2011 NISSAN LATIO wiring

DI-1
ELECTRICAL
C
DE
F
G H
I
J
L
M
SECTION DI
A
B
DI
N
O P
CONTENTS
DRIVER INFORMATION SYSTEM
SERVICE INFORMATION .. ..........................2
PRECAUTION ................................................ .....2
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ............................................................. ......
2
Precaution Necessary for Steering Wheel Rota-
tion After Battery Disconnect ............................... ......
2
COMBINATION METERS ...................................4
Component Parts and Harness Connector Loca-
tion ...................................................................... ......
4
System Description ...................................................4
Arrangement of Combination Meter ..........................6
Internal Circuit ...........................................................7
Wiring Diagram - METER - .......................................8
Combination Meter Harness Connector Terminal
Layout .....................................................................
10
Terminal and Reference Value for Combination
Meter .......................................................................
10
Self-Diagnosis Mode of Combination Meter ........ ....11
CONSULT-III Function (METER/M&A) ............... ....13
Trouble Diagnosis ...................................................14
Symptom Chart .......................................................15
Power Supply and Ground Circuit Inspection .........15
Vehicle Speed Signal Inspection .............................16
Engine Speed Signal Inspection .............................17
Fuel Level Sensor Signal Inspection .......................17
Fuel Gauge Fluctuates, Indicates Wrong Value, or
Varies ......................................................................
19
Fuel Gauge Does Not Move to Full-position ...........19
DTC [U1000] CAN Communication Circuit ......... ....19
Electrical Component Inspection .............................20
Removal and Installation .........................................20
WARNING LAMPS ......................................... ....21
Schematic ........................................................... ....21
Wiring Diagram - WARN - ................................... ....22
Oil Pressure Warning Lamp Stays Off (Ignition
Switch ON) .......................................................... ....
30
Oil Pressure Warning Lamp Does Not Turn Off
(Oil Pressure Is Normal) ...................................... ....
32
Component Inspection .............................................32
A/T INDICATOR ................................................34
System Description ..................................................34
Wiring Diagram - AT/IND - .......................................35
A/T Indicator Does Not Illuminate ............................36
CVT INDICATOR ...............................................38
System Description ..................................................38
Schematic ................................................................38
Wiring Diagram - CVTIND - .....................................39
CVT Indicator Does Not Illuminate ..........................41
WARNING CHIME .............................................43
Component Parts and Harness Connector Loca-
tion ....................................................................... ....
43
System Description ..................................................43
Wiring Diagram - CHIME - .......................................46
Terminal and Reference Value for BCM ..................47
CONSULT-III Function (B CM) .................................47
Trouble Diagnosis ................................................ ....48
Combination Meter Buzzer Circuit Inspection .........49
Front Door Switch LH Signal Inspection .............. ....50
Key Switch Signal Inspection (Without Intelligent
Key) ..................................................................... ....
51
Key Switch and Ignition Knob Switch Signal In-
spection (With Intelligent Key, When Mechanical
Key Is Used) ........................................................ ....
52
Lighting Switch Signal Inspection ............................54
Parking Brake Switch Signal Inspection ..................54
Electrical Component Inspection .............................55
Revision: May 2010 2011 Versa

DI-2
< SERVICE INFORMATION >
PRECAUTION
SERVICE INFORMATION
PRECAUTION
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000006412029
The Supplemental Restraint System such as “A IR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and w hether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inopera tive, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including in correct removal and installation of the SRS, can lead to personal
injury caused by unintent ional activation of the system. For re moval of Spiral Cable and Air Bag
Module, see the SRS section.
• Do not use electrical test equipmen t on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harn esses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electri c power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor( s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers , always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minu tes before performing any service.
Precaution Necessary for Steering W heel Rotation After Battery Disconnect
INFOID:0000000006412030
NOTE:
• This Procedure is applied only to models with Intelligent Key system and NATS (NISSAN ANTI-THEFT SYS-
TEM).
• Remove and install all control units after disconnecting both battery cables with the ignition knob in the
″LOCK ″ position.
• Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If DTC is detected, perform trouble diagnosis according to self-diagnostic results.
For models equipped with the Intelligent Key system and NATS, an electrically controlled steering lock mech-
anism is adopted on the key cylinder.
For this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock and
steering wheel rotation will become impossible.
If steering wheel rotation is required when battery pow er is interrupted, follow the procedure below before
starting the repair operation.
OPERATION PROCEDURE
1. Connect both battery cables. NOTE:
Supply power using jumper cables if battery is discharged.
2. Use the Intelligent Key or mechanical key to turn the ignition switch to the ″ACC ″ position. At this time, the
steering lock will be released.
3. Disconnect both battery cables. The steering lock will remain released and the steering wheel can be rotated.
4. Perform the necessary repair operation.
Revision: May 2010 2011 Versa

DI-8
< SERVICE INFORMATION >
COMBINATION METERS
Wiring Diagram - METER -
INFOID:0000000005929163
ABNWA0613GB
Revision: May 2010 2011 Versa

DI-22
< SERVICE INFORMATION >
WARNING LAMPS
Wiring Diagram - WARN -
INFOID:0000000005929180
ABNWA0594GB
Revision: May 2010 2011 Versa

A/T INDICATORDI-35
< SERVICE INFORMATION >
C
DE
F
G H
I
J
L
M A
B
DI
N
O P
Wiring Diagram - AT/IND -INFOID:0000000005929185
LKWA0360E
Revision: May 2010 2011 Versa

CVT INDICATORDI-39
< SERVICE INFORMATION >
C
DE
F
G H
I
J
L
M A
B
DI
N
O P
Wiring Diagram - CVTIND -INFOID:0000000005929189
LKWA0362E
Revision: May 2010 2011 Versa

DI-46
< SERVICE INFORMATION >
WARNING CHIME
Wiring Diagram - CHIME -
INFOID:0000000005929193
ABNWA0847GB
Revision: May 2010 2011 Versa

EC-2
System Diagram ....................................................56
System Description .................................................56
Component Parts Location ...................................57
Component Description ..........................................61
AIR CONDITIONING CUT CONTROL ..............63
System Diagram .................................................. ...63
System Description .................................................63
Component Parts Location ...................................64
Component Description ..........................................68
CAN COMMUNICATION ...................................70
System Description .................................................70
COOLING FAN CONTROL ...............................71
System Diagram .................................................. ...71
System Description .................................................71
Component Parts Location ...................................73
Component Description ..........................................77
EVAPORATIVE EMISSION SYSTEM ...............79
System Diagram .................................................. ...79
System Description .................................................79
Component Parts Location ...................................83
Component Description .........................................87
INTAKE VALVE TIMING CONTROL .................89
System Diagram .................................................. ...89
System Description .................................................89
Component Parts Location ...................................90
Component Description ..........................................94
ON BOARD DIAGNOSTIC (OBD) SYSTEM .....95
Diagnosis Description .......................................... ...95
GST (Generic Scan Tool) .......................................95
DIAGNOSIS SYSTEM (ECM) ............................96
DIAGNOSIS DESCRIPTION .................................. ...96
DIAGNOSIS DESCRIPTION : 1st Trip Detection
Logic and Two Trip Detection Logic .......................
96
DIAGNOSIS DESCRIPTION : DTC and Freeze
Frame Data .............................................................
96
DIAGNOSIS DESCRIPTION : Counter System .....97
DIAGNOSIS DESCRIPTION : Driving Pattern ......100
DIAGNOSIS DESCRIPTION : System Readiness
Test (SRT) Code ................................................. ..
101
DIAGNOSIS DESCRIPTION : Permanent Diag-
nostic Trouble Code (Permanent DTC) .................
102
DIAGNOSIS DESCRIPTION : Malfunction Indica-
tor Lamp (MIL) ..................................................... ..
103
On Board Diagnosis Function ................................103
CONSULT-III Function ..........................................106
COMPONENT DIAGNOSIS .......................114
TROUBLE DIAGNOSIS - SPECIFICATION
VALUE ............................................................ .
114
Description ........................................................... ..114
Component Function Check ..................................114
Diagnosis Procedure .............................................115
TROUBLE DIAGNOSIS FOR INTERMITTENT
INCIDENT .........................................................
122
Description ........................................................... .122
Diagnosis Procedure .............................................122
POWER SUPPLY AND GROUND CIRCUIT ....123
Wiring Diagram .................................................... .123
Diagnosis Procedure .............................................123
Ground Inspection .................................................127
U0101 CAN COMM CIRCUIT ...........................128
Description ........................................................... .128
DTC Logic .............................................................128
Wiring Diagram .....................................................129
Diagnosis Procedure .............................................129
U0140 CAN COMM CIRCUIT ...........................130
Description ........................................................... .130
DTC Logic .............................................................130
Wiring Diagram .....................................................131
Diagnosis Procedure .............................................131
U1001 CAN COMM CIRCUIT ...........................132
Description ........................................................... .132
DTC Logic .............................................................132
Wiring Diagram .....................................................133
Diagnosis Procedure .............................................133
P0011 IVT CONTROL ......................................134
DTC Logic ............................................................ .134
Diagnosis Procedure .............................................135
Component Inspection ..........................................136
P0031, P0032 A/F SENSOR 1 HEATER ..........138
Description ........................................................... .138
DTC Logic .............................................................138
Wiring Diagram .....................................................139
Diagnosis Procedure .............................................139
Component Inspection ..........................................141
P0037, P0038 HO2S2 HEATER .......................142
Description ........................................................... .142
DTC Logic .............................................................142
Wiring Diagram .....................................................143
Diagnosis Procedure .............................................143
Component Inspection ..........................................145
P0075 IVT CONTROL SOLENOID VALVE ......146
Description ........................................................... .146
DTC Logic .............................................................146
Wiring Diagram .....................................................147
Diagnosis Procedure .............................................147
Component Inspection ..........................................148
P0101 MAF SENSOR .......................................150
Description ........................................................... .150
DTC Logic .............................................................150
Component Function Check .................................151
Wiring Diagram .....................................................153
Diagnosis Procedure .............................................153
Component Inspection ..........................................155
Revision: May 2010 2011 Versa