2011 Seat Alhambra seats

46
Child safety
● Hook the upper retaining strap to the corresponding retaining ring (for
T OP
TETHER) on the back of the backrest on the rear seat ⇒ fig. 28.
● Push the head restraint down as far as it will go. Ensure that it does not
interf
ere with the seatbelt from the upper attachment.
● Tighten the strap so that the top of the child seat rests on the backrest. WARNING
Child seats with lower anchor points and with an upper retaining strap
mus t

be installed in line with the manufacturer's instructions. Failure to
comply could result in severe injuries.
● Always secure just one r
etaining strap from a child seat to a retaining
ring (for TOP TETHER) on backrest on the rear seat in the luggage com-
partment.
● Never secure a child seat to the retaining rings.
● Never secure a child seat to the movable attachment elements for ve-
hicle
s with an attachment element and rail system . 
Integrated child seat Introduction The integrated child seat is only suitable for children in Group 2 (15-25 kg)
and Group 3 (22-36 k
g), ac

cording to the ECE-R 44 regulation.
Additional information and warnings:
● Seat belts ⇒ pag
e 21 WARNING
Child travelling without their seat belt fastened or not secured using a
suit ab

le restraint system may sustain fatal injuries if the airbag is de-
ployed.
● You should always transport all children up to 12 years of age on the
rear se
at.
● Always disable the front passenger airbag if, in exceptional cases,
you hav
e no alternative but to transport a child in a rear-facing child safe-
ty seat on the front passenger seat.
● Children must always be protected with a child restraint system suit-
ed to their height and w
eight.
● Always fasten children's seat belts correctly. WARNING
Children must travel in a child seat appropriate to their weight and
height whi l

e the vehicle is in motion.
● Children must always be protected with a child restraint system suit-
ed to their height and w
eight.
● Children must assume the proper sitting position and be properly bel-
ted in whil
e travelling.
● The shoulder part of the seat belt must lie approximately on the cen-
tre of the shou
lder, never across the neck or the arm.
● The seat belt must lie close to the upper part of the body.
● The lap belt part must lie across the pelvis, not across the stomach,
and alwa
ys fit closely.
● Allow the belt to retract until it fits tightly over the child's seat.
● Never hold children or babies on your lap. 

48
Child safety
Unfolding the integrated child seat Fig. 29 Integrated child
seat
s. lif
t up the cushion. Fig. 30 Integrated child seats. position the head re-
str
aint

over the side head restraint A and fit into place
B .
The integrated child seat can be fitted with a side head restraint. SEAT rec-
ommends u

se of the integrated child seat with the side head restraint fitted
and also that this seat be used only for children above the age of 3. 

50
Child safety
Seat belt guide handle
● Secure the seat belt guide handle to the side head restraint on the win-
dow s ide.
The guide handle is secured by a button.
● Open the upper button on the seat belt guide handle and pass the belt
webb
ing below the side head restraint and through the guide handle.
● Close the button again.
Adjustin
g the belt routing
● Guide the automatic three-point seat belt below the side head restraint.
● Pull the latch plate and slowly place the belt webbing across the child's
ches
t and lap.
● Insert the latch plate into the buckle for the appropriate seat and push it
down unti
l it is securely locked with an audible click.
● Pull the belt to ensure that the latch plate is securely engaged in the
buck
le. WARNING
The seat belt only offers maximum protection from severe or fatal injuries
when it i s

correctly positioned.
● Children must assume the proper sitting position and be properly bel-
ted in whil
e travelling.
● The shoulder belt must be positioned against the middle of the
shoulder
.
● The seat belt must lie flat and fit comfortably.
● Allow the belt to retract until it fits tightly over the child's seat.
● The lap part of the seat belt must lie across the pelvis, never across
the stom
ach.
● Only one child may occupy a child seat. Removing the seat belt
Fig. 33 Integrated
chi
l

d seats. lowering
the cushion.
Lowering the cushion
● Pull the unlock lever ⇒ fig. 33 A on the cushion in the direction of the
arro w 1 .
● Push the cushion down through the cen tr
al area B in the direction of
the arro w 2 until it safely engages
⇒  . The side supports fold away auto-
matic al
ly.
Removing the side head restraint
● Open the seat belt guide handle.
● Guide the seat belt by hand to pull the belt back in more easily and not
damag
e the trim.
● Push the head restraint up as far as it will go.
● Fold the backrest of the rear seat forwards ⇒ page 117.
● R

emove the head restraint along with the side head restraint.
● Remove the head restraint and side head restraint by pulling on it.
● Fitting the head restraint. 

89
Unlocking and locking
Electric windows Introduction Additional information and warnings:
●
SEAT information system ⇒ pag e 62
● C
entral locking and locking system ⇒ page 74WARNING
Careless use of the electric windows can cause serious injury.
● Only operate the electric windows when nobody is in the way.
● Never leave children or disabled people alone in the vehicle if the
doors ar

e to be locked. The windows cannot be opened in case of an
emergency.
● Always take all the keys with you whenever you leave the vehicle. Af-
ter turnin
g off the ignition, the windows can be opened and closed for a
short time using the buttons on the door as long as the driver's door or
passenger side door is not open.
● When transporting children in the rear seats, always deactivate the
rear el
ectric windows with the child safety lock so that they cannot be
opened and closed. Opening and closing the electric windows Fig. 57 In the driver
door: Butt
on

s for front
and rear electric windows
and child safety lock.
Buttons on the driver door
Leg
end for the fig. 57:
For the front electric windows.
For the sliding door electric windows.
To lock the sliding doors and their windows.
Opening and closing the windows Function Necessary operations
Opening: Press button
 .
Closing: Push the button
 .
To stop the one
touc
h f

unction: Press or pull on the corresponding window button.
 Press the button
 for the electronic child safety
lock t

o deactivate the controls for the windows on
the sliding doors and to lock these doors ⇒ page 81.
The button will light up.  1
2
3
Safety First Operating instructions Practical tips Technical Data

90
Unlocking and locking
After turning off the ignition, the windows can be opened and closed for a
short time u
sing the buttons on the door as long as the driver's door or pas-
senger side door is not open. When the key is removed from the ignition
and the driver's door is open, all of the electric windows can be opened or
closed using the corresponding button on the driver's door. After a few sec-
onds, the convenience opening or closing function will begin ⇒ page 90.
Electric windows: functions One-touch opening and closing
The one-touc
h aut

omatic opening and closing is used to open or close the
windows completely. It will not be necessary to hold the button of the corre-
sponding electric window.
For the one-touch closing function: pull up on the button for the window to
the second position.
For the one-touch opening function: Push down the button for the window
to the second position.
To stop the one touch function: Push or pull on the button of the corre-
sponding window.
Restoring one-touch opening and closing
The one-touch opening and closing function is not active after the vehicle
battery has been disconnected or is flat and will have to be reset.
● Close all windows and doors.
● Pull the button of the corresponding window and hold it for one second
in this po
sition.
● Release the button and pull upwards and hold again. The one-touch
function i
s now ready for operation.
The automatic one-touch electric windows can be reinitialised individually
or several at a time. Convenience opening and closing function
The electric w

indows can be opened or closed from outside using the vehi-
cle key:
● Hold in the unlocking for locking button for the vehicle. All windows
which fu
nction electrically will be either opened or closed.
● To interrupt the function, release the locking or unlocking button.
During c
onvenience closing, first the windows and then the sliding sunroof
will be closed.
In the Configuration - convenience menu, there are different settings for oper- ating the windows ⇒ page 62. WARNING
Careless use of the electric windows can cause serious injury.
● Only operate the electric windows when nobody is in the way.
● Never leave children or disabled people alone in the vehicle if the
doors ar

e to be locked. The windows cannot be opened in case of an
emergency.
● Always take all the keys with you whenever you leave the vehicle. Af-
ter turnin
g off the ignition, the windows can be opened and closed for a
short time using the buttons on the door as long as the driver's door or
passenger side door is not open.
● When transporting children in the rear seats, always deactivate the
rear el
ectric windows with the child safety lock so that they cannot be
opened and closed. Note
The one-touch function and roll-back function will not work if there is a mal-
fu nction in the el

ectric windows. Visit a specialist workshop. 

102
Lights and visibility
Headlight range control, instrument and switch lighting Fig. 63 Next to the
st
eerin
g wheel: instru-
ment and switch lighting
control 1 and headlight
ran g

e control 2 .
1 Instrument and switch lighting
When the hea dlights

are switched on, the brightness of the instruments
and switch lighting can be regulated to suit your requirements by turning
the switch ⇒ fig. 63 1 .
2 Headlight range control
The hea dlight

range control 2 is modified according to the value of the
hea dlight

beam and the vehicle load status. This offers the driver optimum
visibility and the headlights do not dazzle oncoming drivers ⇒  .
The hea dlights

can only be adjusted when the dipped beam is switched on.
To reset, turn switch 2 :
Value Vehicle load status
a) – Two front occupants, luggage compartment empty
1 All seats occupied, luggage compartment empty Value Vehicle load status
a) 2 All seats occupied, luggage compartment full. With trailer
and minimum sup
por

t load 3 Driver only, luggage compartment full. With trailer and
max
imum s

upport load a)
If the vehicle load does not correspond to those shown in the table, it is possible to select
intermedi ar

y positions.
Dynamic headlight range control
The control 2 is not mounted in vehicles with dynamic headlight range
contr o

l. The headlight range is automatically adjusted according to the ve-
hicle load status when the headlights are switched on. WARNING
Heavy objects in the vehicle may mean that the headlights dazzle and
dis tr

act other drivers. This could result in serious accident.
● Adjust the light beam to the vehicle load status so that it does not
blind other driver
s. 
Interior and reading lights Button /
Swit c

h Function
 Switches interior lights off.
 Switches interior lights on.


114
Seats and storage compartments
Seats and storage compartments
Seat adjustment
Mec h
anical controls on the front seat Fig. 75 Front left seat
contr
o

ls.
The controls are mirrored for the front right-hand seat.
Mech
anically and electrically adjusted controls can be combined on the
seat. fig. 75 Function Necessary operations
1 Moving the head re-
str
aint

backwards or for-
wards. Pull the lever and move the seat for-
war
d
s. The front seat must be engag-
ed when the lever is released! 2 Adjusting the lumbar
sup
por

t*. Turn the lever. fig. 75 Function Necessary operations
3 Adjusting the backrest
angl
e. Turn the wheel.
4 Adjusting the seat
height. Pull the lever up or push down (sev-
eral
time

s if necessary) from its
home position. 

115
Seats and storage compartments
Electrical controls on the front seat* Fig. 76 Adjusting the
front
l
eft seat forwards or
backwards, the height,
the seat angle and the
front seat backrest. Fig. 77 Adjusting the
lumbar s
up

port.
The controls are mirrored for the front right-hand seat.
Mech
anically and electrically adjusted controls can be combined on the
seat. fig. 76 Press the control in the direction of the arrow:
A 1
Move the seat backwards or forwards.
2
and
3 Raise or lower the seat.
2
or
3 Adjust the seat angle.
B Forwards or
backwar ds. Adjust the backrest angle.
fig. 77 Press the corresponding area of the switch:
1
or
2 Adjust the curve of the lumbar support.
3
or
4 Adjust the height of the lumbar support.
WARNING
Using the front electric seats in a careless or uncontrolled manner may
le a

d to severe injuries.
● The front seats can also be electrically adjusted when the ignition is
switc
hed off. Never leave children or disabled people alone in the vehicle.
● In the event of an emergency, stop electrical adjustment by pressing
any b
utton. CAUTION
So as not the damage the electrical components of the front seats, do not
kneel on the se ats

or apply specific pressure to one point of the seat or
backrest. Note
● It may not be possible to electrically adjust the seat if the vehicle battery
i s

very low.
● Seat adjustment is stopped when the engine is started. Safety First Operating instructions Practical tips Technical Data