2011 INFINITI QX56 transmission

P1734 7GR INCORRECT RATIOTM-143
< DTC/CIRCUIT DIAGNOSIS > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
3. Keep the current driving status for 2 seconds or more if CONSULT-III screen changes from “OUT OF
CONDITION” to “TESTING”.
CAUTION:
When “TESTING” is not indicated on CONSULT-III for a long time, check “Self Diagnostic Results”
in “TRANSMISSION”. When a DTC other than “P1734” is detected, check the DTC. Refer to TM-78,
"DTC Index".
With GST
1. Drive vehicle and maintain the following conditions for 2 seconds or more.
2. Check DTC.
Is
“OUT OF CONDITION”, “STOP VEHICLE” or “COMPLETED RESULT NG” displayed? / Is “P1734”
detected?
YES-1 (OUT OF CONDITION) >>Perform “Step 3” again.
YES-2 (STOP VEHICLE)>>GO TO 4.
YES-3 (COMPLETED RESULT NG)>>Go to TM-143, "
Diagnosis Procedure".
YES-4 (“P1734” is detected)>>Go to TM-143, "
Diagnosis Procedure".
NO >> GO TO 4.
4.CHECK SYMPTOM (PART 2)
With CONSULT-III
1. Stop vehicle.
2. Drive vehicle in “D” position allowing it to shift from 1GR to 7GR and check shift timing and shift shock.
>> INSPECTION END
Diagnosis ProcedureINFOID:0000000006226863
1.DETECT MALFUNCTIONING ITEM
Disassemble the A/T assembly to check component parts. Refer to TM-226, "
Disassembly".
NOTE:
Check the component parts, referring to “Possibl e cause” in “DTC DETECTION LOGIC”. Refer to TM-142,
"DTC Logic".
Is the inspection result normal?
YES >> Replace the control valve & TCM. Refer to TM-182, "Exploded View".
NO >> Repair or replace damaged parts.
GEAR : 7th
ACCELE POSI : 0.7/8 or more
VEHICLE SPEED : 10 km/h (7 MPH) or more
Selector lever : “M” position
Gear position : 7th
Accelerator pedal opening : 0.7/8 or more
Vehicle speed : 10 km/h (7 MPH) or more
Revision: 2010 May2011 QX56

TM-144
< DTC/CIRCUIT DIAGNOSIS >[7AT: RE7R01B]
P1815 M-MODE SWITCH
P1815 M-MODE SWITCH
DTC LogicINFOID:0000000006226864
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” is previously c onducted, always turn ignition switch OFF and wait at
least 10 seconds before performing the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT-III
1. Turn ignition switch ON.
2. Select “SLCT LVR POSI” and “MANU MODE SW ” in “Data Monitor” in “TRANSMISSION”.
3. Maintain the following each conditions more than 2 seconds.
4. Perform “Self Diagnostic Results” in “TRANSMISSION”.
Is
“P1815” detected?
YES >> Go to TM-144, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006226865
1.CHECK MANUAL MODE SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect A/T shift selector connector.
3. Turn ignition switch ON.
4. Check voltage between A/T shift selector vehicle side harness connector terminals.
Is the inspection result normal?
YES >> GO TO 2.
NO >> GO TO 3.
2.CHECK MANUAL MODE SWITCH
DTC Trouble diagnosis name DTC is detected if... Possible cause
P1815 Manual Mode Switch Circuit TCM monitors manual mode,
non manual mode, up or down
switch signal, and detects as ir-
regular when impossible input
pattern occurs 2 second or
more. Harness or connectors
(These switches circuit is
open or shorted.)
 Manual mode switch
SLCT LVR POSI : D
MANU MODE SW : ON
A/T shift selector vehicle side harness connector
Voltage (Approx.)
Connector Te r m i n a l
+ −
M57 1
4 Battery voltage
2
3
5
Revision: 2010 May2011 QX56

P2713 PRESSURE CONTROL SOLENOID DTM-147
< DTC/CIRCUIT DIAGNOSIS > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
P2713 PRESSURE CONTROL SOLENOID D
DTC LogicINFOID:0000000006226867
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” is previously c onducted, always turn ignition switch OFF and wait at
least 10 seconds before performing the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT-III
1. Start the engine.
2. Select “BATTERY VOLT”, “MANU MODE SW”, “GEAR” and “VHCL/S SE-A/T” in “Data Monitor” in
“TRANSMISSION”.
3. Drive the vehicle and maintain the following conditions for 5 seconds or more.
4. Perform “Self Diagnostic Resu lts” in “TRANSMISSION”.
With GST
Follow the procedure “With CONSULT-III”.
Is
“P2713” detected?
YES >> Go to TM-147, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006226868
1.CHECK INTERMITTENT INCIDENT
Refer to GI-40, "
Intermittent Incident".
Is the inspection result normal?
YES >> Replace the control valve & TCM. Refer to TM-208, "4WD : Exploded View".
NO >> Repair or replace damaged parts.
DTC Trouble diagnosis name DTC is detected if... Possible cause
P2713 Pressure Control Solenoid D The high and low reverse clutch
solenoid valve monitor value is
0.4 A or less when the high and
low reverse clutch solenoid
valve command value is more
than 0.75 A. Harness or connectors
(Solenoid valve circuit is
open or shorted.)
 High and low reverse clutch solenoid valve
BATTERY VOLT : 9 V or more
MANU MODE SW : ON
GEAR : 3rd
VHCL/S SE-A/T : 10 km/h (7 MPH) or more
Revision: 2010 May2011 QX56

TM-148
< DTC/CIRCUIT DIAGNOSIS >[7AT: RE7R01B]
P2722 PRESSURE CONTROL SOLENOID E
P2722 PRESSURE CONTROL SOLENOID E
DTC LogicINFOID:0000000006226869
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” is previously c onducted, always turn ignition switch OFF and wait at
least 10 seconds before performing the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT-III
1. Start the engine.
2. Select “BATTERY VOLT”, “MANU MODE SW”, “G EAR” and “VHCL/S SE-A/T” in “Data Monitor” in
“TRANSMISSION”.
3. Drive vehicle and maintain the following conditions for 5 seconds or more.
4. Perform “Self Diagnostic Results” in “TRANSMISSION”.
With GST
Follow the procedure “With CONSULT-III”.
Is
“P2722” detected?
YES >> Go to TM-148, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006226870
1.CHECK INTERMITTENT INCIDENT
Refer to GI-40, "
Intermittent Incident".
Is the inspection result normal?
YES >> Replace the control valve & TCM. Refer to TM-208, "4WD : Exploded View".
NO >> Repair or replace damaged parts.
DTC Trouble diagnosis name DTC is detected if... Possible cause
P2722 Pressure Control Solenoid E The low brake solenoid valve
monitor value is 0.4 A or less
when the low brake solenoid
valve command value is more
than 0.75 A. Harness or connectors
(Solenoid valve circuit is
open or shorted.)
 Low brake solenoid valve
BATTERY VOLT : 9 V or more
MANU MODE SW : ON
GEAR : 1st
VHCL/S SE-A/T : 10 km/h (7 MPH) or more
Revision: 2010 May2011 QX56

P2731 PRESSURE CONTROL SOLENOID FTM-149
< DTC/CIRCUIT DIAGNOSIS > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
P2731 PRESSURE CONTROL SOLENOID F
DTC LogicINFOID:0000000006226871
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” is previously c onducted, always turn ignition switch OFF and wait at
least 10 seconds before performing the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT-III
1. Start the engine.
2. Select “BATTERY VOLT”, “MANU MODE SW”, “GEAR” and “VHCL/S SE-A/T” in “Data Monitor” in
“TRANSMISSION”.
3. Drive vehicle and maintain the following conditions for 5 seconds or more.
4. Perform “Self Diagnostic Resu lts” in “TRANSMISSION”.
With GST
Follow the procedure “With CONSULT-III”.
Is
“P2731” detected?
YES >> Go to TM-149, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006226872
1.CHECK INTERMITTENT INCIDENT
Refer to GI-40, "
Intermittent Incident".
Is the inspection result normal?
YES >> Replace the control valve & TCM. Refer to TM-182, "Exploded View".
NO >> Repair or replace damaged parts.
DTC Trouble diagnosis name DTC is detected if... Possible cause
P2731 Pressure Control Solenoid F The 2346 brake solenoid valve
monitor value is 0.4 A or less
when the 2346 brake solenoid
valve command value is more
than 0.75 A. Harness or connectors
(Solenoid valve circuit is
open or shorted.)
 2346 brake solenoid valve
BATTERY VOLT : 9 V or more
MANU MODE SW : ON
GEAR : 2nd
VHCL/S SE-A/T : 10 km/h (7 MPH) or more
Revision: 2010 May2011 QX56

TM-150
< DTC/CIRCUIT DIAGNOSIS >[7AT: RE7R01B]
P2807 PRESSURE CO
NTROL SOLENOID G
P2807 PRESSURE CONTROL SOLENOID G
DTC LogicINFOID:0000000006226873
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” is previously c onducted, always turn ignition switch OFF and wait at
least 10 seconds before performing the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT-III
1. Start the engine.
2. Select “BATTERY VOLT”, “MANU MODE SW”, “G EAR” and “VHCL/S SE-A/T” in “Data Monitor” in
“TRANSMISSION”.
3. Drive vehicle and maintain the following conditions for 5 seconds or more.
4. Perform “Self Diagnostic Results” in “TRANSMISSION”.
With GST
Follow the procedure “With CONSULT-III”.
Is
“P2807” detected?
YES >> Go to TM-150, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006226874
1.CHECK INTERMITTENT INCIDENT
Refer to GI-40, "
Intermittent Incident".
Is the inspection result normal?
YES >> Replace the control valve & TCM. Refer to TM-208, "4WD : Exploded View".
NO >> Repair or replace damaged parts.
DTC Trouble diagnosis name DTC is detected is... Possible cause
P2807 Pressure Control Solenoid G The direct clutch solenoid valve
monitor value is 0.4 A or less
when the direct clutch solenoid
valve command value is more
than 0.75 A. Harness or connectors
(Solenoid valve circuit is
open or shorted.)
 Direct clutch solenoid valve
BATTERY VOLT : 9 V or more
MANU MODE SW : ON
GEAR : 1st
VHCL/S SE-A/T : 10 km/h (7 MPH) or more
Revision: 2010 May2011 QX56

TOW MODE SYSTEMTM-153
< DTC/CIRCUIT DIAGNOSIS > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
TOW MODE SYSTEM
Component Function CheckINFOID:0000000006226876
1.CHECK TOW MODE INDICATOR LAMP FUNCTION
1. Turn ignition switch ON.
2. Check that tow mode indicator lamp turn s ON/OFF when tow mode switch is operated.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Go to TM-153, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000006226877
NOTE:
Tow mode switch is integrated in to SNOW MODE/T OW MODE/VDC OFF switch assembly (2WD models) or
4WD switch assembly (4WD models).
1.CHECK DTC OF TCM
With CONSULT-III
1. Turn ignition switch ON.
2. Perform “Self-Diagnostic Results” in “TRANSMISSION”.
Is any DTC detected?
YES >> Check DTC detect ed item. Refer to TM-78, "DTC Index".
NO >> GO TO 2.
2.CHECK DTC OF COMBINATION METER
With CONSULT-III
Perform “Self-Diagnostic Re sults” in “METER/M&A”.
Is any DTC detected?
YES >> Check DTC detect ed item. Refer to MWI-43, "DTC Index".
NO >> GO TO 3.
3.CHECK COMBINATION METER
With CONSULT-III
1. Select “TOW MODE IND” in “Data Monitor” in “METER/M&A”.
2. Check that “TOW MODE IND” turns ON/OFF when tow mode switch is operated.
Is the inspection result normal?
YES >> Replace combination meter. Refer to MWI-85, "Exploded View".
NO >> GO TO 4.
4.CHECK TOW MODE SWITCH SIGNAL
With CONSULT-III
1. Select “TOW MODE SW” in “Data Monitor” in “TRANSMISSION”.
2. Check that “TOW MODE SW” turns ON /OFF when tow mode switch is operated.
Is the inspection result normal?
YES >> Replace combination meter. Refer to MWI-85, "Exploded View".
NO >> GO TO 5.
5.CHECK TOW MODE SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect SNOW MODE/TOW MODE/VDC OFF switch assembly (2WD models) or 4WD switch assem-
bly connector (4WD models).
3. Turn ignition switch ON.
4. Check voltage between SNOW MODE/TOW MODE/VDC OFF switch assembly (2WD models) or 4WD
switch assembly connector (4WD models) vehicle side harness connector terminals.
Revision: 2010 May2011 QX56

TM-156
< DTC/CIRCUIT DIAGNOSIS >[7AT: RE7R01B]
SHIFT POSITION INDICATOR CIRCUIT
SHIFT POSITION INDICATOR CIRCUIT
DescriptionINFOID:0000000006226879
TCM transmits a shift position signal to the combination meter via CAN communication line. While the vehicle
is running, the combination meter displays a shift position in the information display, according to this signal.
Refer to
MWI-9, "
METER SYSTEM : System Diagram".
Component Function CheckINFOID:0000000006226880
1.CHECK A/T INDICATOR
CAUTION:
Always drive vehicle at a safe speed.
1. Start the engine.
2. Check the actual selector lever position (“P”, “R”, “N” and “D”) and the indication of the shift position indi-
cator mutually coincide.
3. Drive vehicle in the manual mode, and then check that the actual gear position and the indication of the
shift position indicator mutually coincide when the sele ctor lever is shifted to “UP (+ side)” or “DOWN (−
side)” side (1GR ⇔ 7GR).
Is the inspection result normal?
YES >> INSPECTION END
NO >> Go to TM-156, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000006226881
1.CHECK INPUT SIGNALS
With CONSULT-III
1. Start the engine.
2. Select “SLCT LVR POSI” in “Data Monitor” in “TRANSMISSION”.
3. Check the actual selector lever position (“P”, “R”, “N” and “D”) and the indication of the “SLCT LVR POSI”
mutually coincide. Refer to TM-68, "
Reference Value".
4. Drive vehicle in the manual mode, and then check that the actual gear position and the indication of the
“SLCT LVR POSI” mutually coincide when the selector lever is shifted to the “UP (+ side)” or “DOWN (−
side)” side (1GR ⇔ 7GR). Refer to TM-68, "
Reference Value".
Is the inspection result normal?
YES >> INSPECTION END
NO-1 [The actual gear position does not change, or sh ifting into the manual mode is not possible (no gear
shifting in the manual mode possible). Or the shift position indicator is not indicated.]>>Check manual
mode switch. Refer to TM-146, "
Component Inspection (Manual Mode Switch)".
 Check A/T main system (Fai l-safe function actuated).
- Perform “Self Diagnostic Results” in “TRANSMISSION”. Refer to TM-78, "
DTC Index".
NO-2 (The actual gear position changes, but the shift pos ition indicator is not indicated.)>>Perform “Self
Diagnostic Results” in “TRANSMISSION”. Refer to TM-78, "
DTC Index".
NO-3 (The actual gear position and the indication on t he shift position indicator do not coincide.)>>Perform
“Self Diagnostic Results” in “TRANSMISSION”. Refer to TM-78, "
DTC Index".
NO-4 (Only a specific position or positions is/are not indicated on the shift position indicator.)>>Check the
combination meter. Refer to MWI-35, "
Reference Value".
Revision: 2010 May2011 QX56