Page 167 of 276
8/
PRACTICAL INFORMATION
ENERGY ECONOMY MODE
System which manages the duration of use of certain functions to
conserve a suffi cient level of charge in the battery.
After the engine has stopped, you can still use functions such as
the audio and telematics system, windscreen wipers, dipped beam
headlamps, courtesy lamp, etc. for a maximum combined duration of
thirty minutes.
This period may be greatly reduced if the battery is not fully charged.
SWITCHING TO ECONOMY MODE
Once this time has elapsed, a message appears in the screen indicating
that the vehicle has switched to economy mode and the active functions
are put on standby.
If the telephone is being used at this time:
- it will be maintained for 5 minutes with the Bluetooth system
of your Peugeot Connect Sound,
- it will still be possible to fi nish the call with the Peugeot
Connect Media.
EXITING ECONOMY MODE
These functions are reactivated automatically next time the vehicle is
driven.
To restore operation of these functions immediately, start the engine
and let it run for at least 5 minutes.
Let the engine run for the period specifi ed to ensure that the battery
charge is suffi cient.
Do not repeatedly and continuously restart the engine in order to charge
the battery.
A fl at battery prevents the engine from starting (refer to the
"Battery" section).
LOAD REDUCTION MODE
System which manages the use of certain functions according to
the level of charge remaining in the battery.
When the vehicle is being driven, the load reduction function temporarily
deactivates certain functions, such as the air conditioning, the heated
rear screen...
The deactivated functions are reactivated automatically as soon as
conditions permit.
Page 170 of 276
168
CHANGING A BULB
The headlamps are fi tted with polycarbonate glass with a
protective coating:
)
do not clean them using a dry or abrasive cloth, nor with
a detergent or solvent product,
)
use a sponge and soapy water,
)
when using a high pressure washer on persistent marks, do
not keep the lance directed towards the lamps or their edges
for too long, so as not to damage their protective coating
and seals.
)
Do not touch the bulb directly with your fi ngers, use lint-free
cloths.
Changing a bulb should only be done after the headlamp has
been switched off for a few minutes (risk of serious burns).
It is imperative to use only anti-ultraviolet (UV) type bulbs in order
not to damage the headlamp.
Always replace a failed bulb with a new bulb with the same type
and specifi cation.
FRONT LAMPS
Model with halogen headlamps
1.
Direction indicators (PY 21W amber).
2.
Dipped beam headlamps (H7 - 55W).
3.
Main beam headlamps (H1 - 55W).
4.
Daytime running lamps/sidelamps (P 21/5W).
5.
Foglamps (H8 - 35W).
Page 171 of 276
8/
PRACTICAL INFORMATION
1.
Direction indicators (PY21W SV silver).
2.
Directional dipped/main beam headlamps (D1S-35W).
3.
Additional main beam headlamps (H1-55W).
4.
Daytime running lamps/sidelamps (P21/5W).
5.
Foglamps (H8-35W).
Model with xenon and directional headlamps
Risk of electrocution
Xenon bulbs (D1S-35W) must be replaced by a PEUGEOT dealer
or a qualifi ed workshop.
Changing direction indicator bulbs
)
Turn the bulb holder a quarter of a turn and extract it.
)
Pull the bulb and change it.
To refi t, carry out these operations in reverse order.
Amber or silver coloured bulbs, such as the direction indicators,
must be replaced with bulbs of identical specifi cations and colour.
When refi tting, close the protective cover carefully to assure
the sealing of the headlamp.
Page 172 of 276
170
Changing dipped beam headlamp bulbs
)
Remove the protective cover by pulling on the tab.
)
Disconnect the bulb connector.
)
Spread the springs to release the bulb.
)
Extract the bulb and change it.
To refi t, carry out these operations in reverse order.
Changing main beam headlamp bulbs
)
Remove the protective cover by pulling on the tab.
)
Disconnect the bulb connector.
)
Compress the springs to release the bulb.
)
Remove the bulb and change it
To refi t, carry out these operations in reverse order.
Changing daytime running lamp/sidelamp bulbs
)
Remove the protective cover by pulling on the tab.
)
Disconnect the bulb connector.
)
Turn the bulb holder a quarter of a turn and extract it.
)
Pull the bulb and change it.
To refi t, carry out these operations in reverse order.
Page 176 of 276
174
Changing sidelamps and direction indicators
For the replacement of this type of LED lamp, contact a PEUGEOT
dealer or a qualifi ed workshop.
High pressure washing
When using this type of washing on stubborn dirt, do not persist
on the headlamps, the lamps and their surrounds to avoid
damaging their protective coating and seals.
Changing number plate lamps (W5W)
)
Insert the end of the vehicle's key in the hole in the transparent
cover.
)
Push towards the outside to unclip it.
)
Remove the transparent cover.
)
Pull the bulb and change it.
Changing the third brake lamp (LEDs)
For the replacement of this type of LED lamp, contact a PEUGEOT
dealer or a qualifi ed workshop.
Page 181 of 276
8/
F10
F11
F13F14F12
F20
F19
F18
F17
F16
F15
F4
F8F2
F3F5 F7
F9
F6
F21 F1
PRACTICAL INFORMATION
ENGINE COMPARTMENT FUSES
The fusebox is placed in the engine compartment near the battery
(left-hand side).
Access to the fuses
)
Unclip the cover.
)
Change the fuse (see corresponding paragraph).
)
When you have fi nished, close the cover carefully to assure the
sealing of the fusebox.
Fuse table
Fuse N°
Rating
Functions
F1
20 A
Engine control unit supply, injection
pump and EGR electrovalves (Diesel),
injectors (Diesel).
F2
15 A
Horn.
F3
10 A
Front wash-wipe.
F4
20 A
Daytime running lamps.
F5
15 A
Air fl ow sensor, coolant pump, oil pump,
thermostat, blow-by heater (petrol),
by-pass and EGR electrovalves (Diesel),
diesel heater (Diesel).
F6
10 A
Steering wheel angle sensor, ABS/ESP
control unit, ESP control unit.
F7
10 A
Power steering control unit, automatic
gearbox, engine coolant level detector,
dual function brake switch.
F8
25 A
Starter motor control.
F9
10 A
Diagnostic socket, directional
headlamps, particle emission fi lter pump
(Diesel).
F10
30 A
Engine control unit actuators (petrol:
ignition coils, electrovalves, injectors,
fuel pump (Diesel: electrovalves,
heaters).
F11
40 A
Air conditioning blower.
Page 182 of 276
F10
F11
F13F14F12
F20
F19
F18
F17
F16
F15
F4
F8F2
F3F5 F7
F9
F6
F21 F1
180
Fuse N°
Rating
Functions
F12
40 A
Windscreen wipers slow/fast speed.
F13
40 A
Built-in systems interface supply (ignition
positive).
F14
-
Not used.
F15
10 A
Right-hand main beam headlamp.
F16
10 A
Left-hand main beam headlamp.
F17
15 A
Left-hand dipped headlamp.
F18
15 A
Right-hand dipped headlamp.
F19
15 A
Variable timing electrovalve, oxygen
sensors (petrol), electrovalves (Diesel).
F20
10 A
Turbine discharge and canister purge
electrovalves (petrol), air fl ow sensor
(1.6 l THP 200), water in diesel sensor
(Diesel).
F21
5 A
Fans control, Turbo pump (petrol),
Valvetronic motor (1.6 l THP 200).
Page 188 of 276
186
CLEANING AND MAINTENANCE
The general recommendations on cleaning and maintaining your vehicle
are given in the Warranty and Maintenance Record.
ALUMINIUM ARCHES
To clean these arches, do not use a dry cloth with an abrasive product.
Use a sponge and soapy water.
PEUGEOT TECHNO TEP
To clean this trim, do not use solvents or detergents with a dry cloth.
First remove dust, then use a soft cloth and soapy water. Dry with
another soft cloth.
HEADLAMPS AND LAMPS
The headlamps have polycarbonate lenses, fi nished with a protective
lacquer.
Do not clean them with a dry or abrasive cloth, nor with detergent or
solvent products.
Use a sponge and soapy water.
CUSTOMISING STICKERS
These customising parts are self-adhesive stickers, treated to give good
resistance to ageing and tearing.
They are intended for customising the body.
Available also as accessories, we recommend that you have them fi tted
by a PEUGEOT dealer or a qualifi ed workshop.
MATT PAINT
If you vehicle is fi nished with a clear matt lacquer, please observe the
following recommendations to avoid damaging the paintwork by the use
of an inappropriate procedures.
These recommendations are also valid for alloy road wheels fi nished
with clear matt lacquer.
The use of a high pressure jet wash for cleaning the headlamps,
lamps and their surrounds may damage the lacquer and seals.
Observe the recommendations on pressure and distance for jet
washing.
First clean persistent stains with a sponge and warm soapy water. When washing your vehicle, keep the end of a high-pressure
lance at least 30 centimetres from the stickers.
Never polish the vehicle body, nor the alloy wheels. Doing this will
make the paintwork shiny.
Do not use paint cleaners, abrasive products or paint polishing or
preserving products (such as wax, for example) on the paintwork.
These products are only suitable for bright fi nishes. Application of
these products on vehicles with a matt fi nish will seriously damage
the paint surface of the vehicle, giving rise to shiny or stained
areas.
Never select a wash programme that fi nishes with a hot wax
cycle.
Always have paint repairs done by a PEUGEOT dealer or a
qualifi ed workshop.
From the range of cleaning and maintenance products recommended and approved
by PEUGEOT, use only products for removing insects and car shampoo.
