2011 RENAULT SCENIC wiring

13B-175
MR-372-J84-13B050$624.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of statuses
Siemens Injection
SID304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
ET673
CONTINUED
Use the universal bornier to check the insulation and continuity of the following connections:
– Connection code3LT between components120 and 921,
– Connection code 3LR between components120 and 921,
– Connection code3LS between components120 and 921,
– Connection code3LU between components120 and 921,
– Connection code3LV between components120 and 921,
– Connection code3LW between components120 and 921,
– Connection code5A between components120 and 160.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Carry out a multiplex network test.
Carry out complete fault finding on the UCH (see87B, Passenger Compartment Connection Unit).
Erase the fault memory using the command RZ001 Fault memory.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-177
MR-372-J84-13B050$624.mif
V17
13B
DIESEL INJECTION
Fault finding – Interpretation of statuses
ET703
CRUISE CONTROL/SPEED LIMITER BUTTONS
STATUS DEFINITIONINACTIVE: This status indicates that no button has been pressed.
INCREASE: This status indicates that the increase button is pressed.
DECREASE: This status indicates that the decrease button is pressed.
SUSPEND: This status indicates that the 0 button is pressed.
RESUME: This status indicates that the R button is pressed.
NOTESSpecial notes:
Only perform these tests if the status does not correspond with the system
programming functions.
Use the Wiring Diagram Technical Note for Mégane II ph2, Scénic II ph2, CLIO III,
MODUS and Kangoo II.
INACTIVE
Status ET703 becomes INACTIVE when the cruise control/speed limiter button is not
pressed. These buttons are located on the steering wheel.
Refer to the airbag technical note for the vehicle for details on removal of the driver's
airbag and carrying out the checks in complete safety (see 88C, Airbag and
pretensioners).
If status ET703 does not display INACTIVE,
●check the condition of the cruise control/speed limiter +/- button and the
condition of its connector.
●check the condition of the cruise control/speed limiter "R/0" button and the
condition of its connector,
If the connectors are faulty and if there is a repair procedure (see Te c h n i c a l N o t e
6015A, Electrical wiring repair, Wiring: Precautions for repair), repair the
connector(s), otherwise replace the wiring.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
SID301_V44_ET703/SID304_V45_ET703/SID301_V48_ET703/SID304_V49_ET703/SID304_V4D_ET703/SID301_V4C_ET703
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B2

13B-178
MR-372-J84-13B050$624.mif
V17
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B2DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET703
CONTINUED 1
INCREASE
Status ET703 becomes INCREASE when the cruise control/speed limiter + button is
pressed. This button is on the steering wheel, on the left-hand side.
Refer to the airbag technical note for the vehicle for details on removal of the driver's
airbag and carrying out the checks in complete safety (see 88C, Airbag and
pretensioners).
If status ET703 does not display INCREASE, check the status of the cruise control/
speed limiter +/- button, and the condition of its connector.
If the connector is faulty and if there is a repair method (see Technical Note 6015A,
Repairing electrical wiring, wiring: Precautions for repair), repair the connector(s);
otherwise replace the wiring.
Measure the resistance on the following connections while pressing the + button
(on the button tracks):
●Connection code86G of component 331.
●Connection code 86M of component 331.
If the resistance is not approximately 300Ω, check the continuity of the connection for
the button when the button is in the rest position.
If there is continuity, replace the +/- control button (see MR 392, 385, 364, 370 and 417
Mechanical, 83D, Cruise control, Switch on the steering wheel: Removal -
Refitting).
If the connection or connections are faulty and there is a repair procedure
(seeTechnical Note 6015A, Electrical wiring repair, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-179
MR-372-J84-13B050$624.mif
V17
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B2DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET703
CONTINUED 2
DECREASE
Status ET703 becomes DECREASE when the cruise control/speed limiter button is
pressed. This button is on the steering wheel, on the left-hand side.
Refer to the airbag technical note for the vehicle for details on removal of the driver's
airbag and carrying out the checks in complete safety (see 88C, Airbag and
pretensioners).
If status ET703 does not change to DECREASE, check the status of the cruise control/
speed limiter +/- button and check the condition of its connector.
If the connector is faulty and if there is a repair method (see Technical Note 6015A,
Repairing electrical wiring, wiring: Precautions for repair), repair the connector(s);
otherwise replace the wiring.
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
Measure the resistance of the following connections while pressing the "-" button
(on the button tracks):
●Connection code86G of component 331.
●Connection code 86M of component 331.
If the resistance is not approximately 100Ω, check the continuity of the button when the
button is in the rest position.
If there is continuity, replace the +/- control button.
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
SUSPENDStatus ET703 becomes SUSPEND when the cruise control/speed limiter "0" button is
pressed. This button is located on the steering wheel, to the right.
Refer to the airbag technical note for the vehicle for details on removal of the driver's
airbag and carrying out the checks in complete safety (see 88C, Airbag and
pretensioners).
If status ET703 does not become SUSPEND, check the status of the cruise control/
speed limiter R/0 button and the condition of its connector.
If the connector is faulty and if there is a repair method (see Technical Note 6015A,
Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace the wiring.
Measure the resistance of the following connections while pressing the 0 button
(on the button tracks):
●Connection code86G of component 331.
●Connection code 86M of component 331.
If the resistance is not approximately 0Ω, replace the R/0 control button.
If there is continuity, replace the R/0 control button.
If the connection or connections are faulty and there is a repair procedure
(seeTechnical Note 6015A, Electrical wiring repair, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-180
MR-372-J84-13B050$624.mif
V17
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B2DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET703
CONTINUED 3
RESUME
Status ET703 becomes RESUME when the cruise control/speed limiter "R" button is
pressed. This button is located on the steering wheel, to the right.
Refer to the airbag technical note for the vehicle for details on removal of the driver's
airbag and carrying out the checks in complete safety (see 88C, Airbag and
pretensioners).
If status ET703 does not change to RESUME, check the status of the cruise control/
speed limiter R/0 button and the condition of its connector.
If the connector is faulty and if there is a repair method (see Technical Note 6015A,
Repairing electrical wiring, wiring: Precautions for repair), repair the connector(s);
otherwise replace the wiring.
If the connector is faulty and if there is a repair method (see Technical Note 6015A,
Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace the wiring. Measure the resistance of the following connections
while pressing the R button (on the button tracks):
●Connection code86G of component 331.
●Connection code 86M of component 331.
If the resistance is not approximately 900 Ω, check the continuity of the connection
when the button is in the rest position.
If there is continuity, replace the R/0 control button.
If the connection or connections are faulty and there is a repair procedure
(seeTechnical Note 6015A, Electrical wiring repair, Wiring: Precautions for
repair), repair the wiring, otherwise replace the wiring.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-181
MR-372-J84-13B050$624.mif
V17
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B2DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET704
ET705
BRAKE SWITCH NO. 1
BRAKE SWITCH NO. 2
STATUS DEFINITIONACTIVE: This status indicates that the brake pedal is depressed.
INACTIVE This status indicates that the brake pedal is released.
NOTESSpecial note:
Only perform these tests if the status does not correspond with the system
programming functions.
Use the Wiring Diagram Technical Note for Mégane II ph2, Scénic II ph2, CLIO III,
MODUS and Kangoo II.
Note:
Statuses ET704 and ET705 should change status at the same time. If they do not, consult the interpretation of
faults DF008 Pedal potentiometer circuit gang 1 and DF009 Pedal potentiometer circuit gang 2.
ACTIVE
If the brake lights are working:
– check the continuity and make sure there is no interference resistance on the
following connection:
Connection code 5A between components 160 and 120, 645 and 119.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise
replace it.
If the brake lights are not operational, check:
– the condition and fitting of the brake switch,
– the condition and conformity of the brake light fuse,
– the conformity of the values in the following table:
Continuity between
connectionsInsulation between
connections
Switch pressed
(Brake pedal released)5A and BPT 65G and SP17
Switch released
(Brake pedal depressed)65G and SP17 5A and BPT
or
INACTIVE
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
SID301_V44_ET704/SID304_V45_ET704/SID301_V48_ET704/SID304_V49_ET704/SID304_V4D_ET704/SID301_V4C_ET704
SID301_V44_ET705/SID304_V45_ET705/SID301_V48_ET705/SID304_V49_ET705/SID304_V4D_ET705/SID301_V4C_ET705

13B-182
MR-372-J84-13B050$624.mif
V17
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B2DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET704
ET705
CONTINUED
INACTIVE
CONTINUED
If the connection or connections are faulty and there is a repair procedure
(seeTechnical Note 6015A, Electrical wiring repair, Wiring: Precautions for
repair), repair the wiring, otherwise replace it.
If the values obtained are not correct, replace the brake switch (see MR 392, 385, 364,
370 and 417 Mechanical, 37A, Mechanical component controls, Brake light
switch: Removal - Refitting).
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-196
MR-372-J84-13B050$702.mif
V17
DIESEL INJECTION
Fault finding – Interpretation of parameters
Siemens Injection
SID301 and 304
Vdiag No.: 44-45-48-49-4D-4C
Program No.: B1 and B2
13B
PR030
ACCELERATOR PEDAL POSITION
PARAMETER
DEFINITIONThis parameter indicates the accelerator pedal position in %.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
There must be no present or stored faults.
Perform this fault finding procedure:
– after finding an inconsistency in the parameter,
– after a customer complaint (e.g. lack of power).
Use CLIO III, MODUS, MEGANE II ph2, SCENIC II ph2 and KANGOO II Wiring
Diagrams Technical Notes.
Conformity check with the engine stopped and the ignition on, or the engine running and the engine
coolant temperature > 80°C
If no pressure is exerted on the pedal PR030 = 0%.
In the event of a fault, refer to the interpretation of fault DF008 Pedal potentiometer circuit gang 1 or
DF009 Pedal potentiometer circuit gang 2.
Sensor electrical conformity
Check the continuity and absence of interference resistance of the following connections:
– connection code3LR,
– connection code3LS,
– connection code3LT,
– connection code3LU,
– connection code3LW,
– connection code3LV,
between components 120 and 921.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
AFTER REPAIRDeal with any faults displayed by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
SID301_V44_PR030/SID304_V45_PR030/SID301_V48_PR030/SID304_V49_PR030/SID304_V4D_PR030/SID301_V4C_PR030