2011 INFINITI QX56 turn signal

ADP-62
< DTC/CIRCUIT DIAGNOSIS >
B2116 TILT MOTOR
B2116 TILT MOTOR
DTC LogicINFOID:0000000006248346
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.STEP 1
Turn ignition switch ON.
>> GO TO 2.
2.STEP 2
Check “Self diagnostic result” with CONSULT-III.
Is the DTC detected?
YES >> Perform diagnosis procedure. Refer to ADP-62, "DiagnosisProcedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006248347
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Check “Self diagnostic result” with CONSULT-III.
3. Erase the DTC.
4. Perform DTC confirmation procedure. Refer to ADP-62, "
DTC Logic".
Is the DTC displayed again?
YES >> GO TO 2.
NO >> Check intermittent incident. Refer to GI-40, "
Intermittent Incident".
2.CHECK TILT MOTOR CIRCUIT (POWER SHORT)
1. Turn ignition switch OFF.
2. Disconnect automatic drive positioner control unit and tilt motor connector.
3. Check voltage between tilt motor harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness or connector.
3.CHECK AUTOMATIC DRIVER POSITION ER CONROL UNIT OUTPUT SIGNAL
1. Connect automatic drive positioner control unit connector.
2. Check voltage between automatic drive posit ioner control unit harness connector and ground.
DTC No.Trouble diagnosis
name DTC detecting condition Possible cause
B2116 STEERING TILT The automatic drive positioner control unit detects
the output of tilt motor output terminal for 0.1 second
or more even if the tilt switch is not input.  Automatic drive positioner con-
trol unit
 Tilt motor harn ess is shorted
(+)
(-)Voltage (V)
(Approx.)
Tilt motor
Connector Terminals
M116 1
Ground 0
2
Revision: 2010 May2011 QX56

ADP-64
< DTC/CIRCUIT DIAGNOSIS >
B2128 UART COMMUNICATION LINE
B2128 UART COMMUNICATION LINE
DescriptionINFOID:0000000006248348
Driver seat control unit performs UART communication with the automatic drive positioner control unit using 1
communication lines. Driver seat control unit receives t he operation signals of tilt & telescopic switch, door mir-
ror remote control switch, and the position signals of door mirror sensor from the automatic drive positioner
control unit and transmits the operation request signal.
DTC LogicINFOID:0000000006248349
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.STEP 1
Turn ignition switch ON.
>> GO TO 2.
2.PROCEDURE
Check “Self diagnostic result” with CONSULT-III.
Is the DTC detected?
YES >> Perform diagnosis procedure. Refer to ADP-64, "DiagnosisProcedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006248350
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Check “Self diagnostic result” with CONSULT-III.
3. Erase the DTC.
4. Perform DTC confirmation procedure. Refer to ADP-62, "
DTC Logic".
Is the DTC displayed again?
YES >> GO TO 2.
NO >> Check intermittent incident. Refer to GI-40, "
Intermittent Incident".
2.CHECK UART COMMUNICATION LINE CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect driver seat control unit and autom atic drive positioner control unit connector.
3. Check continuity between driver seat control uni t harness connector and automatic drive positioner con-
trol unit harness connector.
4. Check continuity between driver seat control unit harness connector and ground.
DTC No. Trouble diagnosis name DTC detecting condition Possible cause B2128 UART COMM The communication between driver seat control unit
and auto drive positioner control unit is interrupted for
a period of time.  UART communication line
(UART communication line is
open or shorted)
 Driver seat control unit
 Automatic drive positioner
control unit
Driver seat control unit Automatic drive positioner control unit Continuity
Connector Terminal Connector Terminal
B452 2 M75 8 Existed
Revision: 2010 May2011 QX56

POWER SUPPLY AND GROUND CIRCUITADP-67
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
POWER SUPPLY AND GROUND CIRCUIT
DRIVER SEAT CONTROL UNIT
DRIVER SEAT CONTROL UNIT : Diagnosis ProcedureINFOID:0000000006248353
1.CHECK FUSE
Check that the following fuse and fusible link are not fusing.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace the blown fuse after repairing the affected circuit.
2.CHECK DRIVER SEAT CONTROL UNIT POWER SUPPLY
1. Turn ignition switch OFF.
2. Disconnect driver seat control unit connector.
3. Check voltage between driver seat control unit harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness.
3.CHECK DRIVER SEAT CONTROL UNIT GROUND CIRCUIT
Check continuity between the driver s eat control unit harness connector and ground.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Repair or replace harness.
DRIVER SEAT CONTROL UNIT : Special Repair RequirementINFOID:0000000006248354
1.PERFORM ADDITIONAL SERVICE
Perform additional service when removing battery negative terminal.
>> Refer to ADP-51, "
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMI-
NAL : Description".
AUTOMATIC DRIVE POSITIONER CONTROL UNIT
AUTOMATIC DRIVE POSITIONER CO NTROL UNIT : Diagnosis Procedure
INFOID:0000000006248355
NOTE:
Do not disconnect the battery negative terminal and the dr iver seat control unit connector until DTC is con-
firmed with CONSULT-III.
1.CHECK FUSE
Check that the following fuse and fusible link are not fusing.
Signal name Fuse No.
Battery power supply K (50 A)
(+) (-)Voltage (V)
(Approx.)
Driver seat control unit
Connector Terminals B451 33 Ground Battery voltage
Driver seat control unit GroundContinuity
Connector Terminal
B451 43 Existed
Revision: 2010 May2011 QX56

ADP-68
< DTC/CIRCUIT DIAGNOSIS >
POWER SUPPLY AND GROUND CIRCUIT
Is the inspection result normal?
YES >> GO TO 2.
NO >> Replace the blown fuse after repairing the affected circuit.
2.CHECK AUTOMATIC DRIVE POSITIONER CONTROL UNIT POWER SUPPLY
1. Turn ignition switch OFF.
2. Disconnect automatic drive positioner control unit connector.
3. Check voltage between automatic drive posit ioner control unit harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness.
3.CHECK AUTOMATIC DRIVE POSITION ER CONTROL UNIT GROUND CIRCUIT
Check continuity between the automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Repair or replace harness.
AUTOMATIC DRIVE POSITIONER CONTROL UNIT : Special Repair Requirement
INFOID:0000000006248356
1.PERFORM ADDITIONAL SERVICE
Perform additional service when removing battery negative terminal.
>> Refer to ADP-51, "
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMI-
NAL : Description".
Signal name Fuse No.
Battery power supply K (50 A)
(+) (-)Voltage (V)
(Approx.)
Automatic drive positioner control unit
Connector Terminals M104 25 Ground Battery voltage
Automatic drive positioner control unit GroundContinuity
Connector Terminal
M104 30 Existed
Revision: 2010 May2011 QX56

SLIDING SWITCHADP-69
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
SLIDING SWITCH
Component Function CheckINFOID:0000000006248357
1.CHECK FUNCTION
1. Select “SLIDE SW-FR”, “SLIDE SW-RR” in “Data monitor” mode with CONSULT-III.
2. Check sliding switch signal under the following conditions.
Is the indication normal?
YES >> INSPECTION END
NO >> Perform diagnosis procedure. Refer to ADP-69, "
DiagnosisProcedure".
Diagnosis ProcedureINFOID:0000000006248358
1.CHECK SLIDING SWITCH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect power seat switch connector.
3. Turn ignition switch ON.
4. Check voltage between power seat switch harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK SLIDING SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect driver seat control unit connector.
3. Check continuity between driver seat control uni t harness connector and power seat switch harness con-
nector.
4. Check continuity between driver s eat control unit harness connector and ground.
Is the inspection result normal?
YES >> Replace driver seat control unit.
Monitor item Condition Status
SLIDE SW-FR Sliding switch (forward) Operate ON
Release OFF
SLIDE SW-RR Sliding switch (backward) Operate ON
Release OFF
(+)
(-)Voltage (V)
(Approx.)
Power seat switch
Connector Terminals
B459 8
Ground 12
24
Driver seat control unit Power seat switch Continuity
Connector Terminal Connector Terminal
B452 8
B459 8
Existed
24 24
Driver seat control unit GroundContinuity
Connector Terminal
B452 8
Not existed
24
Revision: 2010 May2011 QX56

RECLINING SWITCHADP-71
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
RECLINING SWITCH
Component Function CheckINFOID:0000000006248360
1.CHECK FUNCTION
1. Select “RECLN SW-FR”, “RECLN SW-RR” in “Data monitor” mode with CONSULT-III.
2. Check reclining switch signal under the following conditions.
Is the indication normal?
YES >> INSPECTION END
NO >> Perform diagnosis procedure. Refer to ADP-71, "
DiagnosisProcedure".
Diagnosis ProcedureINFOID:0000000006248361
1.CHECK RECLINING SWITCH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect power seat switch connector.
3. Turn ignition switch ON.
4. Check voltage between power seat switch harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK RECLINING SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect driver seat control unit connector.
3. Check continuity between driver seat control uni t harness connector and power seat switch harness con-
nector.
4. Check continuity between driver s eat control unit harness connector and ground.
Is the inspection result normal?
YES >> Replace driver seat control unit.
Monitor item Condition Status
RECLINE SW-FR Reclining switch (forward)Operate ON
Release OFF
RECLINE SW-RR Reclining switch (backward) Operate ON
Release OFF
(+)
(-)Voltage (V)
(Approx.)
Power seat switch
Connector Terminals
B459 9
Ground 12
25
Driver seat control unit Power seat switch Continuity
Connector Terminal Connector Terminal
B452 9
B459 9
Existed
25 25
Driver seat control unit GroundContinuity
Connector Terminal
B452 9
Not existed
25
Revision: 2010 May2011 QX56

LIFTING SWITCH (FRONT)ADP-73
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
LIFTING SWITCH (FRONT)
Component Function CheckINFOID:0000000006248363
1.CHECK FUNCTION
1. Select “LIFT FR SW-UP”, “LIFT FR SW-DN” in “Data monitor” mode with CONSULT-III.
2. Check lifting switch (front) signal under the following conditions.
Is the indication normal?
YES >> INSPECTION END
NO >> Perform diagnosis procedure. Refer to ADP-73, "
DiagnosisProcedure".
Diagnosis ProcedureINFOID:0000000006248364
1.CHECK LIFTING SWITCH (FRONT) INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect power seat switch connector.
3. Turn ignition switch ON.
4. Check voltage between power seat switch harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK LIFTING SWITCH (FRONT) CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect driver seat control unit connector.
3. Check continuity between driver seat control uni t harness connector and power seat switch harness con-
nector.
4. Check continuity between driver s eat control unit harness connector and ground.
Is the inspection result normal?
YES >> Replace driver seat control unit.
Monitor item Condition Status
LIFT FR SW-UP Lifting switch front (up) Operate ON
Release OFF
LIFT FR SW-DN Lifting switch front (down) Operate ON
Release OFF
(+)
(-)Voltage (V)
(Approx.)
Power seat switch
Connector Terminals
B459 10
Ground 12
26
Driver seat control unit Power seat switch Continuity
Connector Terminal Connector Terminal
B452 10
B459 10
Existed
26 26
Driver seat control unit GroundContinuity
Connector Terminal
B452 10
Not existed
26
Revision: 2010 May2011 QX56

LIFTING SWITCH (REAR)ADP-75
< DTC/CIRCUIT DIAGNOSIS >
C
DE
F
G H
I
K L
M A
B
ADP
N
O P
LIFTING SWITCH (REAR)
Component Function CheckINFOID:0000000006248366
1.CHECK FUNCTION
1. Select “LIFT RR SW-UP”, “LIFT RR SW-DN” in “Data monitor” mode with CONSULT-III.
2. Check lifting switch (rear) signal under the following conditions.
Is the indication normal?
YES >> INSPECTION END
NO >> Perform diagnosis procedure. Refer to ADP-75, "
DiagnosisProcedure".
Diagnosis ProcedureINFOID:0000000006248367
1.CHECK LIFTING SWITCH (REAR) INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect power seat switch connector.
3. Turn ignition switch ON.
4. Check voltage between power seat switch harness connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK LIFTING SWITCH (REAR) CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect driver seat control unit connector.
3. Check continuity between driver seat control uni t harness connector and power seat switch harness con-
nector.
4. Check continuity between driver s eat control unit harness connector and ground.
Is the inspection result normal?
YES >> Replace driver seat control unit.
Monitor item Condition Status
LIFT RR SW-UP Lifting switch rear (up) Operate ON
Release OFF
LIFT RR SW-DN Lifting switch rear (down) Operate ON
Release OFF
(+)
(-)Voltage (V)
(Approx.)
Power seat switch
Connector Terminals
B459 11
Ground 12
27
Driver seat control unit Power seat switch Continuity
Connector Terminal Connector Terminal
B452 11
B459 11
Existed
27 27
Driver seat control unit GroundContinuity
Connector Terminal
B452 11
Not existed
27
Revision: 2010 May2011 QX56