2011 INFINITI QX56 warning

SR-14
< REMOVAL AND INSTALLATION >
SPIRAL CABLE
SPIRAL CABLE
Exploded ViewINFOID:0000000006113053
Removal and InstallationINFOID:0000000006113054
WARNING:
 Before servicing, turn ignition switch OFF, disconnect battery ne gative terminal and wait 3 minutes
or more.
 Never use the air tools or electric tools for servicing.
REMOVAL
1. Remove the driver air bag module. Refer to SR-11, "Removal and Installation".
2. Remove the steering wheel. Refer to ST-33, "
Removal and Installation".
3. Remove the steering column upper cover and steering column lower cover. Refer to IP-14, "
Removal and
Installation".
1. Steering column upper cover 2. Steering column lower cover 3. Side lid LH
4. TORX bolt LH 5. Driver air bag module 6. Side lid RH
7. TORX bolt RH 8. Steering wheel 9. Spiral cable
10. Steering angle sensor 11. Steering column assembly 12. Combination switch
: Pawl
Refer to GI-4, "
Components" for symbols in the figure.
JMHIA1472GB
Revision: 2010 May2011 QX56

SR-16
< REMOVAL AND INSTALLATION >
SPIRAL CABLE
 Fix the driver air bag module harnesses to the harness fixinghook (A).
 If malfunction is detected by the air bag warnin g lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using sel f-diagnosis or CONSULT-III. Refer to SRC-14, "
On Board
Diagnosis Function" or SRC-19, "CONSULT-III Function".
 After the work is completed, check that no system malfunction is detected by air bag warning lamp.
JMHIA1485ZZ
Revision: 2010 May2011 QX56

FRONT PASSENGER AIR BAG MODULESR-17
< REMOVAL AND INSTALLATION >
C
DE
F
G
I
J
K L
M A
B
SR
N
O P
FRONT PASSENGER AIR BAG MODULE
Exploded ViewINFOID:0000000006113055
Removal and InstallationINFOID:0000000006113056
WARNING:
 Before servicing, turn ignition switch OFF, disconnect battery ne gative terminal and wait 3 minutes
or more.
 Always work from the side of air bag module. Never work in front of it.
 Never use the air tools or el ectric tools for servicing.
REMOVAL
1. Remove the instrument panel assembly. Refer to IP-14, "Removal and Installation".
2. Remove the front passenger air bag module fixing screws (A).
1. Instrument panel assembly 2. Steering member assembly 3. Front passenger air bag module
Refer to GI-4, "
Components" for symbols in the figure.
JMHIA1473GB
JMHIA1487ZZ
Revision: 2010 May2011 QX56

SR-18
< REMOVAL AND INSTALLATION >
FRONT PASSENGER AIR BAG MODULE
3. Disconnect the front passenger air bag module fixing pawls withremover tool (A).
4. Lift up front passenger air bag module, and then remove front passenger air bag module.
CAUTION:
 Always place the front passenger air bag module with pad side facing upward.
 Never impact the front passenger air bag module.
 Replace the front passenger air bag module if it has been dropped or sustained an impact.
 Never insert any foreign objects (screwdriver, etc.) into the front passenger air bag module.
 Never disassemble the front passenger air bag module.
 Never expose the front passenger air bag module to temperatures exceeding 90 °C (194 °F).
 Never allow oil, grease, detergent, or water to co me in contact with the front passenger air bag mod-
ule.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
 Never use the old fixing bolts afte r removal, replace with the new bolts.
 Never damage the harness while installing.
 If malfunction is detected by the air bag warnin g lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using sel f-diagnosis or CONSULT-III. Refer to SRC-14, "
On Board
Diagnosis Function" or SRC-19, "CONSULT-III Function".
 After the work is completed, check that no system malfunction is detected by air bag warning lamp.
JMHIA1488ZZ
: Upward
JMHIA0661ZZ
JMHIA0009ZZ
Revision: 2010 May2011 QX56

SIDE CURTAIN AIR BAG MODULESR-19
< REMOVAL AND INSTALLATION >
C
DE
F
G
I
J
K L
M A
B
SR
N
O P
SIDE CURTAIN AIR BAG MODULE
Exploded ViewINFOID:0000000006113059
Removal and InstallationINFOID:0000000006113060
WARNING:
 Before servicing, turn ignition switch OFF, disconnect battery ne gative terminal and wait 3 minutes
or more.
 Always work from the side of air bag module. Never work in front of it.
 Never use the air tools or el ectric tools for servicing.
REMOVAL
1. Remove the headlining assembly. Refer to INT-29, "Removal and Installation".
2. Remove the side curtain air bag module harness connector. CAUTION:
1. Side curtain air bag
*: Side curtain air bag RH side only
Refer to GI-4, "
Components" for symbols in the figure.
JMHIA1474GB
Revision: 2010 May2011 QX56

SIDE CURTAIN AIR BAG MODULESR-21
< REMOVAL AND INSTALLATION >
C
DE
F
G
I
J
K L
M A
B
SR
N
O P
 Never damage the harness while installing.
 If malfunction is detected by the air bag warnin g lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using sel f-diagnosis or CONSULT-III. Refer to SRC-14, "
On Board
Diagnosis Function" or SRC-19, "CONSULT-III Function".
 After the work is completed, check that no system malfunction is detected by air bag warning lamp.
Revision: 2010 May2011 QX56

SR-22
< REMOVAL AND INSTALLATION >
CRASH ZONE SENSOR
CRASH ZONE SENSOR
Exploded ViewINFOID:0000000006216179
Removal and InstallationINFOID:0000000006216180
WARNING:
 Before servicing, turn ignition switch OFF, disconnect battery ne gative terminal and wait 3 minutes
or more.
 Never use the air tools or electric tools for servicing.
REMOVAL
1. Remove the front under cover. Refer to EXT-25, "Removal and Installation".
2. Disconnect the crash zone sensor harness connector.
3. Remove the crash zone sensor fixing nut, and then remove crash zone sensor.
CAUTION:
 Never impact the crash zone sensor.
 Replace the crash zone sensor if it has been dropped or sus-
tained an impact.
1. Crash zone sensor
Refer to GI-4, "
Components" for symbols in the figure.
JMHIA1583GB
JMHIA0009ZZ
Revision: 2010 May2011 QX56

CRASH ZONE SENSORSR-23
< REMOVAL AND INSTALLATION >
C
DE
F
G
I
J
K L
M A
B
SR
N
O P
 Replace the crash zone sensor of deployed driver air bag and deployed front passenger air bag.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
 Never use the old fixing nut afte r removal, replace with the new nut.
 Never damage the harness co nnector while installing.
 If malfunction is detected by the air bag warnin g lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using sel f-diagnosis or CONSULT-III. Refer to SRC-14, "
On Board
Diagnosis Function" or SRC-19, "CONSULT-III Function".
 After the work is completed, check that no system malfunction is detected by air bag warning lamp.
Revision: 2010 May2011 QX56