2011 RENAULT SCENIC fuel filter

13B-151V4 MR-372-J84-13B000$120.mif
DIESEL INJECTION
Fault finding – Tests13B
DDCR INJECTION
Vdiag No.: 44, 48
TEST 5 Inlet circuit check
Check for air leaking in or out.
Is air leaking in or out? Carry out the necessary repairs
Check the condition of the air filter. Replace the air filter (see MR 364 (Mégane II) or
MR 370 (Scénic II), Mechanical, 12A, Fuel
mixture, Air filter, Removal - Refitting). Is the air filter in order?
Check that the inlet manifold is not obstructed
(clogged).
Is the inlet manifold blocked? Clean the inlet manifold.
Air system in good order.
YES
NO
NO
YES
YES
NO
DDCR_V44_TEST05/DDCR_V48_TEST05

13B-153V4 MR-372-J84-13B000$120.mif
DIESEL INJECTION
Fault finding – Tests13B
DDCR INJECTION
Vdiag No.: 44, 48
TEST 6
CONTINUED
– Switch off the ignition, reconnect the electrical
connections to the four injectors and the low-
pressure actuator.
– Switch on the ignition again, and clear the
injection faults using the diagnostic tool.
– Check if there is no fuel leak in the high pressure
circuit. Run TEST 7 High pressure circuit
sealing check
– Check the conformity of the diesel filter. Run
TEST 9 Diesel filter check.
– Carry out fault finding on the injectors by
checking the return flow volume of the four
injectors, run TEST 8 Injector return flow.
–Is TEST 8 OK?The pump can supply the operating pressure.
Switch off the ignition, reconnect the electrical
connections
to the four injectors and the low pressure actuator.
Switch on the ignition again, and clear the injection
faults using the diagnostic tool.
Check if there is no fuel leak in the high pressure
circuit. Run TEST 7 High pressure circuit sealing
check.
Carry out fault finding on the injectors by checking the
return flow volume of the four injectors, run TEST 8
Injector return flow.
If TEST 8 is correct, the high pressure fuel circuit is
correct.
Replace the faulty injectors
(see MR 364 (Mégane II) or
MR 370 (Scénic II),
Mechanical, 13B, Diesel
injection, Diesel injector:
Removal - Refitting)Replace the high pressure pump (see MR 364 (Mégane II) or MR 370
(Scénic II), Mechanical, 13B, Diesel injection, High pressure pump:
Removal - Refitting).
A
NO
B
YES
NOYES

13B-159V4 MR-372-J84-13B000$120.mif
DIESEL INJECTION
Fault finding – Tests13B
DDCR INJECTION
Vdiag No.: 44, 48
TEST 9 Diesel filter check
Check the conformity of the diesel filter. Replace the filter with an original part (see MR
364 (Mégane II) or MR 370 (Scénic II),
Mechanical, 13A, Fuel supply, Fuel filter:
Removal - Refitting) Is the diesel filter in order?
– Switch off the ignition and analyse the diesel fuel in the diesel filter.
– Disconnect the diesel supply and return hoses from the filter.
– Block the filter inlets and outlets straight away with appropriate plugs.
– Remove the filter from its holder and shake it firmly while holding the caps in place. Tap the edge of the filter
with a screwdriver handle to detach any contamination. Empty the contents of the filter into a glass container by
lifting a protective plug, then loosening and completely removing the bleed screw.
Is there a deposit of black particles at the bottom of the container?
Pass a magnet beneath the container to collect
all the metal particles. Take the magnet away
from the container.Diesel filter in good order.
Do the particles collected, using the magnet,
cover a surface area greater than 1 cm
2?
Replace the entire injection system Diesel filter in good order.
NO
YES
YESNO
YES
YES
DDCR_V44_TEST09/DDCR_V48_TEST09

13B-160V4 MR-372-J84-13B000$120.mif
DIESEL INJECTION
Fault finding – Tests13B
DDCR INJECTION
Vdiag No.: 44, 48
TEST 11 Turbocharger air chain
Check for the air filter
Check the replacement interval of the air filter on the maintenance booklet.
Compare the part numbers of the air filter fitted to the vehicle and that of the air filter recommended by the
manufacturer.
Check the air filter direction of fitting.
Is the air filter fitted to the vehicle correct?
Check the condition of the air filter
Visually inspect the condition of the filtering section of the air
filter.
Is either the air filter or its seal damaged?
Is the air filter fouled (does it contain a lot of impurities)?Replace the air filter (see MR 364
(Mégane II) or 370 (Scénic II),
Mechanical, 12A, Fuel mixture, Air
filter, Removal - Refitting).
Low pressure circuit check
Note:
Depending on the vehicle type, the best visual access will be
either from above or from below.
Visually inspect the condition of the following components:
– fresh air inlet scoop on the front panel of the vehicle,
– air inlet pipe to the air filter,
– air pipe of the filter until the compressor inlet,
– mountings of the air flowmeter.
Is one of these components incorrect (disconnected,
cut, bent, pierced or kinked pipes)?Replace the defective parts (see MR
364 (Mégane II) or 370 (Scénic II),
Mechanical, 12B, Turbocharging).
YESNO
YES
NO
YES
A
NO
DDCR_V44_TEST11/DDCR_V48_TEST11

13B-162V4 MR-372-J84-13B000$120.mif
DIESEL INJECTION
Fault finding – Tests13B
DDCR INJECTION
Vdiag No.: 44, 48
TEST 13 Diesel fuel conformity check
WARNING
– During this operation, it is essential to:
– refrain from smoking or bringing incandescent objects close to the work area,
– guard against petrol splashes caused by the residual pressure in the pipes,
– wear safety goggles with side guards,
– wear leaktight gloves (Nitrile type).
IMPORTANT
– To avoid any corrosion or damage, protect the areas on which fuel is likely to run.
– To prevent impurities from entering the circuit, place protective plugs on all fuel circuit components
exposed to the open air.
Preparations:
Weigh an empty 1300 ml plastic cup (part no. 77 11 171 413) with its cover (part no. 77 11 171 416) using
electronic scales such as those used in body paint workshops (for example: PANDA, part no. 77 11 224 995).
Record the weight of the empty plastic cup.
This type of plastic cup is used to prepare paint.
Take a 1 litre fuel sample from the diesel filter outlet (see MR 364 (Mégane II) or 370 (Scénic II), Mechanical,
19C, Tank, Fuel tank: Draining), using a pneumatic transfer pump (part no. 634-200) and place it in the 1300 ml
plastic cup.
Cover the plastic cup with its cover and let it settle for approximately2 minutes.
Is the fuel cloudy or does it
separate into two parts?Presence of water in diesel fuel, the fuel is not compliant.
Drain the fuel circuit, including the tank (see MR 364 (Mégane) or
370 (Scénic), Mechanical, 19C, Tank, Fuel Tank: Draining).
YES
A
NO
DDCR_V44_TEST13/DDCR_V48_TEST13

13B-182
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V4 MR-372-J84-13B000$140.mif
DIESEL INJECTION
Fault finding – Fault finding charts13B
InjectionDDCR
Vdiag No.: 44, 48
ALP10
CONTINUED
Check the high pressure pump by running
TEST 6 High pressure system check.The vehicle has entered the "Flow capacity
function" program. This function is activated more
easily when: the external temperature is high, the
fuel level in the tank is at 1/4, the vehicle is laden
and if the vehicle speed is high. Is the "Flow capacity function"
programming active (ET563)?
Check the computer:
Check that the computer connectors are
properly locked.
Check the condition of the computer
connections (bent pin, signs of corrosion,
silicone, etc.).
If the connector(s) is faulty and if there is a
repair procedure (see Technical Note 6015A,
Repairing electrical wiring, Wiring:
Precautions for repair), repair the connector,
otherwise replace the wiring.Check the diesel filter.
Has the diesel fuel filter reached its full mileage?
Replace the diesel filter (see MR 364 (Mégane II)
or MR 370 (Scénic II), Mechanical, 13A, Fuel
supply, Fuel filter: Removal - Refitting).
Contact the Techline if the customer complaint is
still present.
Contact the Techline if the customer complaint
is still present.
A
YES
NO
YES

13B-183
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V4 MR-372-J84-13B000$140.mif
DIESEL INJECTION
Fault finding – Fault finding charts13B
InjectionDDCR
Vdiag No.: 44, 48
OCR*: opening cyclic ratio
ALP11 Loss of power
NOTESSpecial note:
Only consult this customer complaint after a full check with the diagnostic tool.
See explanation for flow capacity function in system operation.
In this case, the lack of power is due to insufficient vacuum for the OCR * setpoint given.
Is the "Flow capacity function" programming
active (ET563)?Check the diesel filter.
Is it close to the replacement mileage?
Using the diagnostic tool, check that the injector
codes (C2I) are correctly entered on the identification
screen. If not, configure the correct injector codes
using command SC002 Enter injector codes.Replace the diesel filter (see MR 364
(Mégane II) or MR 370 (Scénic II),
Mechanical, 13A, Fuel supply, Fuel filter:
Removal - Refitting).
Check the air inlet circuit by running TEST 5 Inlet
circuit check.
Is the engine oil level correct? Top up the oil level.
Is the catalytic converter clogged or damaged?Replace the catalytic converter (see MR
364 (Mégane II) or MR 370 (Scénic II),
19B, Exhaust, Catalytic converter:
Removal - Refitting).
YES
NO
NO
YES
NO
YES
YES
A
NO
DDCR_V44_ALP11/DDCR_V48_ALP11

13B-195
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V4 MR-372-J84-13B000$140.mif
DIESEL INJECTION
Fault finding – Fault finding charts13B
InjectionDDCR
Vdiag No.: 44, 48
ALP18 Oil leaks from the turbocharger
NOTESBefore analysing this customer complaint, check that there are no faults, and the
conformity (or otherwise) of the parameters and statuses, using the diagnostic
tool.
If the customer complaint is not eliminated, perform the following checks.
Check the area around the turbocharger
Note:
An oil leak does not correspond always to a fault of the turbocharger, the oil leak can arise from the area around
the turbocharger.
Depending on the vehicle type, the best visual access will be either from above or from below.
1. Do not start the engine.
Check the area around the turbocharger and identify the origin of the leaks.
Clean the oil traces on the turbocharger.
2. start the engine and let it warm up for several minutes.
IMPORTANT
If the air filter was previously removed, refit it before starting the engine (risk of aspirating foreign bodies into the
air inlet circuit).
Accelerate with no load several times, progressively increasing the duration before releasing the accelerator pedal.
Visually inspect the exterior condition of the fuel supply pipes and the turbocharger oil return and the area around it.
Identify the origin of the leaks.
Is an oil leak present at the air compressor inlet or outlet?
AB
YESNO
DDCR_V44_ALP18/DDCR_V48_ALP18