3. Step back while the pressure releases.
4. When you are sure that all the pressure has been released, use the
cloth to turn it counterclockwise and remove the cap.
5. Fill the coolant reservoir slowly with the proper coolant mixture, to
within the COLD FILL RANGE or the FULL COLD level on the
reservoir. If you removed the radiator cap in an overflow system, fill
the radiator until the coolant is visible and radiator is almost full.
6. Replace the cap. Turn until tightly installed. Cap must be tightly
installed to prevent coolant loss.
After any coolant has been added, check the coolant concentration (refer
toChecking engine coolant). If the concentration is not 50/50
(protection to –34°F/–36°C), drain some coolant and adjust the
concentration. It may take several drains and additions to obtain a 50/50
coolant concentration.
Whenever coolant has been added, the coolant level in the coolant
reservoir should be checked the next few times you drive the vehicle. If
necessary, add enough 50/50 concentration of engine coolant and
distilled water to bring the liquid level to the proper level.
If you have to add more than 1.0 quart (1.0 liter) of engine coolant per
month, have your authorized dealer check the engine cooling system.
Your cooling system may have a leak. Operating an engine with a low
level of coolant can result in engine overheating and possible engine
damage.
Recycled engine coolant
Not all coolant recycling processes produce coolant which meets
Mazda recommended coolants. Use of a recycled engine coolant
which does not meet the Mazda recommended coolant, may harm
engine and cooling system components.
Always dispose of used automotive fluids in a responsible manner.
Follow your community’s regulations and standards for recycling and
disposing of automotive fluids.
Coolant refill capacity
To find out how much fluid your vehicle’s cooling system can hold, refer
toMaintenance product specifications and capacitiesin this chapter.
Fill your engine coolant reservoir as outlined inAdding engine coolant
in this section.
Maintenance and Specifications
285
2011 Tribute(j14)
Owners Guide, 1st Printing
USA(fus)
MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIES
Item ApplicationPart name or
equivalentCapacity
Brake fluid and (clutch
fluid–if equipped)AllHigh Performance DOT 3
Motor Vehicle Brake
FluidBetween MIN and MAX
on reservoir
Engine coolant2.5L engine•MazdaPremium
Gold Engine Coolant
(yellow-colored)
•MazdaSpecialty
Orange Engine Coolant
1
7.4 quarts (7.0L)
3.0L engine 9.5 quarts (9.0L)
Engine oil (including
filter change)2.5L engine
SAE 5W-20 Motor Oil5.3 quarts (5.0L)
3.0L engine 6.0 quarts (5.7L)
Power Transfer Unit
Fluid4WD with
automatic
transmissionAPI service GL-5
SAE 75W-140 Synthetic
Lubricant
12 ounces (0.35L)
4WD with manual
transmissionAPI service GL-5
SAE 80W-90
Manual transmission
fluidManual
transmissionAPI service GL-4
SAE 75W-902.4 quarts (2.3L)
2
Automatic transmission
fluidAutomatic
transmissionMERCONLV AT F
3
9.0 quarts (8.5L)
4
Rear axle fluid 4WDSAE 80W-90 Axle
Lubricant2.4 pints (1.15L)
5
Maintenance and Specifications
309
2011 Tribute(j14)
Owners Guide, 1st Printing
USA(fus)
Item ApplicationPart name or
equivalentCapacity
Windshield washer fluid AllUltra-Clear Windshield
Washer ConcentrateFill as required
Fuel tank All — 17.5 gallons (66.2L)
1Add the coolant type originally equipped in your vehicle. Check the coolant reservoir bottle
labeling for the correct fluid type to use. Do not mix different colors or types of coolant. Do not
use Mazda Extended Life Engine Coolant (orange in color). Refer toAdding engine coolantin
this chapter.2Service refill capacity is determined by filling the transmission to the bottom of the filler hole with
the vehicle on a level surface.3Automatic transmissions that require MERCONLV should only use MERCONLV fluid. Refer to
scheduled maintenanceto determine the correct service interval. Use of any fluid other than the
recommended fluid may cause transmission damage.4Indicates only approximate dry-fill capacity. Some applications may vary based on cooler size and
if equipped with an in-tank cooler. The amount of transmission fluid and fluid level should be set
by the indication on the dipstick’s normal operating range.5Fill from 1/4 inch to 9/16 inch (6mm to 14mm) below bottom of fill hole.
Maintenance and Specifications
310
2011 Tribute(j14)
Owners Guide, 1st Printing
USA(fus)
