2011 RENAULT SCENIC battery charge

13B-104V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
MAIN STATUSES AND PARAMETERS OF THE COMPUTER:
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
Battery
voltagePR074: Battery
voltage.13 V < PR074 < 14 VIf there is a fault, apply the
fault finding procedure for
the "Charge circuit".
Engine speedPR055: Engine
speed.
Cold: 900 rpm.
Warm: 805 rpm.Indicates the engine's speed of
rotation in rpm.In the event of a fault, apply
the fault finding procedure for
DF005 "Engine speed sensor
circuit".
Accelerator
pedal positionPR030: Accelerator
pedal position.
0%Indicates the position of
the accelerator pedal as a %.
PR030 = 0 %In the event of a fault,
apply the fault finding
procedures for Pedal sensor
circuit gang 1 and gang 2
(DF008 and DF009)
and DF113 Sensor supply
voltage.
Coolant
temperaturePR064: Coolant
temperature.
Warm: 90°CIndicates the coolant
temperature in °C.
Default value: 80°CIn the event of a fault, consult
the interpretation of
parameter PR064 Coolant
temperature.
External air
temperaturePR061: External air
temperature.Gives the external air
temperature in °C. This
parameter is controlled by the
UCH and transmitted to the
injection via the multiplex
network.
Default value: 20°CIn the event of a fault, apply
the fault finding procedure for
this fault described in the
UCH document.
Inlet air
temperaturePR059: Inlet air
temperature.
Cold = PR061
Warm: 30°CIndicates the inlet air
temperature in °C. This signal is
provided by the air temperature/
pressure sensor.
Default value: 20°C.In the event of a fault, refer to
the interpretation of
parameter PR059 Inlet air
temperature.

13B-107V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
STARTING SUB-FUNCTION:
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
+ After ignition
computer feedET001: + After ignition
computer feed.
PRESENTIndicates + after ignition feed to
the computer.
- Present
- AbsentIn the event of a fault, carry
out the fault finding
procedure for DF047
"Computer supply voltage" or
DF015 "Main relay circuit".
StartingET076: Starting.
AUTHORISEDIndicates whether or not
starting has been authorised by
the injection.
AUTHORISED: The injection
authorises starting.
PROHIBITED: The injection
does not authorise starting.If PROHIBITED, carry out
a complete fault finding
procedure on the preheating
system.
EngineET038: Engine.
RUNNINGIndicates the current status of
the engine.
- UNDER + AFTER IGNITION
FEED
- UNDER STARTER
- RUNNING
- SUPPLY MAINTAINED: Supply
maintained during the power
latch phase.
- STALLED: When the engine
has stalled.
- PROTECTED: When a fault has
appeared or when the engine
speed is locked at a certain
value.NONE
Battery
voltagePR074: Battery
voltage.13 V < PR074 < 14 VIf there is a fault, apply
the fault finding procedure for
the "Charge circuit".

13B-108V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
PROTECTION SUB-FUNCTION:
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
Engine
immobiliserET003: Engine
immobiliser.
INACTIVEIndicates the status of the
immobiliser system.
- INACTIVE: The injection
computer has recognised the
immobiliser code transmitted by
the UCH.
- ACTIVE: The injection computer
has not recognised the
immobiliser code transmitted by
the UCH.If ACTIVE, apply
the associated Help given in
the tool.
Code
programmedET006: Code
programmed
YESIndicates whether the
immobiliser code has been
programmed into the computer.
- YES: Code is programmed.
- NO: Code was not programmed
into the injection computer.If NO, contact the Techline.
Battery
voltagePR074: Battery
voltage.13 V < PR074 < 14 VIf there is a fault, apply
the fault finding procedure for
the "Charge circuit".

13B-115V4 MR-372-J84-13B000$070.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DDCR INJECTION
Vdiag No.: 44, 48
PRE-HEATING/IGNITION SUB-FUNCTION:
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as examples.
Application conditions: Engine off, ignition on.
FunctionParameter or Status
Check or actionDisplay and notes Fault finding
Coolant
temperaturePR064: Coolant
temperature.
Warm: 90°CIndicates the coolant temperature
in °C.
Default value: 80°CIn the event of a fault,
consult the
interpretation of
parameter PR064
Coolant temperature.
External air
temperaturePR061: External air
temperature.Gives the external air temperature
in °C. This parameter is controlled
by the UCH and transmitted to the
injection via the multiplex network.
Default value: 20°CIn the event of a fault,
apply the fault finding
procedure for this fault
described in the UCH
document.
Inlet air
temperature
(invalid for
K9K 728)PR059: Inlet air
temperature.
Cold = PR061
Warm: 30°CIndicates the inlet air temperature
in °C. This signal is provided by the
air temperature/pressure sensor.
Default value: 30°C.In the event of a fault,
refer to the
interpretation of
parameter PR059 Inlet
air temperature.
Battery voltage PR074: Battery voltage.12 V < PR074 < 14 VIf there is a fault, apply
the fault finding
procedure for the
"Charge circuit".

13B-149V4 MR-372-J84-13B000$120.mif
DIESEL INJECTION
Fault finding – Tests13B
DDCR INJECTION
Vdiag No.: 44, 48
TEST 2 Electrical circuit check
Check the battery charge and that the alternator is
operating correctly (see 87G, Engine compartment
connection unit for Mégane II or Scénic II).
Is the charging circuit in good order? Carry out the necessary repairs
Check the fuses.
Are the fuses correct? Carry out the necessary repairs
Check that the injection locking relay is operating
correctly.
Is the injection locking relay working properly? Carry out the necessary repairs
Check the engine earths.
Are the engine earths correct?Carry out the necessary repairs
The electrical circuit is in good order.
NO
YES
NO
YES
NO
YES
NO
YES
DDCR_V44_TEST02/DDCR_V48_TEST02