2011 RENAULT SCENIC clutch

13B - 141
DIESEL INJECTION
Fault finding - Conformity check13B
V10 MR-372-J84-13B150$470.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
CRUISE-CONTROL/SPEED LIMITER (continued)
NOTESOnly check conformity after a complete check using the diagnostic tool. The values
shown in this conformity check are given as a guide.
Test conditions: engine at idle speed, coolant temperature at > 80°.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
2Cruise
control/
speed
limiter
(continued)ET415: Deactivation
of cruise
control/speed
limiterNONE
STATUS 1: Traction control
request
The cruise control and speed
limiter functions can be
deactivated by various
events.
In the event of a fault,
consult the interpretation of
statuses ET703 Cruise
control/Speed limiter
buttons and ET415 Cruise
control/Speed limiter
deactivation. STATUS 2: Brake pedal
depressed
STATUS 3: Clutch pedal
depressed
STATUS 4: Suspend button
pressed
STATUS 5: Cruise control or
speed limiter monitoring
STATUS 6: Gear lever in
neutral (manual gearbox) or
neutral position (automatic
transmission).
Note: the cruise control
can only be activated at
a speed of >18 mph
(30 km/h).STATUS 7: Inconsistency
between request and vehicle
speed
STATUS 9: Vehicle speed
monitoring
STATUS 10: Monitoring by
injection computer
ET703: Cruise
control/speed
limiter
buttonsINACTIVE: no button
pressed
In the event of a fault,
consult the interpretation of
statuses ET703 Cruise
control/Speed limiter
buttons and ET415 Cruise
control/Speed limiter
deactivation. INCREASE: increase button
pressed
DECREASE: decrease
button pressed
SUSPEND: Suspend button
pressed
RESUME: Resume button
pressed

13B - 142
DIESEL INJECTION
Fault finding - Conformity check13B
V10 MR-372-J84-13B150$470.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
CRUISE-CONTROL/SPEED LIMITER (continued)
NOTESOnly check conformity after a complete check using the diagnostic tool. The values
shown in this conformity check are given as a guide.
Test conditions: engine at idle speed, coolant temperature at > 80°.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
3Brake
switchET704:Brake
switch no. 1
signalIndicates the position of the
brake pedal
With the ignition on, pedal
released:
ET704 = ET705 = INACTIVEIn the event of a fault,
consult the
interpretation of
statuses ET704 and
ET705. ET705:Brake
switch no. 2
signal
4Clutch
SwitchET405:Clutch pedal
switchIndicates the position of the
clutch pedal
With the ignition on, pedal
released:
ET405 = INACTIVEIn the event of a fault,
consult the
interpretation of status
ET405.

13B - 147
DIESEL INJECTION
Fault finding - Status summary table13B
V10 MR-372-J84-13B150$517.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4CDIESEL INJECTION
Fault finding - Status summary table
*RCH: Passenger compartment heating resistorTool Status Diagnostic tool title
ET001+ After ignition computer feed
ET003Engine immobiliser
ET004Air conditioning authorisation
ET007Preheating unit control
ET014Check cooling fan 1
ET015Check cooling fan 2
ET021High speed fan assembly request
ET022Low speed fan assembly request
ET035Reverse gear signal
ET038Engine
ET042Cruise control/speed limiter
ET076Starting
ET077Impact detected
ET078Air regulation
ET079Air conditioning present
ET088Compressor actuation request
ET104Injector code use
ET111RCH* number set
ET112RCH* cut-off
ET233Clutch pedal
ET238Synchronisation
ET341Immobiliser code programmed
ET405Clutch pedal switch
ET413Cruise control/speed limiter function
ET415Deactivation of cruise control/speed limiter
ET703Cruise control/speed limiter buttons
ET704Brake switch no. 1
ET705Brake switch no. 2
MR-372-J84-13B150$517.mif

13B-168
DIESEL INJECTION
Fault finding - Interpretation of statuses13B
V10 MR-372-J84-13B150$564.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
ET405
CLUTCH PEDAL SWITCH
STATUS
DEFINITIONACTIVE: This status indicates that the clutch pedal is depressed.
INACTIVE: This status indicates that the clutch pedal is released.
NOTESSpecial note:
Only perform the tests if the statuses do not correspond with the system programming
functions.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature
> 80°C
ACTIVEClutch pedal depressed.
Non-conformity of the brake signals and or the clutch switch signals can cause the
engine to race during gear changes.
In the event of a fault, check the electrical conformity of the sensor.
INACTIVEClutch pedal released.
Non-conformity of the brake signals and or the clutch switch signals can cause the
engine to race during gear changes.
In the event of a fault, check the electrical conformity of the sensor.
Sensor electrical conformity
ACTIVECheck the condition and fitting of the clutch pedal switch.
Remove the clutch pedal switch then check the insulation between tracks 1 and 2, with
the switch in the rest position.
Repeat this operation with the switch depressed and check the continuity between
tracks 1 and 2.
If these two checks are not in order, replace the switch.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
ET405
CLUTCH PEDAL SWITCH
STATUS
DEFINITIONACTIVE: This status indicates that the clutch pedal is depressed.
INACTIVE: This status indicates that the clutch pedal is released.
NOTESSpecial note:
Only perform the tests if the statuses do not correspond with the system programming
functions.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant temperature
> 80°C
ACTIVEClutch pedal depressed.
Non-conformity of the brake signals and or the clutch switch signals can cause the
engine to race during gear changes.
In the event of a fault, check the electrical conformity of the sensor.
INACTIVEClutch pedal released.
Non-conformity of the brake signals and or the clutch switch signals can cause the
engine to race during gear changes.
In the event of a fault, check the electrical conformity of the sensor.
Sensor electrical conformity
EDC16_V44_ET405/EDC16_V48_ET405/EDC16_V4C_ET405

13B-169
DIESEL INJECTION
Fault finding - Interpretation of statuses13B
V10 MR-372-J84-13B150$564.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
ET405
CONTINUED 1
INACTIVECheck the condition and fitting of the clutch pedal switch.
Remove the clutch pedal switch, check the insulation between tracks 1 and 2 in rest
position.
Repeat this operation with the switch pressed and check the continuity between tracks
1 and 2.
If these two checks are not in order, replace the switch.
Then check the continuity and absence of interference resistance of the following
connection:
Injection computer black 32-track
connector A, track C4Track 1 clutch connector
Check for earth on track 2 of the clutch switch connector.
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.

13B-171
DIESEL INJECTION
Fault finding - Interpretation of statuses13B
V10 MR-372-J84-13B150$564.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
ET415
(CONTINUED 1)
STATUS 2Brake pedal depressed
The cruise control function is deactivated when the brake pedal is depressed.
Status ET415 becomes STATUS 2, when driving with the cruise control active (ET042
Cruise control/Speed limiter: CRUISE CONTROL) and the brake pedal is depressed.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command RZ001
Fault memory.
If status ET415 becomes STATUS 2 with no application of the brake pedal, consult the
interpretation of statuses ET704 and ET705 Brake contact no. 1 and no. 2.
STATUS 3Clutch pedal depressed
Manual gearbox ONLY
The cruise control function is deactivated when the gearbox is not coupled to the engine
(clutch pedal depressed).
Status ET415 becomes STATUS 3 when driving with the cruise control active (ET042
Cruise control/speed limiter: CRUISE CONTROL) and the clutch pedal is depressed.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command RZ001
Fault memory.
If status ET415 becomes STATUS 3 without the clutch pedal being depressed, consult
the interpretation of status ET405 Clutch pedal switch.
If the vehicle is fitted with automatic transmission:
Carry out a multiplex network test, check the configuration of the multiplex network
according to the vehicle's technical specifications and, in particular, the automatic
gearbox computer configuration (see 88B, multiplex).
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.

13B-173
DIESEL INJECTION
Fault finding - Interpretation of statuses13B
V10 MR-372-J84-13B150$564.mif
EDC16 INJECTION
Program No.: C1
Vdiag No.: 44, 48 and 4C
ET415
(CONTINUED 3)
STATUS 6Gear lever in neutral (manual gearbox) or the neutral position (automatic gearbox)
Status ET415 becomes STATUS 6 when driving with the cruise control active (ET042
Cruise control/speed limiter: CRUISE CONTROL) and:
- If the driver puts the gear lever in neutral position on a manual gearbox without
declutching or,
- if the gear lever is in neutral on an automatic gearbox.
This deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command RZ001
Fault memory.
If status ET415 becomes STATUS 6 without shifting the gear lever into neutral on a
manual gearbox without declutching, or into neutral on an automatic transmission, run
fault finding on the ABS computer and check the configuration of the tyre size stored in
the computer. If the configuration is correct, contact the Techline.
STATUS 7Lack of correlation between the request and the vehicle speed
Status ET415 becomes STATUS 7 if the computer detects too great a difference
between the speed requested by the driver and the vehicle speed.
STATUS 7 may occur when driving with the cruise control active (ET042 Cruise control/
speed limiter: CRUISE CONTROL) and on a very uneven surface.
This inconsistency deactivates cruise control.
Reinitialise status ET415 on the injection computer by running command RZ001
Fault memory.
If status ET415 becomes STATUS 7 where the surface is not uneven, contact the
Techline.
AFTER REPAIRDeal with any other faults. Clear the fault memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.

13B-207
MR-372-J84-13B150$846.mif
V10
DIESEL INJECTION
Fault finding - Fault finding chart13B
ALP 3 Injection noise
NOTESBefore dealing with this customer complaint, check that there are no faults,
and the conformity (or otherwise) of the parameters and statuses using the
diagnostic tool.
If the customer complaint is not eliminated, perform the following checks.
If the injection noise occurs after starting from cold:
Check the low pressure diesel circuit priming.
Check the fuel heater supply.
Check the operation of the preheating system.
Check that fuel and engine temperatures are consistent.
If the complaint is still present, check the rail pressure (Parameter menu) and apply the interpretation
of command AC011 Rail pressure regulator.
If the injection noise occurs at idle speed:
Check the condition of the injector connector and pressure regulator terminals.
Check the conformity of the air flow signal (consult parameter PR018 Estimated air flow).
Check the condition of the EGR valve (clogging, blocked, seized).
If the complaint is still present, perform the injector fault finding procedure with Test 1 Injector test.
Does the injection noise occur at all engine speeds?
Carry out fault finding on the injectors with Test 1 Injector Test.
Check the condition of the injector connector and pressure regulator terminals.
Ensure that the correct fuel is being used.
Check the conformity of the air flow signal (consult the interpretation of parameter PR132 Air flow).
If the customer complaint is still present, check the rail pressure (parameter menu) and apply the interpretation
of command AC011 Rail pressure regulator.
If the injection noise occurs at transitional speed:
If the engine races during gear changes, check the conformity of the clutch switch.
When changing gear during a road test, display parameter PR017 Fuel flow. if it varies without greatly affecting
the rail pressure, perform the fault finding procedure for AC011 Rail pressure regulator.
If the fault is still present, carry out a fault finding check on the injectors (seeTEST 1).
AFTER REPAIRCarry out a road test followed by a complete check with the diagnostic tool.
EDC16_V44_ALP3 / EDC16_V48_ALP3 / EDC16_V4C_ALP3EDC16 INJECTION
Program No.: C1
Vdiag No: 44, 48 and 4C