2011 INFINITI QX56 headrest

AV-36
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
Unfinished configurationThe writing of configuration data is incom-
plete.Write configuration data with CONSULT-III.
USB Controller Communication Error USB connection malfunction is detected. Check that the connection to the USB con-
nector is normal.
DVD Mechanism Communication Error AV control unit malfunction is detected.  If DVD can be played, then there is a
possibility of the detection of a temporary
malfunction.
 Replace the AV control unit if the mal- function occurs constantly.
Refer to AV- 2 1 2 , "
Removal and Installa-
tion".
Steer. Angle Sensor Calibration Predictive course line center position ad-
justment of the steering angle sensor is in-
complete.Adjust the predictive course line center po-
sition of the steering angle sensor.
Refer to
AV- 3 9 , "
CONSULT-III Function".
Front Display Connection Error When either one of the following items are
detected:
 front display unit power supply and
ground circuits are malfunctioning.
 Serial communication circuits between AV control unit and front display unit are
malfunctioning.  Front display unit power supply and
ground circuits.
 Serial communication circuits between AV control unit and front display unit.
 AV COMM CIRCUIT
 2nd Display Co nnection Error When either one of the following items are
detected:
 video distributor power supply and
ground circuits are malfunctioning.
 headrest display unit LH power supply and ground circuits are malfunctioning.
 AV communication circuits between AV
control unit and headrest display unit LH
are malfunctioning.
 location recognition signal circuit be-
tween headrest display unit LH and
ground is malfunctioning.  Video distributor power supply and
ground circuits.
 Headrest display unit LH power supply and ground circuits.
 AV communication circuits between AV control unit and headrest display unit LH.
 Location recognition signal circuit be-
tween headrest display unit LH and
ground.
3rd Display Connection Error When either one of the following items are
detected:
 headrest display unit RH power supply
and ground circuits are malfunctioning.
 AV communication circuits between
headrest display unit LH and headrest
display unit RH are malfunctioning.
 location recognition signal circuit be- tween headrest display unit RH and
ground is malfunctioning.  Headrest display unit RH power supply
and ground circuits.
 AV communication circuits between headrest display unit LH and headrest
display unit RH.
 Location recognition signal circuit be- tween headrest display unit RH and
ground.
AM/FM antenna amplifier short to ground Radio antenna amp. ON signal circuit mal-
function is detected.Radio antenna amp. ON signal circuit be-
tween AV control unit and antenna amp.
AM/FM antenna amplifier open
Ext_Amp_ON output terminal short to
ground BOSE amp. ON signal circuit malfunction is
detected.BOSE amp. ON signal circuit between AV
control unit and BOSE amp.
Ext_Amp_ON output terminal :open
GPS Antenna Error GPS antenna connection malfunction is de-
tected.Check the connection of the GPS antenna
connector.
XM Antenna Connection Error Satellite radio antenna connection malfunc-
tion is detected.
Satellite radio antenna disconnection.
USB electric current Error Detection of overcurrent in USB connector. Check USB harness between the AV con-
trol unit and USB connector.
Error item Description Possible malfunction factor/Action to take
Revision: 2010 May2011 QX56

AV
DIAGNOSIS SYSTEM (AV CONTROL UNIT)AV-41
< SYSTEM DESCRIPTION >
C
DE
F
G H
I
J
K L
M B A
O P
DSP CONN [U121D] AV control unit malfunction is detected. If a disc can be played, then there is a
possibility of the detection of a tempo-
rary malfunction.
 Replace the AV control unit if the mal- function occurs constantly.
Refer to AV- 2 1 2 , "
Removal and Installa-
tion".
DSP COMM [U121E]
DVD COMM [U1227] AV control unit malfunction is detected.  If DVD can be played, then there is a
possibility of the detection of a tempo-
rary malfunction.
 Replace the AV control unit if the mal- function occurs constantly.
Refer to AV- 2 1 2 , "
Removal and Installa-
tion".
CONFIG UNFINISH [U122A] The writing of configuration data is incom-
plete.Write configuration data with CONSULT-
III.
ST ANGLE SEN CALIB [U1232] Predictive course line center position ad-
justment of the steering angle sensor is in-
complete.Adjust the predictive course line center po-
sition of the steering angle sensor.
Refer to
BRC-64, "
Work Procedure".
FRONT DISP CONN [U1243] When either one of the following items are
detected:
 front display unit power supply and
ground circuits are malfunctioning.
 serial communication circuits between
AV control unit and front display unit are
malfunctioning.  Front display unit power supply and
ground circuits.
 Serial communication circuits between AV control unit and front display unit.
GPS ANTENNA CONN [U1244] GPS antenna connection malfunction is
detected.Check the connection of the GPS antenna
connector.
 AV COMM CIRCUIT [U1300]
 VIDEO DIST CONN [U1246] When either one of the following items are
detected:
 video distributor power supply and
ground circuits are malfunctioning.
 headrest display unit LH power supply and ground circuits are malfunctioning.
 AV communication circuits between AV
control unit and headrest display unit LH
are malfunctioning.
 location recognition signal circuit be-
tween headrest display unit LH and
ground is malfunctioning.  Video distributor power supply and
ground circuits.
 Headrest display unit LH power supply
and ground circuits.
 AV communication circuits between AV control unit and headrest display unit
LH.
 Location recognition signal circuit be- tween headrest display unit LH and
ground.
3RD DISP CONN [U125A] When either one of the following items are
detected:
 headrest display unit RH power supply
and ground circuits are malfunctioning.
 AV communication circuits between headrest display unit LH and headrest
display unit RH are malfunctioning.
 location recognition signal circuit be- tween headrest display unit RH and
ground is malfunctioning.  Headrest display unit RH power supply
and ground circuits.
 AV communication circuits between Headrest display unit LH and headrest
display unit RH.
 Location recognition signal circuit be- tween headrest display unit RH and
ground.
XM ANTENNA CONN [U1258] Satellite radio antenna connection mal-
function is detected.Satellite radio antenna disconnection.
USB OVERCURRENT [U1263] Detection of overcurrent in USB connect-
er.Check USB harness between the AV con-
trol unit and USB connector.
ANTENNA AMP TERMINAL
[OPEN or SHORT]
[U1264] Radio antenna amp. ON signal circuit mal-
function is detected.
Radio antenna amp. ON signal circuit be-
tween AV control unit and antenna amp.
AMP ON TERMINAL
[GND-SHORT or VB-SHORT]
[U1265] BOSE amp. ON signal circuit malfunction
is detected.
BOSE amp. ON signal circuit between AV
control unit and BOSE amp.
Error item Description Possible malfunction factor/Action to take
Revision: 2010 May2011 QX56

AV
DIAGNOSIS SYSTEM (HEADREST DISPLAY UNIT)AV-49
< SYSTEM DESCRIPTION >
C
DE
F
G H
I
J
K L
M B A
O P
DIAGNOSIS SYSTEM (HEA DREST DISPLAY UNIT)
DescriptionINFOID:0000000006216223
Self-diagnosis of headrest display unit can be perform ed by operating rear seat remote controller.
On Board Diagnosis FunctionINFOID:0000000006216224
Self-diagnosis mode can check the following items.
METHOD OF STARTING
1. Turn ignition switch to the ON position.
2. Turn the headrest display unit OFF.
3. Press each switch of rear seat remote controller in the order shown below.
“AUX(L)” →“VOL DOWN” →“DISP(R)” →“VOL UP” →“DVD” →“L”
NOTE:
 Operation must be done within 20 seconds.
 Perform the operation of rear seat remote controller for head- rest display unit of each side.
4. When the rear seat remote operation is performed as shown on procedure 3, self-diagnosis screen is displayed.
Diagnosis item Display Description
Display Location Left/Right/Un-
known Installation location of headrest display unit is displayed.
NOTE:
If displayed location is different from the actual location or shown as “unknown”,
check location recognition signal circuit.
Software Ver. ***** Software version of headrest display unit is displayed.
Hardware Ver. ***** Hardware version of headrest display unit is displayed.
Seat Position OK Not used for this vehicle.
JSNIA3003ZZ
JSNIA3005ZZ
Revision: 2010 May2011 QX56

AV-50
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (HEADREST DISPLAY UNIT)
Finishing Self-diagnosis Mode
Self-diagnosis mode is canceled when pressing the enter switch of
rear seat remote controller.
JSNIA3004ZZ
Revision: 2010 May2011 QX56

AV
AV CONTROL UNITAV-53
< ECU DIAGNOSIS INFORMATION >
C
DE
F
G H
I
J
K L
M B A
O P16
(Y/L) 15
(B) Steering switch signal B Input Ignition
switch
ON Keep pressing VOL DOWN
switch.
0 V
Keep pressing VOL UP
switch. 1.0 V
Keep pressing switch. 2.0 V
Keep pressing switch. 3.0 V
Except for above. 5.0 V
19
(Y/R) Ground Battery power supply Input Ignition
switch
OFF — Battery voltage
20
(B) Ground Ground — Ignition
switch ON —0 V
26
(LG) Ground AUX image signal Input Ignition
switch ON At front AUX image is dis-
played.
29
(W/B) Ground Disk eject signal Input Ignition
switch
ON Pressing the eject switch. 0 V
Except for above. 5.0 V
30
(R/W) Ground Mode change signal Output Ignition
switch ON Driver's Audio Stage ON 0 V
Driver's Audio Stage OFF 8.5 V
33
(L) Ground
Composite image signal
ground —Ignition
switch ON —0 V
34
(P) Ground Composite image signal Output Ignition
switch ON When DVD, USB or front
AUX image is displayed on
headrest display unit LH or
RH.
46
(V) Ground AUX image signal ground — Ignition
switch ON —0 V
47 — Shield — — — —
49
(R/W) Ground Switch ground — Ignition
switch
ON —0 V
53 — Shield — — — —
65
(W) Ground Parking brake signal Input Ignition
switch ON Parking brake is applied. 0 V
Parking brake is released. 4.5 V
67
(W) Ground Composite image signal
ground —Ignition
switch ON —0 V
Te r m i n a l
(Wire color) Description
ConditionReference value
(Approx.)
+ – Signal name Input/
Output
SKIB2251J
SKIB2251J
Revision: 2010 May2011 QX56

AV-56
< ECU DIAGNOSIS INFORMATION >
AV CONTROL UNIT
106(W) 120
(R) Sound signal LH Output Ignition
switch ON When DVD or USB mode is
selected on headrest dis-
play unit LH or RH.
107 (B) 121
(G) Sound signal RH Output Ignition
switch ON When DVD or USB mode is
selected on headrest dis-
play unit LH or RH.
11 7 — S h i e l d — — — —
11 8 (O) 11 9
(W/L) AUX sound signal RH Input Ignition
switch ON When front AUX mode is
selected.
122 — Shield — — — —
129 (G) — USB ground — — — —
130 (R) — USB D
− signal — — — —
131 (W) — V BUS signal — — — —
132 (L) — USB D+ signal — — — —
133 — Shield — — — —
150 — FM sub Input — — —
151 — AM-FM main Input — — —
152 Ground Antenna amp. ON signal Input Ignition
switch ON —12.0 V
153 Ground GPS antenna signal Input Ignition
switch ON Not connected GPS anten-
na connector.
5.0 V
154 — Shield — — — —
157 Ground RGB digital image signal
(
− ) OutputIgnition
switch
ON Not connected connector. 1.3 V
Te r m i n a l
(Wire color) Description
ConditionReference value
(Approx.)
+ – Signal name Input/
Output
SKIB3609E
SKIB3609E
SKIB3609E
Revision: 2010 May2011 QX56

AV-62
< ECU DIAGNOSIS INFORMATION >
HEADREST DISPLAY UNIT
HEADREST DISPLAY UNIT
Reference ValueINFOID:0000000006216229
TERMINAL LAYOUT
PHYSICAL VALUES
JPNIA0007ZZ
Terminal
(Wire color) Description
ConditionReference value
(Approx.)
+ – Signal name Input/
Output
1
(L) Ground Ground — Ignition
switch ON —0 V
2
(V) Ground Battery power supply Input Ignition
switch
OFF — Battery voltage
3
(GR) Ground Ground — Ignition
switch ON —0 V
4
(L/R) Ground Battery power supply Input Ignition
switch OFF — Battery voltage
9
(B/R) Ground
Location recognition signal
for headrest display unit RH InputIgnition
switch
ON —0 V
10
(L/B) Ground Location recognition signal
for headrest display unit LH
InputIgnition
switch ON —0 V
11
(B) —AV communication signal
(H) Input/
Output —— —
12
(G) —AV communication signal
(H) Input/
Output —— —
13
(R) —
AV communication signal
(L) Input/
Output —— —
14
(W) —AV communication signal
(L) Input/
Output —— —
15 — Shield — — — —
18
(W/R) Ground ACC signal Input Ignition
switch OFF — 3.3 V
Ignition switch
ACC —0 V
Revision: 2010 May2011 QX56

AV
HEADREST DISPLAY UNITAV-63
< ECU DIAGNOSIS INFORMATION >
C
DE
F
G H
I
J
K L
M B A
O P
19
(L/Y) Ground Cont. ground — Ignition
switch ON —0 V
20
(W/L) Ground Image switch signal Output Ignition
switch ON When DVD, USB or front
AUX image is displayed on
headrest display unit.
0.5 V
When rear AUX image is
displayed on headrest dis-
play unit. 4.5 V
23
(R/L) Ground Composite image signal
ground
—Ignition
switch ON —0 V
24
(Y) Ground Composite image signal Input Ignition
switch ON When DVD, USB or front
AUX image is displayed on
headrest display unit.
25 — Shield — — — —
27
(R/W) Ground AV ground — Ignition
switch
ON —0 V
28 — Shield — — — —
30
(P) 29
(BR) Headphone sound signal
RH
InputIgnition
switch
ON Headphone sound output.
32
(SB) 31
(LG) Headphone sound signal
LH
InputIgnition
switch ON Headphone sound output.
Te r m i n a l
(Wire color) Description
ConditionReference value
(Approx.)
+ – Signal name Input/
Output
SKIB2251J
SKIB3609E
SKIB3609E
Revision: 2010 May2011 QX56