2011 INFINITI QX56 sensor

CCS
C1A01 POWER SUPPLY CIRCUIT 1, C1A02 POWER SUPPLY CIRCUIT 2
CCS-85
< DTC/CIRCUIT DIAGNOSIS > [ICC]
C
D
E
F
G H
I
J
K L
M B
N P A
C1A01 POWER SUPPLY CIRCUIT 1, C1A02 POWER SUPPLY CIRCUIT 2
ADAS CONTROL UNIT
ADAS CONTROL UNIT : DTC LogicINFOID:0000000006227992
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Turn the MAIN switch of ICC system ON.
3. Perform “All DTC Readi ng” with CONSULT-III.
4. Check if the “C1A01” or “C1A02” is detected as t he current malfunction in “Self Diagnostic Result” of “ICC/
ADAS”.
Is
“C1A01” or “C1A02” detected as the current malfunction?
YES >> Refer to CCS-85, "ADAS CONTROL UNIT : Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
ADAS CONTROL UNIT : Diagnosis ProcedureINFOID:0000000006227993
1.CHECK ADAS CONTROL UNIT PO WER SUPPLY AND GROUND CIRCUIT
Check power supply and ground circuit of ADAS control unit. Refer to DAS-62, "
Diagnosis Procedure".
Is the inspection result normal?
YES >> Replace the ADAS control unit. Refer to DAS-63, "Removal and Installation".
NO >> Repair or replace the malfunctioning parts.
ICC SENSOR
ICC SENSOR : DTC LogicINFOID:0000000006224306
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Turn the MAIN switch of ICC system ON.
3. Perform “All DTC Reading” with CONSULT-III.
4. Check if the “C1A01” or “C1A02” is detected as the current malfunction in “Self Diagnostic Result” of
“LASER”.
Is
“C1A01” or “C1A02” detected as the current malfunction?
YES >> Refer to CCS-86, "ICC SENSOR : Diagnosis Procedure".
DTC
(On board dis- play) Trouble diagnosis
name DTC detecting condition Possible causes
C1A01 (1) POWER SUPPLY
CIR The battery voltage sent to ADAS control unit re-
mains less than 7.9 V for 5 seconds
 Connector, harness, fuse
 ADAS control unit
C1A02
(2) POWER SUPPLY
CIR 2 The battery voltage sent to ADAS control unit re-
mains more than 19.3 V for 5 seconds
DTC
Trouble diagnosis
name DTC detecting condition Possible causes
C1A01 POWER SUPPLY
CIR The battery voltage sent to ICC sensor remains
less than 7.9 V for 5 seconds
 Connector, harness, fuse
 ICC sensor
C1A02 POWER SUPPLY
CIR 2 The battery voltage sent to ICC sensor remains
more than 19.3 V for 5 seconds
Revision: 2010 May2011 QX56

CCS-86
< DTC/CIRCUIT DIAGNOSIS >[ICC]
C1A01 POWER SUPPLY CIRCUIT 1,
C1A02 POWER SUPPLY CIRCUIT 2
NO >> Refer to GI-40, "Intermittent Incident".
ICC SENSOR : Diagnosis ProcedureINFOID:0000000006224307
1.CHECK ICC SENSOR POWER SUPPLY AND GROUND CIRCUIT
Check power supply and ground circuit of ICC sensor. Refer to CCS-158, "
ICC SENSOR : Diagnosis Proce-
dure".
Is the inspection result normal?
YES >> Replace the ICC sensor. Refer to CCS-176, "Exploded View".
NO >> Repair or replace the malfunctioning parts.
Revision: 2010 May2011 QX56

CCS
C1A03 VEHICLE SPEED SENSORCCS-87
< DTC/CIRCUIT DIAGNOSIS > [ICC]
C
D
E
F
G H
I
J
K L
M B
N P A
C1A03 VEHICLE SPEED SENSOR
DTC LogicINFOID:0000000006224308
DTC DETECTION LOGIC
NOTE:
If DTC “C1A03” is detected along with DTC “U1000” or “C1A04”, first diagnose the DTC “U1000” or “C1A04”.
 Refer to CCS-145, "
ADAS CONTROL UNIT : DTC Logic" for DTC “U1000”.
 Refer to CCS-89, "
DTC Logic" for DTC “C1A04”.
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Turn the MAIN switch of ICC system ON.
3. Drive the vehicle at 30 km/h (19 MPH) or more. CAUTION:
Always drive safely.
4. Stop the vehicle.
5. Perform “All DTC Readi ng” with CONSULT-III.
6. Check if the “C1A03” is detected as the current malfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“C1A03” detected as the current malfunction?
YES >> Refer to CCS-87, "Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000006224309
1.CHECK SELF-DIAGNOSIS RESULTS
Check if “C1A04” or “U1000” is detected other than “C1A03” in “Self Diagnostic Result” of “ICC/ADAS”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
CCS-50, "
DTC Index".
NO >> GO TO 2.
2.CHECK DATA MONITOR
1. Start the engine.
2. Drive the vehicle.
3. Check that the value of “VHCL SPD AT” is almost the same as the value of “VHCL SPEED SE” in “DATA
MONITOR” of “ICC/ADAS”.
CAUTION:
Be careful of the vehicle speed.
Is the inspection result normal?
YES >> Replace the ADAS control unit. Refer to DAS-63, "Removal and Installation".
NO >> GO TO 3.
3.CHECK TCM SELF-DIAGNOSIS RESULTS
1. Perform “All DTC Reading”.
2. Check if any DTC is detected in “Sel f Diagnostic Result” of “TRANSMISSION”.
DTC
(On board
display) Trouble diagnosis
name DTC detecting condition Possible causes
C1A03 (3) VHCL SPEED SE
CIRC If the vehicle speed signal (wheel speed) from
ABS actuator and electric unit (control unit) and
the A/T vehicle speed sensor signal (output
shaft revolution signal) from TCM, received by
the ADAS control unit via CAN communication,
are inconsistent  Wheel speed sensor
 ABS actuator and electric unit (control
unit)
 Vehicle speed sensor A/T (output speed sensor)
TCM
 ADAS control unit
Revision: 2010 May2011 QX56

CCS-88
< DTC/CIRCUIT DIAGNOSIS >[ICC]
C1A03 VEHICLE SPEED SENSOR
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair
or replace the malfunctioning parts. Refer to
TM-78, "
DTC Index".
NO >> GO TO 4.
4.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF-DIAGNOSIS RESULTS
Check if any DTC is detected in “Self Diagnostic Result” of “ABS”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
BRC-51, "
DTC Index".
NO >> Replace the ADAS control unit. Refer to DAS-63, "
Removal and Installation".
Revision: 2010 May2011 QX56

CCS-96
< DTC/CIRCUIT DIAGNOSIS >[ICC]
C1A12 LASER BEAM OFF CENTER
C1A12 LASER BEAM OFF CENTER
ADAS CONTROL UNIT
ADAS CONTROL UNIT : DTC LogicINFOID:0000000006224319
DTC DETECTION LOGIC
ADAS CONTROL UNIT : Diagnosis ProcedureINFOID:0000000006224320
1.CHECK ICC SENSOR SELF-DIAGNOSIS RESULTS
1. Perform “All DTC Reading” with CONSULT-III.
2. Check if the “C1A12” is detected as the current malfunction in “Self Diagnostic Result” of “LASER”.
Is
“C1A12” detected?
YES >> Refer to CCS-96, "ICC SENSOR : DTC Logic".
NO >> GO TO 2.
2.CHECK ADAS CONTROL SELF-DIAGNOSIS RESULTS
Check if the “C1A12” is detected as the current malfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“C1A12” detected?
YES >> Replace ADAS control unit. Refer to DAS-63, "Removal and Installation".
NO >> INSPECTION END
ICC SENSOR
ICC SENSOR : DTC LogicINFOID:0000000006224321
DTC DETECTION LOGIC
ICC SENSOR : Diagnosis ProcedureINFOID:0000000006224322
1.ADJUST LASER BEAM AIMING
1. Adjust the laser beam aiming with CONSULT-III. Refer to CCS-72, "
Description".
2. Perform “All DTC Reading”.
3. Check if the “C1A12” is detected in “Self Diagnostic Result” of “LASER”.
Is
“C1A12” detected?
YES >> Replace ICC sensor. Refer to CCS-176, "Exploded View".
NO >> INSPECTION END
DTC
(On board dis- play) Trouble diagnosis name DTC detecting condition Possible causes
C1A12 (12) LASER BEAM OFFCNTR Laser beam of ICC sensor is off the aiming
point
Laser beam is off the aiming point
DTC Trouble diagnosis name DTC detecting condition Possible causes
C1A12 LASER BEAM OFFCNTR Laser beam of ICC sensor is off the aiming
point Laser beam is off the aiming point
Revision: 2010 May2011 QX56

CCS
C1A13 STOP LAMP RELAYCCS-97
< DTC/CIRCUIT DIAGNOSIS > [ICC]
C
D
E
F
G H
I
J
K L
M B
N P A
C1A13 STOP LAMP RELAY
DTC LogicINFOID:0000000006224323
DTC DETECTION LOGIC
NOTE:
If DTC “C1A13” is detected along with DTC “U 1000”, first diagnose the DTC “U1000”. Refer to CCS-145,
"ADAS CONTROL UNIT : DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE (1)
1. Start the engine.
2. Perform the active test item “STOP LAMP” with CONSULT-III.
3. Perform “All DTC Reading”.
4. Check if the “C1A13” is detected as the current malfunction in the “Self Diagnostic Result” of “ICC/ADAS”.
Is
“C1A13” detected as the current malfunction?
YES >> Refer to CCS-97, "Diagnosis Procedure".
NO >> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE (2)
1. Drive at the vehicle speed of 40 km/h (25 MPH) or more for approximately 60 seconds or more without the
brake pedal depressed.
CAUTION:
Always drive safely.
NOTE:
If it is outside the above condition, repeat step 1.
2. Perform “All DTC Reading”.
3. Check if the “C1A13” is detected as the current malfunction in the “Self Diagnostic Result” of “ICC/ADAS”.
Is
“C1A13” detected as the current malfunction?
YES >> Refer to CCS-97, "Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000006224324
1.CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected other than “C1A13” in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1000” detected?
YES >> Perform the CAN communicati on system inspection. Repair or replace the malfunctioning parts.
Refer to CCS-145, "
ADAS CONTROL UNIT : DTC Logic".
NO >> GO TO 2.
2.CHECK STOP LAMP SWITCH
Check that “STOP LAMP SW” operate normally in “DATA MONITOR” of “ICC/ADAS”.
DTC
(On board dis-
play) Trouble diagnosis name DTC detecting condition Possible causes
C1A13 (13) STOP LAMP RLY FIX  Stop lamp inactive state continues for 0.3
seconds or more despite the outputting of
an ICC sensor ICC brake hold relay drive
signal
 The stop lamp remains ON for 60 seconds or more under the following conditions:
- Driving at 40 km/h or more
- No stop lamp drive signal output from ICC
sensor
- No brake operation  Stop lamp switch circuit
 ICC brake switch circuit
 ICC brake hold relay circuit
 Stop lamp switch
 ICC brake switch
 ICC brake hold relay
 Incorrect stop lamp switch installation
 Incorrect ICC brake switch installation
ECM
 ABS actuator and elec
tric unit (control
unit)
Revision: 2010 May2011 QX56

CCS
C1A14 ECMCCS-103
< DTC/CIRCUIT DIAGNOSIS > [ICC]
C
D
E
F
G H
I
J
K L
M B
N P A
C1A14 ECM
DTC LogicINFOID:0000000006224326
DTC DETECTION LOGIC
NOTE:
If DTC “C1A14” is detected along with DTC “U 1000”, first diagnose the DTC “U1000”. Refer to CCS-145,
"ADAS CONTROL UNIT : DTC Logic".
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Operate the ICC system and drive. CAUTION:
Always drive safely.
3. Stop the vehicle.
4. Perform “All DTC Readi ng” with CONSULT-III.
5. Check if the “C1A14” is detected as the current malfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“C1A14” detected as the current malfunction?
YES >> Refer to CCS-103, "Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000006224327
1.CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected other than “C1A14” in “Self Diagnostic Result” of “ICC/ADAS”.
Is
“U1000” detected?
YES >> Perform the CAN communicati on system inspection. Repair or replace the malfunctioning parts.
Refer to CCS-145, "
ADAS CONTROL UNIT : DTC Logic".
NO >> GO TO 2.
2.PERFORM SELF-DIAGNOSIS OF ECM
Check if any DTC is detected in “S elf Diagnostic Result” of “ENGINE”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
EC-98, "
DTC Index".
NO >> Replace the ADAS control unit. Refer to DAS-63, "
Removal and Installation".
DTC
(On board dis-
play) Trouble diagnosis name DTC detecting condition Possible causes
C1A14 (14) ECM CIRCUIT If ECM is malfunctioning  Accelerator pedal position sensor
ECM
 ADAS control unit
Revision: 2010 May2011 QX56

CCS-104
< DTC/CIRCUIT DIAGNOSIS >[ICC]
C1A15 GEAR POSITION
C1A15 GEAR POSITION
DescriptionINFOID:0000000006224328
ADAS control unit judges the gear pos
ition based on the following signals.
 Current gear position signal transmitt ed from TCM via CAN communication.
 Value of gear ratio calculated from input speed signal transmitted from TCM via CAN communication.
 Value of gear ratio calculated from the vehicle speed signal transmitted from ABS actuator and electric unit
(control unit) via CAN communication.
DTC LogicINFOID:0000000006224329
DTC DETECTION LOGIC
NOTE:
If DTC “C1A15” is detected along with DTC “U1000”, “C1A03”, or “C1A04”, first diagnose the DTC “U1000”,
“C1A03”, or “C1A04”.
 Refer to CCS-145, "
ADAS CONTROL UNIT : DTC Logic" for DTC “U1000”.
 Refer to CCS-87, "
DTC Logic" for DTC “C1A03”.
 Refer to CCS-89, "
DTC Logic" for DTC “C1A04”.
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine.
2. Turn the MAIN switch of ICC system ON.
3. Drive the vehicle at 10 km/h (6 MPH) or faster for approximately 15 minutes or more.
CAUTION:
Always drive safely.
4. Stop the vehicle.
5. Perform “All DTC Reading” with CONSULT-III.
6. Check if “C1A15” is detected as the current malf unction in the “Self Diagnostic Result” of “ICC/ADAS”.
Is
“C1A15” detected as the current malfunction?
YES >> Refer to CCS-104, "Diagnosis Procedure".
NO >> Refer to GI-40, "
Intermittent Incident".
Diagnosis ProcedureINFOID:0000000006224330
1.CHECK SELF-DIAGNOSIS RESULTS
Check if “C1A03”, “C1A04”, or “U1000” is detected ot her than “C1A15” in “Self Diagnostic Result” of “ICC/
ADAS”.
Is any DTC detected?
YES >> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
CCS-50, "
DTC Index".
NO >> GO TO 2.
2.CHECK VEHICLE SPEED SIGNAL
Check that “VHCL SPEED SE” operates norma lly in “DATA MONITOR” of “ICC/ADAS”.
CAUTION:
Be careful of the vehicle speed.
Is the inspection result normal?
DTC
(On board dis- play) Trouble diagnosis
name DTC detecting condition Possible causes
C1A15 (15) GEAR POSITION A mismatch between an current gear posi-
tion signal transmitted from TCM via CAN
communication and a gear position calculat-
ed by the ADAS control unit continues for
approximately 11 minutes or more  Input speed sensor
 Vehicle speed sensor A/T (output speed
sensor)
TCM
Revision: 2010 May2011 QX56