2011 RENAULT SCENIC air filter

13B-285
MR-372-J84-13B200$684.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
PR784
PR785
PR786
PR787
PR788
PR789
PR790
PR791
PR792
PR793
CONTINUED
These parameters are used so that the history of the last ten regeneration failures when driving are known.
For VDIAG 58, 18, 1C:
Each parameter from PR784 to PR793 records the mileage when the particle filter warning light comes on which
is associated with DF312 Speed request.
Each time the particle filter warning light comes on, the vehicle mileage is stored in the following parameter
(PR+1).
When all ten parameters have a value other than zero and the particle filter warning light is illuminated again, the
mileage information for PR784 is cleared and replaced by the new value.
For VDIAG 5C and 20
Each parameter from PR784 to PR793 contains a record of the vehicle mileage when the particle filter warning
light illuminates. The appearance of fault DF312 Speed request is associated with each of these parameters.
PR784 to PR793 operate through successive feedback (when the particle filter warning light comes on, the value
of PR784 is copied to PR785, the value of PR785 is copied to PR786 and so on).
When there are more than ten records, the value of PR793 is overwritten. The new mileage is allocated to PR784.
If none of the parameters between PR784 and PR793 is available in the sub-function, this means than nothing
has been recorded. The parameters appear in the sub-function when they have a value above zero.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-286
MR-372-J84-13B200$684.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
PR794
PR795
PR796
PR797
PR798
PR799
PR800
PR801
PR802
PR803REGENERATION FAILURE RECORD NO. 1
REGENERATION FAILURE RECORD NO. 2
REGENERATION FAILURE RECORD NO. 3
REGENERATION FAILURE RECORD NO. 4
REGENERATION FAILURE RECORD NO. 5
REGENERATION FAILURE RECORD NO. 6
REGENERATION FAILURE RECORD NO. 7
REGENERATION FAILURE RECORD NO. 8
REGENERATION FAILURE RECORD NO. 9
REGENERATION FAILURE RECORD NO. 10
PARAMETER
DEFINITIONThese parameters are shown in Km.
NOTESSpecial notes:
Interpret these parameters only if DF312 Speed request is present or stored.
Conformity check with the engine stopped and the ignition on, or with the engine running and the engine
coolant temperature > 80°C
These parameters are used so that the history of the last ten regeneration failures when driving are known.
For VDIAG 58, 18, 1C
Each of these parameters contains the vehicle mileage during a failed particle filter regeneration when driving.
Each parameter relates to an engine status. The statuses and parameters are recorded at the same time
(for example PR797 is associated with ET709 Engine status record no. 4).
Each new recorded value is saved under the next PR (PR+1).
When all ten parameters have a value other than zero and there is a regeneration failure when driving, the
mileage information for PR794 is cleared and replaced with the new value.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_PR794/EDC16_V58_PR794/EDC16_V5C_PR794/EDC16_V50_PR795/EDC16_V58_PR795/EDC16_V5C_PR795/
EDC16_V50_PR796/EDC16_V58_PR796/EDC16_V5C_PR796/EDC16_V50_PR797/EDC16_V58_PR797/EDC16_V5C_PR797/
EDC16_V50_PR798/EDC16_V58_PR798/EDC16_V5C_PR798/EDC16_V50_PR799/EDC16_V58_PR799/EDC16_V5C_PR799/
EDC16_V50_PR800/EDC16_V58_PR800/EDC16_V5C_PR800/EDC16_V50_PR801/EDC16_V58_PR801/EDC16_V5C_PR801/
EDC16_V50_PR802/EDC16_V58_PR802/EDC16_V5C_PR802/EDC16_V50_PR803/EDC16_V58_PR803/EDC16_V5C_PR803/
EDC16_V18_PR794/EDC16_V1C_PR794/EDC16_V20_PR794/EDC16_V18_PR795/EDC16_V1C_PR795/EDC16_V20_PR795/
EDC16_V18_PR796/EDC16_V1C_PR796/EDC16_V20_PR796/EDC16_V18_PR797/EDC16_V1C_PR797/EDC16_V20_PR797/
EDC16_V18_PR798/EDC16_V1C_PR798/EDC16_V20_PR798/EDC16_V18_PR799/EDC16_V1C_PR799/EDC16_V20_PR799/
EDC16_V18_PR800/EDC16_V1C_PR800/EDC16_V20_PR800/EDC16_V18_PR801/EDC16_V1C_PR801/EDC16_V20_PR801/
EDC16_V18_PR802/EDC16_V1C_PR802/EDC16_V20_PR802/EDC16_V18_PR803/EDC16_V1C_PR803/EDC16_V20_PR803

13B-287
MR-372-J84-13B200$684.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
PR794
PR795
PR796
PR797
PR798
PR799
PR800
PR801
PR802
PR803
CONTINUED
For VDIAG 5C and 20
Each parameter between PR794 and PR803 contains the vehicle mileage when particle filter regeneration fails
when driving. Each parameter relates to an engine status. They are recorded simultaneously (for example, PR797
is associated with ET709 Engine status record no. 4).
PR795 to PR803 operate through successive feedback (when regeneration fails whilst driving, the value of
PR794 is copied in PR795, the value of PR795 is copied in PR796 and so on).
When there are more than ten records, the value of PR803 is overwritten. The new mileage is allocated to PR794.
If none of parameters PR794 to PR803 is available in the sub-function, this means that no record has been made.
The parameters appear in the sub-function when they have a value above zero.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-288
MR-372-J84-13B200$684.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
* rege: regenerationPR816
PR817
PR818
PR819
PR820
PR821
PR822
PR823
PR824
PR825
REGENERATION START RECORD NO. 1
REGENERATION START RECORD NO. 2
REGENERATION START RECORD NO. 3
REGENERATION START RECORD NO. 4
REGENERATION START RECORD NO. 5
REGENERATION START RECORD NO. 6
REGENERATION START RECORD NO. 7
REGENERATION START RECORD NO. 8
REGENERATION START RECORD NO. 9
REGENERATION START RECORD NO. 10
PARAMETER
DEFINITIONThese parameters are shown in Km.
NOTESSpecial notes:
Interpret these parameters only for ALP9 Particle filter warning light comes on too
often.
Conformity check with the engine stopped and the ignition on, or with the engine running and the engine
coolant temperature > 80°C
These parameters are used so that the history of the last ten activations of the particle filter warning light are
known.
For VDIAG 58, 18 and 1C
Each parameter between PR816 and PR825 contains the vehicle mileage when particle filter regeneration starts
when driving. Each parameter is connected with a "Rege* request status record". They are recorded
simultaneously (for example, PR819 is associated with ET745 Rege* request status record no. 4).
Each new recorded value is saved under the next PR (PR+1).
When all ten parameters have a value other than zero, and a new regeneration starts when driving, the mileage
information for PR816 is cleared and replaced with the new value.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_PR816/EDC16_V58_PR816/EDC16_V5C_PR816/EDC16_V50_PR817/EDC16_V58_PR817/EDC16_V5C_PR817/
EDC16_V50_PR818/EDC16_V58_PR818/EDC16_V5C_PR818/EDC16_V50_PR819/EDC16_V58_PR819/EDC16_V5C_PR819/
EDC16_V50_PR820/EDC16_V58_PR820/EDC16_V5C_PR820/EDC16_V50_PR821/EDC16_V58_PR821/EDC16_V5C_PR821/
EDC16_V50_PR822/EDC16_V58_PR822/EDC16_V5C_PR822/EDC16_V50_PR823/EDC16_V58_PR823/EDC16_V5C_PR823/
EDC16_V50_PR824/EDC16_V58_PR824/EDC16_V5C_PR824/EDC16_V50_PR825/EDC16_V58_PR825/EDC16_V5C_PR825/
EDC16_V18_PR816/EDC16_V1C_PR816/EDC16_V20_PR816/EDC16_V18_PR816/EDC16_V1C_PR817/EDC16_V20_PR817/
EDC16_V18_PR816/EDC16_V1C_PR818/EDC16_V20_PR818/EDC16_V18_PR819/EDC16_V1C_PR819/EDC16_V20_PR819/
EDC16_V18_PR820/EDC16_V1C_PR820/EDC16_V20_PR820/EDC16_V18_PR821/EDC16_V1C_PR821/EDC16_V20_PR821/
EDC16_V18_PR822/EDC16_V1C_PR822/EDC16_V20_PR822/EDC16_V18_PR823/EDC16_V1C_PR823/EDC16_V20_PR823/
EDC16_V18_PR824/EDC16_V1C_PR824/EDC16_V20_PR824/EDC16_V18_PR825/EDC16_V1C_PR825/EDC16_V20_PR825

13B-289
MR-372-J84-13B200$684.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
*rege: regenerationPR816
PR817
PR818
PR819
PR820
PR821
PR822
PR823
PR824
PR825
CONTINUED
For VDIAG 5C and 20
Each parameter from PR816 to PR825 records the mileage when particle filter regeneration starts and the status
of each request is recorded by ET742 Rege* request status record no. 1 to ET751 Rege* request status
record no. 10 (for example, PR819 is associated with ET745 Rege* request status record no.4).
Each time a new regeneration when driving is started, the vehicle mileage is recorded in PR816, as well as its
status in ET742 Rege* request status record no. 1
PR816 to PR825 operate through successive feedback (when regeneration starts, the value of PR816 is copied to
PR817, the value of PR817 is copied to PR818 and so on).
When there are more than ten records, the value of PR825 is overwritten.
The new mileage is allocated to PR816.
If only parameter PR816 is available in the sub-function and it has a value of zero, this means that no record was
made.
If a recording has been made, it will have a value above zero.
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.

13B-290
MR-372-J84-13B200$684.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
PR1012
WEIGHT OF SOOT AFTER REGENERATION
PARAMETER
DEFINITIONThis parameter indicates the weight of soot in g present in the particle filter after
a regeneration.
NOTESThis parameter is to be consulted after using SC017 Particle filter regeneration.
Conformity check with the engine stopped and ignition on, or the engine running and engine coolant
temperature > 80°C, without electrical consumers
If PR1012 is less than 15 g, the particle filter regeneration completed correctly.
If PR1012 is greater than 15 g, a second particle filter regeneration must be performed using command SC017
Particle filter regeneration.
IMPORTANT:
Before performing a second After-Sales regeneration of the particle filter, the engine must be allowed to cool
down for 2 hours with the bonnet open.
Do not perform a routine oil change before a second After-Sales regeneration (see SC017 Particle filter
regeneration).
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
EDC16_V50_PR1012/EDC16_V58_PR1012/EDC16_V5C_PR1012/EDC16_V18_PR1012/EDC16_V1C_PR1012/EDC16_V20_PR1012

13B-291
MR-372-J84-13B200$720.mif
V13
13B
DIESEL INJECTION
Fault finding – Command summary table
Tool command Diagnostic tool title
SC001Write saved data
SC002Enter injector codes
SC003Save computer data
SC017Particle filter regeneration
SC036Reinitialise programming
CF030Thermoplungers
RZ005Programming
RZ007Fault memory
RZ034Computer memory
LC009Air conditioning
LC056Thermoplungers
LC065Water in diesel fuel sensor
LC120Cruise control
LC121Speed limiter
VP010Enter VIN
AC001Preheating unit
AC004Turbocharging solenoid valve
AC011Rail pressure regulator
AC012Damper valve
AC031Thermoplunger no. 3 relay (Vdiag 58 only)
AC038Low-speed fan assembly relay (Vdiag 18, 1C, 20 only)
AC039High-speed fan assembly relay (Vdiag 18, 1C, 20 only)
AC063Thermoplunger no. 1 relay (Vdiag 58 only)
AC064Thermoplunger no. 2 relay (Vdiag 58 only)
AC195Electric coolant pump
MR-372-J84-13B200$720.mif
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C

13B-292
MR-372-J84-13B200$756.mif
V13
13B
DIESEL INJECTION
Fault finding – Interpretation of commands
SC001
WRITE SAVED DATA
NOTESAll data must be saved with command SC003 Save computer data for this command
to be run.
writing is carried out after the computer has been reprogrammed or replaced
Validating this command writes the data saved using command SC003 Save computer data.
The data is as follows:
– vehicle idle speed.
– injector calibration codes (if the vehicle is fitted with ima).
– programming of exhaust gas recirculation valve data.
– options available on the vehicle and managed by the computer (example: air conditioning).
– specific data related to the operation of the particle filter.
they will configure the computer and will enable it to avoid:
– engine malfunction after reprogramming or replacing the computer,
– faulty interpretation of information provided by the clip tool.
EDC16_V50_SC001/EDC16_V58_SC001/EDC16_V5C_SC001/EDC16_V18_SC001/EDC16_V1C_SC001/EDC16_V20_SC001 EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
MR-372-J84-13B200$756.mif