2011 MITSUBISHI GALANT lock

7-50 Vehicle care and maintenance
7
Front turn-signal and parking lights
N00917300424
1. Turn the bulb socket counterclockwise to remove it. And
remove the bulb from the socket by turning it counter-
clockwise while pressing in.
2. To install the bulb, perform the removal steps in reverse.
Front side-marker lights
N00943400282
1. Turn the bulb socket counterclockwise to remove it. And
remove the bulb from the socket by pulling out.
2. To install the bulb, perform the removal steps in reverse.
BK0121200US.book 50 ページ ２０１０年４月１４日　水曜日　午前１１時２４分

Vehicle care and maintenance
7-51
7
Front fog lights
(if so equipped)
N00943600691
1. Remove the clips (A) and screws (B), then remove the
cover (C).2. Remove the socket and bulb assembly (D) by turning it
counterclockwise.
BK0121200US.book 51 ページ ２０１０年４月１４日　水曜日　午前１１時２４分

7-52 Vehicle care and maintenance
7
3. Pull part (E) in the direction of the arrow (F) to undo the
lock, thereby freeing the fog light bulb from the connec-
tor.
4. To install the bulb, perform the removal steps in reverse.
CAUTION
!
Handle halogen light bulb with care. The gas inside
a halogen light bulb is highly pressurized, so drop-
ping, knocking, or scratching a halogen light bulb
can cause it to shatter.
Never hold the halogen lights bulb with a bare hand,
dirty glove, etc. The oil from your hand could cause
the bulb to break the next time the fog lights are
used.
If the glass surface is dirty, clean it with alcohol and
let it dry completely before installing the bulb.
BK0121200US.book 52 ページ ２０１０年４月１４日　水曜日　午前１１時２４分

Vehicle care and maintenance
7-53
7
Rear combination lights
N00943700416
1. Open the lid.
Partially take off the trim cover (A).2. Remove each socket and bulb assembly by turning it
counterclockwise.
3. To install the bulb, perform the removal steps in reverse.
B- Rear turn-signal light
Remove the bulb by pulling it out.
C- Tail and stop light
Remove the bulb by pulling it out.
BK0121200US.book 53 ページ ２０１０年４月１４日　水曜日　午前１１時２４分

Vehicle care and maintenance
7-55
7
3. Remove the socket and bulb assembly by turning it coun-
terclockwise.4. Remove the bulb by pulling it out.E- Back-up light
BK0121200US.book 55 ページ ２０１０年４月１４日　水曜日　午前１１時２４分

7-58 Vehicle care and maintenance
7
3. Open the trunk lid.
Remove the socket and bulb assembly by turning it coun-
terclockwise.4. Remove the bulb by pulling it out.
5. To install the bulb, perform the removal steps in reverse.
BK0121200US.book 58 ページ ２０１０年４月１４日　水曜日　午前１１時２４分

7-62 Vehicle care and maintenance
7Cleaning the inside of your vehicle
N00945200037
After washing the inside of your vehicle with any cleaner, wipe
it dry in a shady, well ventilated area. NOTE
Always read the instructions on the cleaner label.Plastic, vinyl leather, fabric and flocked parts
N00945300041
1. Lightly wipe these off with a soft cloth soaked in a 3%
solution of gentle soap and water.
2. Dip cloth in fresh water and wring out well. Using this
cloth, wipe off the detergent thoroughly.NOTE
Do not use cleaners, conditioners, or protectants contain-
ing silicone or wax.
Such products may cause annoying reflections and
obscure vision.
Upholstery
N00945500030
1. To maintain the value of your new vehicle, maintain the
upholstery carefully and keep the interior clean.
Use a vacuum cleaner and brush to clean the seats. If
stained, vinyl and synthetic leather should be cleaned with
an appropriate cleaner. Cloth fabrics can be cleaned with
either upholstery cleaner or a 3% solution of gentle soap
in lukewarm water.
2. Clean the carpeting with a vacuum cleaner and remove
any stains with carpet cleaner. Oil and grease can be
removed by lightly dabbing with a clean white cloth and
spot remover. NOTE
If fuzzing is difficult to remove from the seat upholstery,
draw a suitable defuzzing brush over the surface in one
direction.Genuine leather
(if so equipped)
N00945600262
1. To clean, lightly wipe the leather with a soft cloth soaked
in a 5 % solution of gentle soap and water.
2. To rinse, dip the cloth in fresh water, wring it out well, and
wipe off all the soap.
3. To preserve and protect, use a leather protecting agent on
the genuine leather surface. NOTE
If genuine leather is wet with water, wipe it with a dry,
soft cloth.
If left damp, mildew may grow and damage the leather
surface.
CAUTION
!
Do not use organic substances (solvents, kerosene,
alcohol, gasoline, etc.) or alkaline or acidic solutions.
These chemicals can cause discoloring, staining or
cracking of the surface.
If you use cleaners or polishing agents, make sure
their ingredients do not include the substances men-
tioned above.
BK0121200US.book 62 ページ ２０１０年４月１４日　水曜日　午前１１時２４分

9-2 Specifications
9Vehicle labeling
N01147400638
Keep a record of the vehicle identification number. This infor-
mation will assist the police if your vehicle is stolen.1 - Vehicle emission control information labelThe vehicle emission control information label is affixed on the
underside of the engine hood.2 - Vehicle identification number plateThe vehicle identification number is stamped on the plate riv-
eted to the left front corner of the dashboard. It is visible from
outside of the vehicle through the windshield.3 - Air conditioning labelThe air conditioning label is affixed on the underside of the
engine hood.
Engine serial numberThe engine serial number is stamped on the cylinder block as
shown in the illustration. *- Front of the vehicle
BK0121200US.book 2 ページ ２０１０年４月１４日　水曜日　午前１１時２４分