2011 RENAULT SCENIC air filter

13B-342V9 MR-372-J84-13B450$152.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR794
PR795
PR796
PR797
PR798
PR799
PR800
PR801
PR802
PR803REGENERATION FAILURE RECORD NO. 1
REGENERATION FAILURE RECORD NO. 2
REGENERATION FAILURE RECORD NO. 3
REGENERATION FAILURE RECORD NO. 4
REGENERATION FAILURE RECORD NO. 5
REGENERATION FAILURE RECORD NO. 6
REGENERATION FAILURE RECORD NO. 7
REGENERATION FAILURE RECORD NO. 8
REGENERATION FAILURE RECORD NO. 9
REGENERATION FAILURE RECORD NO. 10
PARAMETER
DEFINITIONThese parameters are shown in Km.
NOTESSpecial notes:
For Vdiag48:
These parameters must only be interpreted for DF312 Speed request if it is present
or stored.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature
> 80°C, without electrical consumers
These parameters are used so that the history of the last ten failed regenerations when driving is known.
Each parameter between PR794 and PR803 contains the vehicle mileage when particle filter regeneration fails
when driving. each parameter relates to an engine status. They are recorded simultaneously (for example PR797
Regeneration failure record No. 4 is associated with ET709 Engine status record no. 4).
PR794 to PR803 operate through successive copying (when regeneration fails whilst driving, the value of PR794
is copied to PR795, the value of PR795 is copied to PR796 and so on).
When there are more than ten records, the value of PR803 Regeneration failure record no. 10 is overwritten.
The new mileage is allocated to PR794.
If none of the parameters between PR794 and PR803 is available in the sub-function, this means that no data has
been saved. The parameters appear in the sub-function when they have a value above zero.
EDC16C36_V48_PR794/EDC16C36_V48_PR795/EDC16C36_V48_PR796/EDC16C36_V48_PR797/EDC16C36_V48_PR798/
EDC16C36_V48_PR799/EDC16C36_V48_PR800/EDC16C36_V48_PR801/EDC16C36_V48_PR802/EDC16C36_V48_PR803/
EDC16C36_V50_PR794/EDC16C36_V50_PR795/EDC16C36_V50_PR796/EDC16C36_V50_PR797/EDC16C36_V50_PR798/
EDC16C36_V50_PR799/EDC16C36_V50_PR800/EDC16C36_V50_PR801/EDC16C36_V50_PR802/EDC16C36_V50_PR803/
EDC16C36_V58_PR794/EDC16C36_V58_PR795/EDC16C36_V58_PR796/EDC16C36_V58_PR797/EDC16C36_V58_PR798/
EDC16C36_V58_PR799/EDC16C36_V58_PR800/EDC16C36_V58_PR801/EDC16C36_V58_PR802/EDC16C36_V58_PR803
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 48, 50, 58

13B-343V9 MR-372-J84-13B450$152.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
*reg: regeneration
PR816
PR817
PR818
PR819
PR820
PR821
PR822
PR823
PR824
PR825REGENERATION START RECORD NO. 1
REGENERATION START RECORD NO. 2
REGENERATION START RECORD NO. 3
REGENERATION START RECORD NO. 4
REGENERATION START RECORD NO. 5
REGENERATION START RECORD NO. 6
REGENERATION START RECORD NO. 7
REGENERATION START RECORD NO. 8
REGENERATION START RECORD NO. 9
REGENERATION START RECORD NO. 10
PARAMETER
DEFINITIONThese parameters are shown in Km.
NOTESSpecial notes:
For Vdiag48:
These parameters must only be interpreted using ALP11 Particle filter warning light
comes on too often.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature
> 80°C, without electrical consumers
These parameters are used so that the history of the last ten regeneration starts when driving can be found.
EDC16C36_V48_PR816/EDC16C36_V48_PR817/EDC16C36_V48_PR818/EDC16C36_V48_PR819/EDC16C36_V48_PR820/
EDC16C36_V48_PR821/EDC16C36_V48_PR822/EDC16C36_V48_PR823/EDC16C36_V48_PR824/EDC16C36_V48_PR825/
EDC16C36_V50_PR816/EDC16C36_V50_PR817/EDC16C36_V50_PR818/EDC16C36_V50_PR819/EDC16C36_V50_PR820/
EDC16C36_V50_PR821/EDC16C36_V50_PR822/EDC16C36_V50_PR823/EDC16C36_V50_PR824/EDC16C36_V50_PR825/
EDC16C36_V58_PR816/EDC16C36_V58_PR817/EDC16C36_V58_PR818/EDC16C36_V58_PR819/EDC16C36_V58_PR820/
EDC16C36_V58_PR821/EDC16C36_V58_PR822/EDC16C36_V58_PR823/EDC16C36_V58_PR824/EDC16C36_V58_PR825
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 48, 50, 58

13B-344V9 MR-372-J84-13B450$152.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
*reg: regeneration
PR816
PR817
PR818
PR819
PR820
PR821
PR822
PR823
PR824
PR825
CONTINUED
Each parameter from PR816 to PR825 records the mileage at the start of particle filter regeneration, for which the
request status is recorded by ET742 Stored reg.* request status no. 1 to ET751 Stored reg.* request status
no. 10 (for example PR819 Stored regeneration start no. 4 is associated with ET745 Stored reg. request
status no. 4).
Each time a new regeneration is started when driving, the vehicle mileage is recorded in PR816, as well as its
status in ET742 Stored reg.* request status no. 1.
PR816 to PR825 operate through successive copying (when regeneration starts, the value of PR816 is copied to
PR817, the value of PR817 is copied to PR818 and so on).
When there are more than ten stored items, the value of PR825 Regeneration start record no. 10 is overwritten.
The new mileage is allocated to PR816.
If only the parameter PR816 Regeneration start record no. 1 is available in the sub-function and it has no value,
this indicates that no record was made.
If a record has been made, it will have a value above zero.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16 C36
Program No.: 91
Vdiag No.: 48, 50, 58

13B-350V9 MR-372-J84-13B450$160.mif
13B
EDC16 C36
Program No.: 91
Vdiag No.: 44, 4C, 48,
50, 54, 58
Tool
commandDiagnostic tool title comments
SC001Write saved data See Interpretation of commands.
SC002Enter injector codes See Interpretation of commands.
SC003Save computer data See Interpretation of commands.
SC017Particle filter regeneration See Interpretation of commands.
SC031Operational fault finding of cylinders See Interpretation of commands.
SC035High pressure fuel circuit fault finding See Interpretation of commands.
SC036Reinitialise programming See Interpretation of commands.
RZ001Fault memory See Interpretation of commands.
RZ005Programming See Interpretation of commands.
RZ034Computer memory See Interpretation of commands.
LC009Air conditioning See configuration and programming.
LC056Heating elements See configuration and programming.
LC065Water in diesel fuel sensor See configuration and programming.
LC120Cruise control See configuration and programming.
LC121Speed limiter See configuration and programming.
AC004Turbocharging solenoid valve See Interpretation of commands.
AC011Rail pressure regulator See Interpretation of commands.
AC012Damper valve See Interpretation of commands.
AC037Preheating relay See Interpretation of commands.
AC038Low speed GMV relay See Interpretation of commands.
AC039High speed GMV relay See Interpretation of commands.
AC103EGR by-pass See Interpretation of commands.
AC231Richness ratio sensor heating See Interpretation of commands.
VP010Write VIN See Interpretation of commands.
VP036Fuel supply inhibited See
Interpretation of commands.
VP037Lift fuel supply inhibition See Interpretation of commands.
DIESEL INJECTION
Fault finding – Command summary table

13B-355
AFTER REPAIRRepeat the conformity check in the interpretation of statuses and parameters
V9 MR-372-J84-13B450$170.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
SC017PARTICLE FILTER REGENERATION
NOTESOnly run this command after interpretation of the following faults:
– DF308 Clogged particle filter,
– DF311 Failed regenerations limit exceeded,
– DF312 Speed request.
WARNING
It is essential to observe the health and safety regulations (see MR364 (Megane II ph2), MR370 (Scenic II
ph2), Mechanical, 19B, Exhaust, Particle filter: Cleaning) and observe the following procedure.
SAFETY INSTRUCTIONS TO BE FOLLOWED:
The regeneration causes exhaust fumes and high temperatures.
The vehicle must be outside during regeneration.
If it is not possible to carry out regeneration outside, use an extractor fan that can withstand the very high
regeneration temperatures (400°C at the exhaust outlet).
Perform regeneration on a surface free from fire risks (oil, dry leaves, etc.). Nothing should be left in the vicinity
of the exhaust pipe.
IMPORTANT
– Check the engine oil level before running the command to avoid any engine racing. The oil level must
be between the minimum threshold and the middle level on the oil dipstick.
– Before performing a particle filter regeneration, it is essential to deactivate the air conditioning
compressor (risk of engine damage) and all the electrical consumers.
IF NECESSARY:
Regeneration can be stopped by briefly pressing the vehicle start button twice (less than 3 seconds).
Switch off the ignition and wait for the diagnostic tool message (maximum time 8 minutes) Communication lost
with computer: EDC16C36, check the tool connection and the computer supply. before switching on the
ignition again.
PROCEDURE TO BE FOLLOWED:
Before a particle filter regeneration, check that there are no leaks or blockages in the exhaust pipe,
Repair if necessary
To run this command, select the command mode on the diagnostic tool, and select command SC017 Particle
filter regeneration.
When regeneration is complete, a message will indicate whether regeneration was successful, and what
operations need to be carried out (filter replacement, whether an oil service is required, etc.).
EDC16C36_V48_SC017/EDC16C36_V50_SC017/EDC16C36_V58_SC017EDC16 C36
Program No.: 91
Vdiag No.: 48, 50, 58

13B-356
AFTER REPAIRRepeat the conformity check in the interpretation of statuses and parameters
V9 MR-372-J84-13B450$170.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
SC017
CONTINUED 1
DESCRIPTION OF THE PROCESS
Particle filter regeneration takes place in 3 stages (values given as a guide only):
–Heating phase: the engine speed is fixed or fluctuating around 2000 rpm.
This phase lasts between 8 and 14 minutes, until the coolant temperature exceeds 70°C.
–Regeneration phase: the speed is fixed or varies around 2000 rpm. Engine injection is retarded. The exhaust
fumes rise in temperature and burn the soot retained in the particle filter. Then the combustion of the soot stored
in the particle filter causes the particle filter upstream temperature to increase, possibly reaching 600°C
depending on the amount of soot in the particle filter. This phase lasts 28 minutes.
–Cooling phase: the engine speed decreases to 1250 rpm then increases to 1750 rpm.
Engine injection returns to normal and the exhaust gases cool the particle filter.
This phase lasts 3 minutes.
The procedure lasts at least 40 minutes, and varies depending on the time taken to reach a coolant temperature
of 70°C.
VALIDATING THE REGENERATION PROCESS:
At the end of regeneration, a message appears to announce whether the regeneration was successful:
●Particle filter regeneration finished:
Consult PR1012 Weight of soot after regeneration. If PR1012 is less than 15 g, the particle filter regeneration
completed correctly. If PR1012 is greater than 15 g, a second particle filter regeneration must be performed using
the command in the diagnostic tool and choose command SC017.
EDC16 C36
Program No.: 91
Vdiag No.: 48, 50, 58

13B-357
AFTER REPAIRRepeat the conformity check in the interpretation of statuses and parameters
V9 MR-372-J84-13B450$170.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
SC017
CONTINUED 2
IMPORTANT:
Before performing a second After-Sales regeneration of the particle filter, the engine must be allowed to cool down
for 2 hours with the bonnet open.
Do not carry out the usual engine oil change before a second After-Sales regeneration.
Only for Vdiag 50:
– Change the engine oil if a message on the instrument panel requests it.
For the other VDiag:
–Consult PR848 Number of regeneration failures. If PR848 is greater than 3, change the engine oil.
●Particle filter too full - replace the particle filter: regeneration has failed. The weight of soot in the particle
filter is so great that it is creating back-pressure. Deal with any faults that appear or replace the particle filter.
Run command SC036 Reinitialise programming and select After particle filter replacement.
– Switch off the ignition and wait for the diagnostic tool message (maximum time 8 minutes): Communication
lost with computer: EDC16C36, check the tool connection and computer power supply.
–Then switch on the ignition again, clear the present or stored faults from the computer memory (operation
to be carried out within 3 minutes of switching on the ignition).
– Check the weight of soot: PR383 Weight of soot in the particle filter.
– If PR383
≥ 1 g. Apply the procedure of test 12 Manual clearing of the weight of soot.
Only for Vdiag 50:
– Change the engine oil if a message on the instrument panel requests it.
– For the other Vdiags:
–Consult PR848 Number of regeneration failures. If this parameter is greater than 3, it is essential to change
the engine oil.
– Explain to the customer the procedure for regeneration when driving to avoid unnecessary repairs: see PART D
in the interpretation of DF312 Speed request.
EDC16 C36
Program No.: 91
Vdiag No.: 48, 50, 58

13B-358
AFTER REPAIRRepeat the conformity check in the interpretation of statuses and parameters
V9 MR-372-J84-13B450$170.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
SC017
CONTINUED 3
●Particle filter regeneration failed - run test Temperature upstream of turbine too low: regeneration has
failed because the temperature upstream of the turbine is too low. Run Test 8 Temperature upstream of
turbine too low.
In all cases, carry out the following operations:
– switch off the ignition and wait for the diagnostic tool message (maximum time 8 minutes): Communication
lost with computer: EDC16C36, check the tool connection and the computer supply.
– switch on the ignition and establish dialogue with the injection computer,
– run command SC036 Reinitialise programming,
– depending on the operation performed, select After particle filter regeneration with diagnostic tool, or After
particle filter replacement
– switch off the ignition and wait for the diagnostic tool message (maximum time 8 minutes): Communication
lost with computer: EDC16C36, check the tool connection and the computer supply.
–Then switch on the ignition again, clear the present or stored faults from the computer memory (operation
to be carried out within 3 minutes of switching on the ignition).
– Check the weight of soot: PR383 Weight of soot in the particle filter.
– If PR383
≥ 1 g. Apply test procedure 12 Manual clearing of the weight of soot.
If DF308 Particle filter clogged or DF312 Speed request is still present, contact Techline.
Note:
It is essential to change the engine oil and the oil filter in the following cases:
– following an After-Sales regeneration only if a message on the CLIP diagnostic tool requests it,
– following particle filter replacement,
after a second regeneration (when two successive regenerations).
EDC16 C36
Program No.: 91
Vdiag No.: 48, 50, 58