2011 RENAULT SCENIC air filter

13B-86
MR-372-J84-13B050$429.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of faults
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
DF308
CONTINUED
Carry out Te s t 11: Turbocharger control solenoid valve.
Carry out Test 12: Turbocharger.
Carry out Te s t 8 : Particle filter injector supply circuit check.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
Explain to the customer how the particle filter system works.

13B-87
MR-372-J84-13B050$429.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of faults
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
*diff: differential
*temp: temperatureDF311
PRESENT
OR
STORED
FAILED REGENERATIONS LIMIT EXCEEDED
1. DEF: Signal outside upper limit
NOTESPriorities when dealing with a number of faults:
Deal with faults stored in the computer first.
Conditions for applying the fault finding procedure to a stored fault:
The fault is declared present after:
– the engine is started,
– a road test.
Special notes:
If the fault is present,
– particle filter regenerations when driving are inhibited.
Use the Ele. 1681 bornier for all operations on the engine management computer
connector.
Deal with the interpretation of fault DF308 Clogged particle filter.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_DF311 / SID304_V45_DF311 / SID301_V48_DF311 / SID304_V49_DF311 / SID304_V4D_DF311 / SID301_V4C_DF311

13B-94
MR-372-J84-13B050$429.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of faults
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
DF652
PRESENT
OR
STOREDTURBINE UPSTREAM TEMPERATURE SENSOR CIRCUIT
CC.0 : Short circuit to earth
CO.1 : Open circuit or short circuit to +12 V.
1. DEF: Micro-break
2. DEF: Signal inconsistency
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault becomes present if:
– ignition is on (CC.0),
– following a road test, engine warm (CO.1).
Special notes:
If the fault is present:
– the EGR function is inhibited,
– particle filter regeneration is inhibited,
– the vehicle performance is reduced,
–the level 1 warning light is lit.
IMPORTANT
The turbine upstream temperature sensor only measures temperatures above
100°C.
Use CLIO III, MODUS, MEGANE II ph2, SCENIC II ph2 and Kangoo II Wiring
diagrams Technical Note.
Run command AC029 High pressure circuit sealing check and check PR667 Turbine upstream temperature.
If the turbine upstream temperature is above 120°C, then the sensor is correct, otherwise continue the fault
finding procedure.
Check the connection and condition of the connector of the turbine upstream temperature sensor, component
code 1589 and the injection computer connector, component code 120 (see MR 392, 385, 364, 370 and 417,
Mechanical, 13B, Diesel injection, Diesel injection computer: Removal - Refitting).
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair) repair the connector(s); otherwise, replace the wiring.
Measure the resistance of the turbine upstream temperature sensor, component code 1589 between
connections 3B and 3JQ.
If the resistance is not between 313 KΩ and 436 KΩ at 100°C, replace the turbine upstream temperature
sensor.
With the ignition on, check for + 5 V on connection 3B and earth on connection 3JQ of the turbine upstream
temperature sensor, component code 1589.
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
SID304_V45_DF652 / SID304_V49_DF652 / SID304_V4D_DF652 / SID301_V4C_DF652

13B-101
MR-372-J84-13B050$468.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of faults
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
DF886
PRESENT
OR
STOREDPRESENCE OF WATER IN THE DIESEL FUEL
1. DEF: Water in diesel fuel
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault becomes present after a road test above 24 mph (40 km/h) and the engine
speed above 1000 rpm.
Use CLIO III, MODUS, MEGANE II ph2, SCENIC II ph2 and KANGOO II Wiring
diagrams Technical Note.
Check whether there is any water in the diesel filter; replace the filter if necessary.
Drain the fuel filter.
Check the connection and condition of the connector of the water in diesel fuel sensor, component code 414.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the connection and condition of the injection computer connector, component code 120 (see MR 392,
385, 364, 370 and 417, Mechanical, 13B, Diesel injection, Diesel injection computer: Removal - Refitting).
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance of the water in diesel fuel sensor, component code 414 between connections 3FB and
M.
If the resistance is not:
2140Ω 771Ω 275Ω replace the water in diesel fuel sensor.
With the ignition on, check for + 12 V after ignition on connection 3FB (or AP15 for Kangoo II) and earth on
connection M (MH or MW for Kangoo II) of the water in diesel fuel sensor, component code 414.
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the continuity, insulation and the absence of interference resistance on the following connections:
–3FB (or AP15 for Kangoo II) between components 414 and 120,
–M (MH or MW for Kangoo II) between components 414 and 120,
–3WT between components
414 and 120.
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Replace the water in diesel fuel sensor.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_DF886 / SID304_V45_DF886 / SID301_V48_DF886 / SID304_V49_DF886 / SID304_V4D_DF886 / SID301_V4C_DF886

13B-105
MR-372-J84-13B050$468.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of faults
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
DF953
PRESENT
OR
STOREDPARTICLE FILTER ABSENT
1. DEF: Signal outside lower limit
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault is declared present after the engine is started or following a road test.
Priorities when dealing with a number of faults:
Deal with the following faults first: DF1003 Particle filter differential pressure
sensor circuit.
If the fault is present:
– smoke is emitted,
– the OBD warning light is lit.
Visually check the particle filter.
Check that the particle filter is in good condition.
Check that the exhaust is not broken or damaged.
Apply the interpretation of fault DF1003 Particle filter differential pressure sensor circuit.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_DF953 / SID304_V45_DF953 / SID301_V48_DF953 / SID304_V49_DF953 / SID304_V4D_DF953 / SID301_V4C_DF953

13B-106
MR-372-J84-13B050$468.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of faults
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
DF991
PRESENT
OR
STOREDPARTICLE FILTER INJECTOR CONTROL CIRCUIT
CC.0 : Short circuit to earth
CC.1 : Short circuit to + 12 V
CO : Open circuit
NOTESConditions for applying the fault finding procedure to a stored fault:
– The fault is declared present after the engine is started or following a road test.
– After actuator command AC238 Particle filter injector.
If the fault is present:
CO or CC.1: Injector not actuated,
CC.0: Injector permanently actuated.
–The level 1 and OBD fault warning lights are lit on the instrument panel.
Use CLIO III, MODUS, MEGANE II ph2, SCENIC II ph2 and Kangoo II Wiring
diagrams Technical Note.
Check the connection and condition of the exhaust injection solenoid valve connector, component code 1750.
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the connection and condition of the injection computer connector, component code 120 (see MR 392,
385, 364, 370 and 417, Mechanical, 13B, Diesel injection, Diesel injection computer: Removal - Refitting).
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance of the particle filter injector, component code 1750 between connections 3FB2 (or
3FB3 for Kangoo II) and 3AGR.
If the resistance is not:
5.2 Ω at - 40°C,
7.5 Ω at 20°C,
10.4Ω at 120°C.
Replace the injector.
With the ignition on, check for + 12 V after ignition on connection 3FB2 (or 3FB3 for Kangoo II) of the exhaust
injection solenoid valve, component code 1750.
If the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the continuity, insulation and the absence of interference resistance on the following connections:
–3FB2 (or 3FB3 for Kangoo II) between components 1750 and 120 (or 1337 for Kangoo II),
–3AGR between components 1750 and 120.
If
the connection(s) are faulty and there is a repair method (see Technical Note 6015A, Repairing electrical
wiring, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_DF991 / SID304_V45_DF991 / SID301_V48_DF991 / SID304_V49_DF991 / SID304_V4D_DF991 / SID301_V4C_DF991

13B-107
MR-372-J84-13B050$468.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of faults
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
DF999
PRESENT
OR
STORED
PARTICLE FILTER DOWNSTREAM TEMPERATURE SENSOR
CIRCUIT
CC.0 : Short circuit to earth
CO.1 : Open circuit or short circuit to +12 V.
1. DEF: Micro-breaks
2. DEF: Signal outside lower limit
3. DEF: Signal inconsistency
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault becomes present:
– with the ignition on (for status CC.0),
– after a road test with a warm engine (for status CO. 1).
Special notes:
If the fault is present:
–The level 1 fault warning light is lit on the instrument panel.
IMPORTANT
The particle filter downstream temperature sensor only measures temperatures
above 50°C.
Use CLIO III, MODUS, MEGANE II ph2, SCENIC II ph2 and Kangoo II Wiring
diagrams Technical Note.
Run command AC029 High pressure circuit sealing test and check PR381 Particle filter downstream
temperature.
If the particle filter downstream temperature is above 50°C, then the sensor is correct, otherwise continue the fault
finding procedure.
Check the connection and condition of the connector of the particle filter downstream temperature sensor,
component code 1288 (see MR 392, 385, 364, 370 and 417, Mechanical, 19B, Exhaust, Particle filter
temperature sensors: Removal - Refitting).
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the connection and condition of the injection computer connector, component code 120 (see MR 392,
385, 364, 370 and 417, Mechanical, 13B, Diesel injection, Diesel injection computer: Removal - Refitting).
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Measure the resistance of the particle filter downstream temperature sensor, component code 1288 between
connections 3TG and 3XU.
If the resistance is not:
106170Ω 33550Ω < X < 33570Ω at 100°C,
6886Ω < X < 6906Ω at 200°C,
2565Ω < X < 2585Ω at 300°C,1192Ω at 400°C,
663Ω 277Ω Replace the sensor (see MR 392, 385, 364, 370 and 417, Mechanical, 19B, Exhaust, Particle filter
temperature sensors: Removal - Refitting).
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_DF999 / SID304_V45_DF999 / SID301_V48_DF999 / SID304_V49_DF999 / SID304_V4D_DF999 / SID301_V4C_DF999

13B-109
MR-372-J84-13B050$468.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of faults
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
DF1000
PRESENT
OR
STORED
PARTICLE FILTER UPSTREAM TEMPERATURE SENSOR CIRCUIT
CC.0 : Short circuit to earth
CO.1 : Open circuit or short circuit to +12 V.
1. DEF: Micro-breaks
2. DEF: Signal outside lower limit
3. DEF: Signal inconsistency
NOTESConditions for applying the fault finding procedure to a stored fault:
The fault becomes present:
– with the ignition on (for status CC.0),
– after a road test with a warm engine (for status CO. 1).
Special notes:
If the fault is present:
– particle filter regeneration is inhibited,
– the level 1 warning light is lit,
– the OBD warning light illuminates after three consecutive driving cycles
(starting + 5 seconds + switching off the ignition and waiting 1 minute).
IMPORTANT
The particle filter upstream temperature sensor only measures temperatures
above 50°C.
Use CLIO III, MODUS, MEGANE II ph2, SCENIC II ph2 and Kangoo II Wiring
diagrams Technical Note.
Run command AC029 High pressure circuit sealing test and check PR382 Particle filter upstream
temperature.
If the particle filter upstream temperature is above 50°C, then the sensor is correct, otherwise continue the fault
finding procedure.
Check the connection and condition of the connection of the particle filter upstream temperature sensor,
component code 1287 (see MR 392, 385, 364, 370 and 417, Mechanical, 19B, Exhaust, Particle filter
temperature sensors: Removal - Refitting).
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the connection and condition of the injection computer connector, component code 120 (see MR 392,
385, 364, 370 and 417, Mechanical, 13B, Diesel injection, Diesel injection computer: Removal - Refitting).
If the connector is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_DF1000 / SID304_V45_DF1000 / SID301_V48_DF1000 / SID304_V49_DF1000 / SID304_V4D_DF1000 / SID301_V4C_DF1000