2011 INFINITI QX56 Wiring

DAS-272
< PRECAUTION >[LDW & LDP]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint S
ystem (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000006223697
The Supplemental Restraint System such as “A IR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severi ty of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and w hether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
 To avoid rendering the SRS inopera tive, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISS AN/INFINITI dealer.
 Improper maintenance, including in correct removal and installation of the SRS, can lead to personal
injury caused by unintent ional activation of the system. For re moval of Spiral Cable and Air Bag
Module, see the “SRS AIR BAG”.
 Do not use electrical test equipmen t on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identi fied by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
 When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s)
with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly
causing serious injury.
 When using air or electric power tools or hammers , always switch the ignition OFF, disconnect the
battery, and wait at least 3 minu tes before performing any service.
Precautions For Harness RepairINFOID:0000000006223698
ITS communication uses a twisted pair line. Be careful when repairing it.
 Solder the repaired area and wrap tape around the soldered area.
NOTE:
A fray of twisted lines must be within 110 mm (4.33 in).
SKIB8766E
Revision: 2010 May2011 QX56

DAS
DRIVER ASSISTANCE SYSTEMSDAS-317
< WIRING DIAGRAM > [LDW & LDP]
C
D
E
F
G H
I
J
K L
M B
N P A
WIRING DIAGRAM
DRIVER ASSISTANCE SYSTEMS
Wiring DiagramINFOID:0000000006223726
JCOWM0352GB
Revision: 2010 May2011 QX56

DAS-318
< WIRING DIAGRAM >[LDW & LDP]
DRIVER ASSISTANCE SYSTEMS
JCOWM0353GB
Revision: 2010 May2011 QX56

DAS
DRIVER ASSISTANCE SYSTEMSDAS-319
< WIRING DIAGRAM > [LDW & LDP]
C
D
E
F
G H
I
J
K L
M B
N P A
JCOWM0354GB
Revision: 2010 May2011 QX56

DAS-320
< WIRING DIAGRAM >[LDW & LDP]
DRIVER ASSISTANCE SYSTEMS
JCOWM0355GB
Revision: 2010 May2011 QX56

DAS
DRIVER ASSISTANCE SYSTEMSDAS-321
< WIRING DIAGRAM > [LDW & LDP]
C
D
E
F
G H
I
J
K L
M B
N P A
JCOWM0356GB
Revision: 2010 May2011 QX56

DAS-322
< WIRING DIAGRAM >[LDW & LDP]
DRIVER ASSISTANCE SYSTEMS
JCOWM0357GB
Revision: 2010 May2011 QX56

DAS
DRIVER ASSISTANCE SYSTEMSDAS-323
< WIRING DIAGRAM > [LDW & LDP]
C
D
E
F
G H
I
J
K L
M B
N P A
JCOWM0358GB
Revision: 2010 May2011 QX56