2011 RENAULT SCENIC engine

13B-49
MR-372-J84-13B050$390.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of faults
Siemens Injection
SID301 and 304
Vdiag No. 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
DF016
PRESENT
OR
STORED
EGR VALVE CONTROL CIRCUIT
CC.0 : Short circuit to earth
CC.1 : Short circuit to + 12 V
CC : Short circuit
CO : Open circuit
1. DEF: Values outside limits
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present with the engine at idle speed.
Special notes:
EGR cut off.
If the fault is present:
– engine instability, possibly even stalling,
– engine starting is difficult or even impossible when cold,
– the OBD warning light is on.
Use the Wiring Diagram Technical Notes for CLIO III, MODUS, MEGANE II ph2,
SCENIC II ph2 and KANGOO II.
Check the connection and condition of the EGR valve connector, component code 1460 and check the connector
for the injection computer, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check for the presence of the supply: 13 V < X <14 V (engine running), 11.5 V < X < 12.5 V (ignition on,
engine stopped) on connection 3VP of component 1460.
Check for earth on connection3VQ of component1460.
Check the continuity, insulation and the absence of interference resistance on the following connections:
–3VP between components 1460 and 120,
–3VQ between components 1460 and 120.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Measure the resistance of the EGR valve, component code 1460:
– with the engine stopped, the EGR valve will be closed (unless there is a fault),
– wait for the ambient temperature to stabilise (approximately 20 ºC) around the valve,
– measure the resistance between connections3VP and 3VQ of component1460.
If the resistance is not between 0.5 Ω < X < 50 Ω, replace the EGR valve (see MR 392 (CLIO III), 385 (MODUS),
364 (MEGANE II), 370 (SCENIC II), 417 (KANGOO II), Mechanical, 14A, Emission control, Exhaust gas
recirculation solenoid valve: Removal - Refitting
).
Use the command RZ002 EGR Adaptive to reinitialise the offsets of the EGR valve (see Replacement of
components).
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_DF016 / SID304_V45_DF016 / SID301_V48_DF016 / SID304_V49_DF016 / SID304_V4D_DF016 / SID301_V4C_DF016

13B-50
MR-372-J84-13B050$390.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of faults
Siemens Injection
SID301 and 304
Vdiag No. 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
DF017
PRESENT
OR
STOREDPRE-POSTHEATING UNIT CONTROL CIRCUIT
CC.0 : Short circuit to earth
CC.1 : Short circuit to + 12 V
CO : Open circuit
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after attempts have been made to start the engine.
Special notes:
If the fault is present, it will be difficult or impossible to start the vehicle when cold, or
preheating will be continuous with damage to the heater plugs.
Use CLIO III, MODUS, MEGANE II ph2, SCENIC II ph2 and KANGOO II Wiring
diagrams Technical Note.
Check the connection and condition of the connector for the preheating unit, component code257 or 980 (see
MR 392, 385, 364, 370 and 417, Mechanical, 13C, Preheating, Pre-post heating unit:
Removal - Refitting), the supply cables for the heater plugs (see MR 392, 385, 364, 370 and 417,
Mechanical, 13C, Preheating, Heater plugs: Removal - Refitting) and the injection computer connector,
component code120 (see MR 392, 385, 364, 370 and 417, Mechanical, 13B, Diesel injection, Diesel injection
computer: Removal - Refitting).
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair) repair the connector(s); otherwise, replace the wiring.
Check the condition of the power supply fuseF2 (70A) on the power supply fuse board component code777.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–3FF between components257 or 980 and 120,
–3FY between components257 or 980 and 120,
–BP35 between components257 or 980 and 777.
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If these connections are correct, replace the preheating unit (see MR 392, 385, 364, 370 and 417, Mechanical,
13C, Preheating, Pre-post heating unit: Removal - Refitting).
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_DF017 / SID304_V45_DF017 / SID301_V48_DF017 / SID304_V49_DF017 / SID304_V4D_DF017 / SID301_V4C_DF017

13B-51
MR-372-J84-13B050$390.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of faults
Siemens Injection
SID301 and 304
Vdiag No. 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
DF025
PRESENT
OR
STOREDPRE-POSTHEATING UNIT DIAGNOSTIC LINE
CC.0 : Short circuit to earth
C0.1 : Open circuit or short circuit to + 12 V
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after several attempts have been made to start the
engine.
Special notes:
If the fault is present, it will be difficult or impossible to start the vehicle when cold, or
preheating will be continuous with damage to the heater plugs.
Use CLIO III, MODUS, MEGANE II ph2, SCENIC II ph2 and KANGOO II Wiring
diagrams Technical Note.
Check the connection and condition of the connector for the preheating unit, component code257 or 980 (see
MR 392, 385, 364, 370 and 417, Mechanical, 13C, Preheating, Pre-post heating unit: Removal - Refitting)
and the supply cables for the heater plugs, component code257 (see MR 392, 385, 364, 370 and 417,
Mechanical, 13C, Pre-heating, Heater plugs: Removal - Refitting).
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair) repair the connector(s); otherwise, replace the wiring.
Check the connection and condition of the connectors for the heater plugs, component codes680, 681, 682 and
683 (see MR 392, 385, 364, 370 and 417, Mechanical, 13C, Pre-heating, Heater plugs: Removal - Refitting)
and the injection computer connector, component code120 (see MR 392, 385, 364, 370 and 417, Mechanical,
13B, Diesel injection, Diesel injection computer: Removal - Refitting).
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair) repair the connector(s); otherwise, replace the wiring.
Measure the resistance of the heater plugs, component codes680, 681, 682 and 683.
If the resistance is not 0.6Ω at +20°C, replace the plug(s) (see MR 392, 385, 364, 370 and 417, Mechanical,
13C, Pre-heating, Heater plugs: Removal - Refitting).
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_DF025 / SID304_V45_DF025 / SID301_V48_DF025 / SID304_V49_DF025 / SID304_V4D_DF025 / SID301_V4C_DF025

13B-53
MR-372-J84-13B050$390.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of faults
Siemens Injection
SID301 and 304
Vdiag No. 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
DF026
PRESENT
OR
STOREDCYLINDER 1 INJECTOR CONTROL CIRCUIT
CC : Short circuit
CO : Open circuit
1. DEF: Line in open circuit
2. DEF: Open circuit or internal electronic fault
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after a road test.
If the fault is present:
– Engine speed and torque are restricted.
–The level 1 warning light is lit.
–The OBD warning light is illuminated.
– Loss of performance, operation on minimum of 2 cylinders.
Use CLIO III, MODUS, MEGANE II ph2, SCENIC II ph2 and KANGOO II Wiring
diagrams Technical Note.
Check the connection and condition of the connector for injector no. 1, component code193 (see MR 392, 385,
364, 370 and 417, Mechanical, 13B, Diesel injection, Diesel fuel injector: Removal - Refitting) and the
injection computer connector, component code120 (see MR 392, 385, 364, 370 and 417, Mechanical, 13B,
Diesel injection, Diesel injection computer: Removal - Refitting).
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair) repair the connector(s); otherwise, replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–3KW between components 193 and 120,
–3CR between components 193 and 120.
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Measure at ambient temperature (approx. 20°C), allow the engine to cool down for at least 30 minutes.
Measure the resistance between connections 3KW and 3CR for injector 1, component code 193.
If the resistance is not between 150 kΩ and 250 kΩ, replace injector 1 (see MR 392, 385, 364, 370 and 417,
Mechanical, 13B, Diesel injection, Diesel injector: Removal - Refitting).
Apply test 7 Incorrect injection quantity.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_DF026 / SID304_V45_DF026 / SID301_V48_DF026 / SID304_V49_DF026 / SID304_V4D_DF026 / SID301_V4C_DF026

13B-54
MR-372-J84-13B050$390.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of faults
Siemens Injection
SID301 and 304
Vdiag No. 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
DF027
PRESENT
OR
STOREDCYLINDER 2 INJECTOR CONTROL CIRCUIT
CC : Short circuit.
CO : Open circuit.
1. DEF: Line in open circuit.
2. DEF: Open circuit or internal electronic fault
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after a road test.
If the fault is present:
– Engine speed and torque are restricted,
–The level 1 warning light will be lit,
–The OBD warning light is lit,
– Loss of performance, operation on minimum of 2 cylinders.
Use CLIO III, MODUS, MEGANE II ph2, SCENIC II ph2 and KANGOO II Wiring
diagrams Technical Note.
Check the connection and condition of the connector for injector no. 2, component code194 (see MR 392, 385,
364, 370 and 417, Mechanical, 13B, Diesel injection, Diesel injector: Removal - Refitting) and the injection
computer connector, component code120 (see MR 392, 385, 364, 370 and 417, Mechanical, 13B, Diesel
injection, Diesel injection computer: Removal - Refitting).
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair) repair the connector(s); otherwise, replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–3KX between components 194 and 120,
–3CS between components 194 and 120.
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Measure at ambient temperature (approx. 20°C), allow the engine to cool down for at least 30 minutes.
Measure the resistance between connections3KX and 3CS for injector 2, component code194.
If the resistance is not between 150 kΩ and 250 kΩ, replace injector 2 (see MR 392, 385, 364, 370 and 417,
Mechanical, 13B, Diesel injection, Diesel injector: Removal - Refitting).
Apply test 7 Incorrect injection quantity.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_DF027 / SID304_V45_DF027 / SID301_V48_DF027 / SID304_V49_DF027 / SID304_V4D_DF027 / SID301_V4C_DF027

13B-55
MR-372-J84-13B050$390.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of faults
Siemens Injection
SID301 and 304
Vdiag No. 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
DF028
PRESENT
OR
STOREDCYLINDER 3 INJECTOR CONTROL CIRCUIT
CC : Short circuit
CO : Open circuit
1. DEF: Line in open circuit
2. DEF: Open circuit or internal electronic fault
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is present with the engine idling.
If the fault is present:
– Engine speed and torque are restricted,
–The level 1 warning light will be lit,
–The OBD warning light is lit,
– Loss of performance, operation on minimum of 2 cylinders.
Use CLIO III, MODUS, MEGANE II ph2, SCENIC II ph2 and KANGOO II Wiring
diagrams Technical Note.
Check the connection and condition of the connector for injector no. 3, component code195 (see MR 392, 385,
364, 370 and 417, Mechanical, 13B, Diesel injection, Diesel injector: Removal - Refitting) and the injection
computer connector, component code120 (see MR 392, 385, 364, 370 and 417, Mechanical, 13B, Diesel
injection, Diesel injection computer: Removal - Refitting).
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair) repair the connector(s); otherwise, replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–3KY between components 195 and 120,
–3CT between components 195 and 120.
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Measure at ambient temperature (approx. 20°C), allow the engine to cool down for at least 30 minutes.
Measure the resistance between connections3KY and 3CT for injector 3, component code195.
If the resistance is not between 150 kΩ and 250 kΩ, replace injector 3 (see MR 392, 385, 364, 370 and 417,
Mechanical, 13B, Diesel injection, Diesel injector: Removal - Refitting).
Apply test 7 Incorrect injection quantity.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_DF028 / SID304_V45_DF028 / SID301_V48_DF028 / SID304_V49_DF028 / SID304_V4D_DF028 / SID301_V4C_DF028

13B-56
MR-372-J84-13B050$390.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of faults
Siemens Injection
SID301 and 304
Vdiag No. 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
DF029
PRESENT
OR
STOREDINJECTOR CYLINDER 4 CONTROL CIRCUIT
CC : Short circuit
CO : Open circuit
1. DEF: Line in open circuit
2. DEF: Open circuit or internal electronic fault
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after a road test.
If the fault is present:
– Engine speed and torque are restricted,
–The level 1 warning light will be lit,
–The OBD warning light is lit,
– Loss of performance, operation on minimum of 2 cylinders.
Use CLIO III, MODUS, MEGANE II ph2, SCENIC II ph2 and KANGOO II Wiring
diagrams Technical Note.
Check the connection and condition of the connector for injector no. 4, component code196 (see MR 392, 385,
364, 370 and 417, Mechanical, 13B, Diesel injection, Diesel injector: Removal - Refitting) and the injection
computer connector, component code120 (see MR 392, 385, 364, 370 and 417, Mechanical, 13B, Diesel
injection, Diesel injection computer: Removal - Refitting).
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair) repair the connector(s); otherwise, replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
–3KZ between components 196 and 120,
–3CU between components 196 and 120.
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Measure at ambient temperature (approx. 20°C), allow the engine to cool down for at least 30 minutes.
Measure the resistance between connections3KZ and 3CU for injector 4, component code196.
If the resistance is not between 150 kΩ and 250 kΩ, replace injector 4 (see MR 392, 385, 364, 370 and 417,
Mechanical, 13B, Diesel injection, Diesel injector: Removal - Refitting).
Apply test 7 Incorrect injection quantity.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_DF029 / SID304_V45_DF029 / SID301_V48_DF029 / SID304_V49_DF029 / SID304_V4D_DF029 / SID301_V4C_DF029

13B-57
MR-372-J84-13B050$390.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of faults
Siemens Injection
SID301 and 304
Vdiag No. 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
DF038
PRESENT
OR
STOREDCOMPUTER
1. DEF to 23. DEF: Internal electronic fault
NOTESPriorities when dealing with a number of faults:
If there are a number of faults, deal with the other system faults first.
Conditions for applying the fault finding procedure to a stored fault:
The fault is declared present after one attempt to start the engine, or with the engine
running.
If the fault is present:
The Level 1 or Level 2 warning lights or OBD warning light are lit.
Check the connection and condition of the injection computer connectors, component code 120 (see MR 392,
385, 364, 370 and 417, Mechanical, 13B, Diesel injection, Diesel injection computer: Removal - Refitting).
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair) repair the connector(s); otherwise, replace the wiring.
In the event of 9.DEF, carry out the multiplex network test (see88B, Multiplexing) (possible fault on lines Can H
and Can L between the injection system and the anti-lock braking system).
Also check that there are no faults on the ABS computer (see38C, Anti-lock braking system).
If the fault is still present, do not erase the fault memory and then contact the Techline.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_DF038 / SID304_V45_DF038 / SID301_V48_DF038 / SID304_V49_DF038 / SID304_V4D_DF038 / SID301_V4C_DF029