifications” on page 294 in Section 8.
When the level reaches within the correct
range, install the filler cap hand−tight.
NOTICE
zBe careful not to spill engine oil on
the vehicle components.
zAvoid overfilling, or the engine
could be damaged.
zCheck the oil level on the dipstick
once again after adding the oil.
AYGO WE 99E37E1102.18

DO−IT−YOURSELF MAINTENANCE: Engine and Chassis275
Replacing wheels
WHEN TO REPLACE YOUR WHEELS
If you have wheel damage such as
bending, cracks or heavy corrosion, the
wheel should be replaced.
If you fail to replace a damaged wheel,
the tire may slip off the wheel or cause
loss of handling control.
WHEEL SELECTION
When replacing wheels, care should be
taken to ensure that the wheels are re-
placed by ones with the same load ca-
pacity, diameter, rim width, and inset
∗.
Correct replacement wheels are available
at your Toyota dealer or repairer, or
another duly qualified and equipped pro-
fessional.
∗: Conventionally referred to as “offset”.
A wheel of a different size or type may
adversely affect handling, wheel and bear-
ing life, brake cooling, speedometer/odom-
eter calibration, stopping ability, headlight
aim, bumper height, vehicle ground clear-
ance, and tire or snow chain clearance to
the body and chassis.
Replacement with used wheels is not rec-
ommended as they may have been sub-
jected to rough treatment or high mileage
and could fail without warning. Also, bent
wheels which have been straightened may
have structural damage and therefore
should not be used. Never use an inner
tube in a leaking wheel which is designed
for a tubeless tire.
CAUTION
Do not use wheels other than the
manufacturer ’s recommended size, as
this may cause dangerous handling
characteristics resulting in loss of
control. Otherwise, an accident may
occur resulting in death or serious
injuries.
Aluminum wheel precautions
DWhen installing aluminum wheels,
check that the wheel bolts are tight
after driving your vehicle the first1600
km (1000 miles).
DIf you have rotated, repaired, or
changed your tires, check that the
wheel bolts are still tight after driving
1600 km (1000 miles).
DWhen using tire chains, be careful not
to damage the aluminum wheels.
DToyota recommends the use of Toyota
genuine wheel bolts and wrench de-
signed for your aluminum wheels. Oth-
er bolts and wrenches of matching
quality can also be used.
DWhen balancing your wheels, Toyota
recommends the use of Toyota genuine
balance weights. Other balance weights
canalsobeused.
DAs with any wheel, periodically check
your aluminum wheels for damage. If
damaged, replace immediately.
AYGO WE 99E37E1102.18