Page 32 of 276
30
Operation indicator lamps
If one of the following indicator lamps comes on, this confi rms that the
corresponding system has come into operation.
It may be accompanied by an audible signal.
Depending on your version of instrument panel, illumination of the
indicator lamp may also be accompanied by:
- a pictogramme in the central instrument panel screen and a
message in the multifunction screen,
or
- a pictogramme and a message in the central instrument panel
screen.
Warning lamp
is on
Cause
Action/Observations
Left-hand
direction
indicato
r
fl ashing with
buzzer. The lighting stalk is pushed
down.
Right-hand
direction indicator
fl ashing with
buzzer. The lighting stalk is pushed up.
Hazard warning
lamps
fl ashing with
audible signal. The hazard warning lamps
switch, located on the dashboard,
has been operated. The left-hand and right-hand direction indicators and their
associated indicator lamps fl ash simultaneously.
Sidelamps
fi xed. The lighting stalk is in the
"Sidelamps" position or the
"AUTO" position with low light.
Dipped beam
headlamps
fi xed.
The lighting stalk is in the "Dipped beam
headlamps" position or in the "AUTO"
position in conditions of low light.
Main beam
headlamps
fi xed. The lighting stalk is pulled
towards you. Pull the stalk again to return to dipped beam headlamps.
Page 44 of 276
42
MONOCHROME SCREEN C (WITH
PEUGEOT CONNECT SOUND)
DISPLAYS ON THE SCREEN
This displays the following information:
- time,
- date,
- ambient temperature (this fl ashes if there is a risk of ice),
- state of the openings (doors, boot...),
- visual parking sensors.
- audio functions,
- telephone information and directories.
Warning messages (e.g.: "Emission control system faulty") or
information messages (e.g.: "Automatic lighting of headlamps
activated") may appear temporarily. These can be cleared by pressing
the "ESC"
button.
CONTROLS
From the control panel of your Peugeot Connect Sound, you can:
)
press the "MENU"
button for access to the main menu
,
)
press the "
" or "
" buttons to scroll through the items on the
screen,
)
press the "MODE"
button to change the permanent application
(audio source, telephone...),
)
press the "
" or "
" buttons to change a setting value,
)
press the "OK"
button to confi rm,
or
)
press the "ESC"
button to abandon the operation in progress.
11:32104.6 FM1RTL23Mem1c°
TMC LOUD RDS TATue 21/10/2010
Page 46 of 276
44
"PERSONALISATION-CONFIGURATION"
MENU
Once this menu has been selected, you can gain access to the
following functions:
- defi ne the vehicle parameters,
- display confi guration,
- choice of language.
Define the vehicle parameters
Once this menu has been selected, you can activate or deactivate the
following equipment:
- selective unlocking (refer to the "Access" section),
- guide-me-home and welcome lighting (refer to the "Visibility" and
"Ergonomics and Comfort" sections),
- interior mood lighting (refer to the "Ergonomics and Comfort" section),
- daytime running lamps (refer to the "Visibility" section),
- rear parking sensors (refer to the "Driving" section).
)
Press the "
" or "
" buttons, then the "OK"
button to select the
"Guide-me-home headlamps" line.
)
Press the "
" or "
" buttons to set the value required (15, 30 or
60 seconds), then press the "OK"
button to confi rm.
)
Press the "
" or "
" buttons, then the "OK"
button to select the
"OK"
box and confi rm or press the "ESC"
button to cancel.
Example: setting of the duration of the guide-me-home lighting
)
Press the "
" or "
" buttons, then the "OK"
button to select the
menu required.
Page 72 of 276
70
REAR VIEW MIRROR
Adjustable mirror providing a central rearward view.
Equipped with an anti-dazzle system, which darkens the mirror glass:
this reduces the nuisance to the driver caused by the headlamps
from following vehicles, low sun...
Manual day/night model
Adjustment
)
Adjust the mirror so that the glass is directed correctly
in the "day" position.
Day/night position
)
Pull the lever to change to the "night" anti-dazzle position.
)
Push the lever to change to the normal "day" position.
As a safety measure, the mirrors should be adjusted to reduce
the "blind spot".
Automatic day/night model
In order to ensure optimum visibility during your manoeuvres,
the mirror lightens automatically when reverse gear is engaged.
By means of a sensor, which measures the light from the rear of the
vehicle, this system automatically and progressively changes between
the day and night uses.
Due to the curve of the rear screen, the image in the rear view
mirror may be slightly distorted; take this into account when
manoeuvring the vehicle.
Page 81 of 276
3/
EASE OF USE and COMFORT
EXTERIOR WELCOME LIGHTING
The remote switching on of the lighting makes your approach to the
vehicle easier in poor light. It is activated according to the level of light
detected by the sunshine sensor.
SWITCHING ON
)
Press the open padlock on the remote control.
The dipped beam headlamps and the sidelamps come on;
your vehicle is also unlocked.
PROGRAMMING
The duration of the welcome lighting is associated with and
identical to that of the automatic guide-me-home lighting.
The lighting duration is selected via the vehicle
confi guration menu.
SWITCHING OFF
The exterior welcome lighting switches off automatically after a set time,
when the ignition is switched on or on locking the vehicle.
Page 90 of 276
88
EXTERIOR LIGHTING
CONTROLS
Control stalk for the selection and control of the various front and rear
lamps providing the vehicle's lighting.
MAIN LIGHTING
The various front and rear lamps of the vehicle are designed to adapt
the driver's visibility progressively in relation to the climatic conditions:
- sidelamps, to be seen,
- dipped beam headlamps to see without dazzling other drivers,
- main beam headlamps to see clearly when the road is clear.
ADDITIONAL LIGHTING
Other lamps are fi tted to fulfi l the requirements of particular driving
conditions:
- a rear foglamp to be seen from a distance,
- front foglamps for even better forward vision,
- directional headlamps for improved visibility when cornering,
- daytime running lamps to be seen during the day.
PROGRAMMING
Various automatic lighting control modes are also available depending
on options:
- guide-me-home lighting,
- automatic illumination of headlamps,
- directional lighting.
In some weather conditions (e.g. low temperature or humidity),
the presence of misting on the internal surface of the glass of the
headlamps and rear lamps is normal; it disappears after the lamps
have been on for a few minutes.
Page 91 of 276
4/
VISIBILITY
Model without AUTO lighting
Model with AUTO lighting
MANUAL CONTROLS
The lighting commands are issued directly by the driver by means of the
ring A
and the stalk B
.
A.
Main lighting mode selection ring: turn it to position the symbol
required facing the mark.
Lamps off.
Automatic illumination of headlamps.
B.
Stalk for switching headlamps: pull it to switch between dipped
headlamps/main beam headlamps.
In the lamps off and sidelamps modes, the driver can switch on the
main beam headlamps temporarily ("headlamp fl ash") by maintaining a
pull on the stalk. Sidelamps only.
Dipped or main beam headlamps.
DISPLAYS
Lighting of the corresponding indicator lamp on the instrument panel
confi rms the switching on of the lighting selected.
The instrument panel has permanent back-lighting, both day and night.
In this case, illumination of the instrument panel is not linked to the
exterior lighting.
Page 92 of 276
90
C.
Foglamp selection ring.
The foglamps operate with the dipped and main beam headlamps.
Front and rear foglamps.
Press, turning ring C
:
)
forwards once to switch on the front foglamps,
)
forwards again to switch on the rear foglamp,
)
rearwards once to switch off the rear foglamp,
)
rearwards again to switch off the front foglamps.
When the lighting is switched off automatically (with AUTO model) or
when the dipped beam headlamps are switched off manually, the front
foglamps and the sidelamps will remain on.
)
Turn the ring rearwards to switch off the front foglamps,
the sidelamps will then switch off.
In good or rainy weather, both day and night, the front foglamps
and the rear foglamp are prohibited. In these situations, the power
of their beams may dazzle other drivers. They should only be
used in fog or snow.
In these weather conditions, it is your responsibility to switch
on the foglamps and dipped beam headlamps manually as the
sunshine sensor may detect suffi cient light.
Do not forget to switch off the front foglamps and the rear foglamp
when they are no longer necessary.
Switching off of the lamps when the ignition is switched off
On switching off the ignition, all of the lamps turn off immediately,
except for dipped beam if guide-me-home lighting is activated.
Switching on the lamps after the ignition is switched off
To reactivate the lighting control, rotate ring A
to the "0"
position -
lamps off, then to the desired position.
On opening the driver's door a temporary audible signal warns the
driver that the lighting is on.
The lamps, with the exception of the sidelamps, switch off
automatically after a maximum duration of thirty minutes to
prevent discharging of the battery.
