2011 RENAULT SCENIC engine coolant

13B-226
MR-372-J84-13B200$612.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
PR035
ATMOSPHERIC PRESSURE
PARAMETER
DEFINITIONThis parameter indicates the atmospheric pressure in mbar. The sensor is integrated in
the computer.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature
>80 °C.
The default value is: 750 mbar
In the event of a fault, consult the interpretation of DF003 Atmospheric pressure sensor circuit.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_PR035/EDC16_V58_PR035/EDC16_V5C_PR035/EDC16_V18_PR035/EDC16_V1C_PR035/EDC16_V20_PR035

13B-227
MR-372-J84-13B200$612.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
PR037
REFRIGERANT PRESSURE
PARAMETER
DEFINITIONThis parameter indicates the atmospheric pressure in bar. The sensor is integrated in
the computer.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine running, engine coolant temperature > 80°C.
The value must be between (Vdiag 50, 58 and 5C only):
1 bar < PR037 < 27 bar
In the event of a fault, refer to the interpretation of fault DF049 “Refrigerant sensor circuit”.
The value must be between (Vdiag 18, 1C and 20 only):
1 bar < PR037 < 40 bar
In the event of a fault test the multiplex network.
Conformity check with engine stopped and ignition on.
The value must be between (Vdiag 50, 58 and 5C only):
2 bar < PR037 < 27 bar
In the event of a fault, refer to the interpretation of fault DF049 “Refrigerant sensor circuit”.
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
EDC16_V50_PR037/EDC16_V58_PR037/EDC16_V5C_PR037/EDC16_V18_PR037/EDC16_V1C_PR037/EDC16_V20_PR037

13B-228
MR-372-J84-13B200$612.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
PR038
RAIL PRESSURE
PARAMETER
DEFINITIONThis parameter indicates the rail pressure in bar.
NOTESNo faults should be present or stored.
Perform this fault finding procedure:
– after finding an inconsistency in the parameter,
– after a customer complaint (starting faults, poor performance, stalling, etc.).
– after interpretation of command AC225 Rail pressure regulator.
Special notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine stopped and ignition on.
The rail pressure value is between:
0 < PR038 < 10 bar
Default value: 250 bar.
In the event of a fault, consult the interpretation of fault DF007 Rail pressure sensor circuit.
Conformity check with engine running, engine coolant temperature > 80°C.
The rail pressure value is (engine at idle speed):
PR038 = ~ 315 bar
Default value: 250 bar.
In the event of a fault, consult the interpretation of fault DF007 Rail pressure sensor circuit.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_PR038/EDC16_V58_PR038/EDC16_V5C_PR038/EDC16_V18_PR038/EDC16_V1C_PR038/EDC16_V20_PR038

13B-230
MR-372-J84-13B200$612.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
PR041
TURBOCHARGING PRESSURE
PARAMETER
DEFINITIONThis parameter indicates the turbocharging pressure in mbar.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature
>80 °C.
The turbocharging pressure value is:
PR041 = PR035 “Atmospheric pressure” ± 10 mbar
In the event of a fault, apply the interpretation of DF004 Turbocharging pressure sensor circuit.
Sensor electrical conformity.
Check the continuity and absence of interference resistance on the following connections:
For Mégane II and Scénic II:
– connection code 3LQ,
– connection code 3LP,
– connection code 3LN.
Between components 120 and 1071.
For Laguna II:
– connection code 3LQ,
– connection code 3LP,
– connection code 3LN.
Between components 120 and 1474.
If any of the connections are faulty and there is a repair method (see Technical Note 6015A, Electrical wiring
repair, Wiring: precautions for repairs), repair the wiring; otherwise replace the wiring.
AFTER REPAIRCarry out a road test followed by a check with the diagnostic tool.
EDC16_V50_PR041/EDC16_V58_PR041/EDC16_V5C_PR041/EDC16_V18_PR041/EDC16_V1C_PR041/EDC16_V20_PR041

13B-232
MR-372-J84-13B200$612.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
*OCR: * Opening Cycle RatioPR047
TURBO PRESSURE OCR*
PARAMETER
DEFINITIONThis parameter indicates the turbocharger pressure opening cyclic ratio in %.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Engine running, engine coolant temperature > 80°C.
The value must be between 60% < PR047 < 90%.
The Opening Cyclic Ratio should be identical to the correction of the solenoid valve position
Conformity check with engine stopped and ignition on.
This value must be PR047 < 5%.
The Opening Cyclic Ratio should be identical to the correction of the solenoid valve position
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_PR047/EDC16_V58_PR047/EDC16_V5C_PR047/EDC16_V18_PR047/EDC16_V1C_PR047/EDC16_V20_PR047

13B-233
MR-372-J84-13B200$612.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
*OCR: Opening cyclic ratioPR048
RAIL PRESSURE REGULATION VALVE OCR*
PARAMETER
DEFINITIONThis parameter indicates the turbocharger pressure opening cyclic ratio in %.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Engine running, engine coolant temperature > 80°C.
The value must be between 35% < PR048 < 45%
In the event of a fault, consult the interpretation of fault DF007 Rail pressure sensor circuit.
Engine stopped, ignition on.
The value must be PR048 = 15%.
In the event of a fault, consult the interpretation of faults DF007 Rail pressure sensor circuit and DF053 Rail
pressure regulation function.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_PR048/EDC16_V58_PR048/EDC16_V5C_PR048/EDC16_V18_PR048/EDC16_V1C_PR048/EDC16_V20_PR048

13B-234
MR-372-J84-13B200$612.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
PR051
EGR VALVE POSITION FEEDBACK
PARAMETER
DEFINITIONThis parameter indicates the EGR valve opening ratio.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
No faults should be present or stored.
Perform this fault finding procedure:
– after finding an inconsistency in the parameter,
– after a customer complaint (loss of power, smoke etc.).
– after interpretation of command AC103 EGR by-pass.
Conformity check with engine stopped and ignition on.
The value must be between – 10% < PR051 < 0%.
In the event of a fault, consult the interpretation of fault DF118 EGR solenoid valve servo-control.
Engine running, engine coolant temperature > 80°C.
The value must be between 10% < PR051 < 40%.
In the event of a fault, consult the interpretation of fault DF118 EGR solenoid valve servo-control.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_PR051/EDC16_V58_PR051/EDC16_V5C_PR051/EDC16_V18_PR051/EDC16_V1C_PR051/EDC16_V20_PR051

13B-235
MR-372-J84-13B200$612.mif
V13
DIESEL INJECTION
Fault finding – Interpretation of parameters
EDC16
Program No: C1
Vdiag No: 18, 1C, 20,
50, 58, 5C
13B
PR053
SPEED REQUESTED BY HEATING/AIR CONDITIONING
PARAMETER
DEFINITIONThis parameter indicates the engine's speed of rotation with air conditioning in rpm.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine running, engine coolant temperature > 80°C.
The engine speed requested by the air conditioning is increased and fluctuates around 875 rpm.
This parameter is only valid when the engine has been started.
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16_V50_PR053/EDC16_V58_PR053/EDC16_V5C_PR053/EDC16_V18_PR053/EDC16_V1C_PR053/EDC16_V20_PR053