2011 INFINITI QX56 engine

SYSTEMTM-57
< SYSTEM DESCRIPTION > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O PLock-up Operation Condition Table
Lock-up released
 In the lock-up released state, the torque converter clutch control valve is set into the unlocked state by the
torque converter clutch solenoid and the lock-up apply pressure is drained.
in this way, the torque converter clutch piston is not coupled.
Lock-up Applied
 In the lock-up applied state, the torque converter clutch control valve is set into the locked state by the
torque converter clutch solenoid and lock-up apply pressure is generated.
In this way, the torque converter clutch piston is pressed and coupled.
Smooth Lock-up Control
When shifting from the lock-up released state to the lock- up applied state, the current output to the torque con-
verter clutch solenoid is controlled with the TCM. In this way, when shifting to the lock-up applied state, the
torque converter clutch is temporarily set to the half-clutched state to reduce the shock.
Half-clutched State The current output from the TCM to the torque converte r clutch solenoid is varied to steadily increase the
torque converter clutch solenoid pressure.
In this way, the lock-up apply pressure gradually rises and while the torque converter clutch piston is put into
half-clutched states, the torque conv erter clutch piston operating pressure is increased and the coupling is
completed smoothly.
Slip Lock-up Control In the slip region, the torque converter clutch solenoid current is controlled with the TCM to put it into the
half-clutched state. This absorbs the engine tor que fluctuation and lock-up operates from low speed.
This raises the fuel efficiency fo r 2GR, 3GR, 4GR, 5GR, 6GR and 7GR.
A/T SHIFT LOCK SYSTEM
JSDIA0847GB
Selector lever “D” position “M” position
Gear position 765432765432
Lock-up×––––– ××××××
Slip lock-up ××××××××××××
Revision: 2010 May2011 QX56

DIAGNOSIS SYSTEM (TCM)TM-61
< SYSTEM DESCRIPTION > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
DIAGNOSIS SYSTEM (TCM)
CONSULT-III Function (TRANSMISSION)INFOID:0000000006226781
CONSULT-III APPLICATION ITEMS
*: Although “Function Test” and “Special Function” are selectable, do not use its.
WORK SUPPORT
SELF DIAGNOSTIC RESULTS
Refer to TM-78, "DTC Index".
IGN Counter
The IGN counter is indicated in Fr eeze frame data (FFD) and indicates the number of times that the ignition
switch is turned ON after returning to the normal state from DTC.
 CAN malfunction
- The number is 0 when a malfunction is detected now.
- The number increases like 1 → 2 → 3...38 → 39 after returning to the normal condition whenever ignition
switch OFF → ON.
- The number is fixed to 39 until the self-di agnosis results are erased if it is over 39.
 Other than CAN malfunction
- The number is 0 when a malfunction is detected now.
- The number increases like 1 → 2 → 3...254 → 255 after returning to the normal condition whenever ignition
switch OFF → ON.
- The number is fixed to255 until the self-diagno sis results are erased if it is over 255.
DATA MONITOR
X: Standard, —: Not applicable, : Option
Diagnostic test mode Function
Work Support This mode enables a technician to adjust some devices faster and more accurately.
Self Diagnostic Results Retrieve DTC from ECU and display diagnostic items.
Data Monitor Monitor the input/output signal of the control unit in real time.
CAN Diagnosis This mode displays a network diagnosis result about CAN by a diagram.
CAN Diagnostic Support
Monitor It monitors the status of CAN communication.
DTC & SRT confirmation The status of system monitoring tests and the self-diagnosis status/result can be confirmed.
ECU Identification Display the ECU identification number (part number etc.) of the selected system.
Function Test* This mode can show results of self-diagnosis of ECU with either “OK” or “NG”. For engine, more prac-
tical tests regarding sensors/switches and/or actuators are available.
Special Function* Other results or histories, etc. that are recorded in ECU are displayed.
Item name Description
G SENSOR CALIBRATION Calibrates G sensor.
Monitored item (Unit) Monitor Item Selection
Remarks
ECU IN-
PUT SIG- NALS MAIN SIG-
NALS SELEC-
TION
FROM
ITEM
VHCL/S SE-A/T (km/h or mph) X X Displays the vehicle speed calculated by the
TCM from the output shaft revolution.
ESTM VSP SIG (km/h or mph) X — Displays the vehicle speed signal received via
CAN communication.
OUTPUT REV (rpm) X X Displays the output speed calculated from the
pulse signal of output speed sensor.
Revision: 2010 May2011 QX56

TM-62
< SYSTEM DESCRIPTION >[7AT: RE7R01B]
DIAGNOSIS SYSTEM (TCM)
INPUT SPEED (rpm) X X Displays the input speed calculated from front
sun gear revolution and front carrier revolution.
F SUN GR REV (rpm) — — Displays the front sun gear revolution calculat-
ed from the pulse signal of input speed sensor
1.
F CARR GR REV (rpm) — — Displays the front carrier gear revolution calcu-
lated from the pulse signal of input speed sen-
sor 2.
ENGINE SPEED (rpm) X X Displays the engine speed received via CAN
communication.
TC SLIP SPEED (rpm) — X Displays the revolution difference between in-
put speed and engine speed.
ACCELE POSI (0.0/8) X — Displays the accelerator position estimated val-
ue received via CAN communication.
THROTTLE POSI (0.0/8) X X Displays the throttle position received via CAN
communication.
ATF TEMP 1 ( °C or °F) X X Displays the ATF temperature of oil pan calcu-
lated from the signal voltage of A/T fluid tem-
perature sensor.
ATF TEMP 2 ( °C or °F) X X Displays the ATF temperature estimated value
of torque converter outlet calculated from the
signal voltage of A/T fluid temperature sensor.
ATF TEMP SE 1 (V) — — Displays the signal voltage of A/T fluid temper-
ature sensor.
BATTERY VOLT (V) X — Displays the power supply voltage of TCM.
LINE PRES SOL (A) — X Displays the command current from TCM to the
line pressure solenoid.
TCC SOLENOID (A) — X Displays the command current from TCM to the
torque converter clutch solenoid.
L/B SOLENOID (A) — X Displays the command current from TCM to the
low brake solenoid.
FR/B SOLENOID (A) — X Displays the command current from TCM to the
front brake solenoid.
HLR/C SOL (A) — X Displays the command current from TCM to the
high and low reverse clutch solenoid.
I/C SOLENOID (A) — X Displays the command current from TCM to the
input clutch solenoid.
D/C SOLENOID (A) — X Displays the command current from TCM to the
direct clutch solenoid.
2346/B SOL (A) — X Displays the command current from TCM to the
2346 brake solenoid.
L/P SOL MON (A) — — Monitors the command current from TCM to the
line pressure solenoid, and displays the moni-
tor value.
TCC SOL MON (A) — — Monitors the command current from TCM to the
torque converter clutch solenoid, and displays
the monitor value.
L/B SOL MON (A) — — Monitors the command current from TCM to the
low brake solenoid, and displays the monitor
value.
Monitored item (Unit)
Monitor Item Selection
Remarks
ECU IN-
PUT SIG- NALS MAIN SIG-
NALS SELEC-
TION
FROM ITEM
Revision: 2010 May2011 QX56

DIAGNOSIS SYSTEM (TCM)TM-63
< SYSTEM DESCRIPTION > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
FR/B SOL MON (A) — — Monitors the command current from TCM to the
front brake solenoid, and displays the monitor
value.
HLR/C SOL MON (A) — — Monitors the command current from TCM to the
high and low reverse clutch solenoid, and dis-
plays the monitor value.
I/C SOL MON (A) — — Monitors the command current from TCM to the
input clutch solenoid, and displays the monitor
value.
D/C SOL MON (A) — — Monitors the command current from TCM to the
direct clutch solenoid, and displays the monitor
value.
2346/B SOL MON (A) — — Monitors the command current from TCM to the
2346 brake solenoid, and displays the monitor
value.
GEAR RATIO — X Displays the gear ratio calculated from input
speed and output speed.
ENGINE TORQUE (Nm) — — Displays the engine torque estimated value re-
ceived via CAN communication.
ENG TORQUE D (Nm) — — Displays the engine torque estimated value re-
flected the requested torque of each control unit
received via CAN communication.
INPUT TRQ S (Nm) — — Displays the input torque using for the oil pres-
sure calculation process of shift change control.
INPUT TRQ L/P (Nm) — — Displays the input torque using for the oil pres-
sure calculation process of line pressure con-
trol.
TRGT PRES L/P (kPa, kg/cm
2 or psi)—— Displays the target oil pressure value of torque
converter clutch solenoid valve calculated by
the oil pressure calculation process of lock-up
control.
TRGT PRES TCC (kPa, kg/cm
2 or psi)—— Displays the target oil pressure value of torque
converter clutch solenoid valve calculated by
the oil pressure calculation process of shift
change control.
TRGT PRES L/B (kPa, kg/cm
2 or psi)—— Displays the target oil pressure value of low
brake solenoid valve calculated by the oil pres-
sure calculation process of shift change control.
TRGT PRE FR/B (kPa, kg/cm
2 or psi)—— Displays the target oil pressure value of front
brake solenoid valve calculated by the oil pres-
sure calculation process of shift change control.
TRG PRE HLR/C (kPa, kg/cm
2 or psi)—— Displays the target oil pressure value of high
and low reverse clutch solenoid valve calculat-
ed by the oil pressure calculation process of
shift change control.
TRGT PRES I/C (kPa, kg/cm
2 or psi)—— Displays the target oil pressure value of input
clutch solenoid valve calculated by the oil pres-
sure calculation process of shift change control.
TRGT PRES D/C (kPa, kg/cm
2 or psi)—— Displays the target oil pressure value of direct
clutch solenoid valve calculated by the oil pres-
sure calculation process of shift change control.
Monitored item (Unit)
Monitor Item Selection
Remarks
ECU IN-
PUT SIG- NALS MAIN SIG-
NALS SELEC-
TION
FROM ITEM
Revision: 2010 May2011 QX56

TM-68
< ECU DIAGNOSIS INFORMATION >[7AT: RE7R01B]
TCM
ECU DIAGNOSIS INFORMATION
TCM
Reference ValueINFOID:0000000006226782
VALUES ON DIAGNOSIS TOOL
NOTE:
1. The CONSULT-III electrically displays shift timi
ng and lock-up timing (that is, operation timing of each
solenoid).
Check for time difference between actual shift timi ng and the CONSULT-III display. If the difference is
noticeable, mechanical parts (except solenoids, sens ors, etc.) may be malfunctioning. Check mechanical
parts in accordance with the specified diagnostic procedures.
2. Shift schedule (that implies gear position) on CONSULT-III may slightly differ from that is described in Ser-
vice Manual. This occurs because of the reasons as per the following:
- Actual shift schedule has more or less tolerance or allowance
- Shift schedule in Service Manual refers to the point where shifting starts
- Gear position on CONSULT-III indicates the point where shifting completes
3. Display of solenoid valves on CONSULT-III changes at t he start of shifting, while gear position is displayed
upon completion of shifting (which is computed by TCM).
CONSULT-III MONITOR ITEM
Item name Condition Value / Status (Approx.)
VHCL/S SE-A/T During driving Approximately equals the speed-
ometer reading.
ESTM VSP SIG During driving Approximately equals the speed-
ometer reading.
OUTPUT REV During driving (lock-up ON) Tachometer / Gear ratio
INPUT SPEED During driving (lock-up ON) Approximately equals the engine
speed.
F SUN GR REV During driving Revolution of front sun gear is indi-
cated.
F CARR GR REV During driving Revolution of front carrier is indi-
cated.
ENGINE SPEED Eng ine running Closely equals the tachometer
reading.
TC SLIP SPEED During driving Engine speed − Input speed
ACCELE POSI Accelerator pedal is released 0.0/8
Accelerator pedal is fully depressed 8.0/8
THROTTLE POSI Accelerator pedal is released 0.0/8
Accelerator pedal is fully depressed 8.0/8
ATF TEMP 1 Ignition switch ON Temperature of ATF in the oil pan is
indicated.
ATF TEMP 2 Ignition switch ON Temperature of ATF at the exit of
torque converter.
AT F T E M P S E 1 0 °C (32 ° F) – 20 °C (68 °F) – 80 °C (176 °F) 3.3 – 2.7 – 0.9 V
BATTERY VOLT Ignition switch ON Battery voltage (11 V – 14 V)
LINE PRES SOL During driving 0.2 – 0.6 A
TCC SOLENOID Slip lock-up is active 0.2 – 0.8 A
Lock-up is active 0.8 A
Other than the above 0 A
L/B SOLENOID Low brake is engaged 0.6 – 0.8 A
Low brake is disengaged 0 – 0.05 A
Revision: 2010 May2011 QX56

TCM
TM-69
< ECU DIAGNOSIS INFORMATION > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
FR/B SOLENOID Front brake is engaged 0.6 – 0.8 A
Front brake is disengaged 0 – 0.05 A
HLR/C SOL High and low reverse clutch is disengaged 0.6 – 0.8 A
High and low reverse clutch is engaged 0 – 0.05 A
I/C SOLENOID Input clutch is disengaged 0.6 – 0.8 A
Input clutch is engaged 0 – 0.05 A
D/C SOLENOID Direct clutch is disengaged 0.6 – 0.8 A
Direct clutch is engaged 0 – 0.05 A
2346/B SOL 2346 brake is engaged 0.6 – 0.8 A
2346 brake is disengaged 0 – 0.05 A
L/P SOL MON During driving 0.2 – 0.6 A
TCC SOL MON Slip lock-up is active 0.2 – 0.8 A
Lock-up is active 0.8 A
Other than the above 0 A
L/B SOL MON Low brake is engaged 0.6 – 0.8 A
Low brake is disengaged 0 – 0.05 A
FR/B SOL MON Front brake is engaged 0.6 – 0.8 A
Front brake is disengaged 0 – 0.05 A
HLR/C SOL MON High and low reverse clutch is disengaged 0.6 – 0.8 A
High and low reverse clutch is engaged 0 – 0.05 A
I/C SOL MON Input clutch is disengaged 0.6 – 0.8 A
Input clutch is engaged 0 – 0.05 A
D/C SOL MON Direct clutch is disengaged 0.6 – 0.8 A
Direct clutch is engaged 0 – 0.05 A
2346/B SOL MON 2346 brake is engaged 0.6 – 0.8 A
2346 brake is disengaged 0 – 0.05 A
GEAR RATIO Driving with 1GR 4.887
Driving with 2GR 3.170
Driving with 3GR 2.027
Driving with 4GR 1.412
Driving with 5GR 1.000
Driving with 6GR 0.864
Driving with 7GR 0.775
ENGINE TORQUE During driving Changes the value according to
the acceleration or deceleration.
ENG TORQUE D During driving Changes the value according to
the acceleration or deceleration.
INPUT TRQ S During driving Changes the value according to
the acceleration or deceleration.
INPUT TRQ L/P During driving Changes the value according to
the acceleration or deceleration.
TRGT PRES L/P Selector lever in “P” an
d “N” positions 490 kPa
Other than the above 490 – 1370 kPa
TRGT PRES TCC Slip lock-up is active 0 – 600 kPa
Lock-up is active 600 kPa
Other than the above 0 kPa
Item name Condition Value / Status (Approx.)
Revision: 2010 May2011 QX56

TCM
TM-77
< ECU DIAGNOSIS INFORMATION > [7AT: RE7R01B]
C
EF
G H
I
J
K L
M A
B
TM
N
O P
1ST ENGINE BRAKE PROTECTION CONTROL
Controls the engine brake so as not to make effective by turning the front brake solenoid output to OFF when
each solenoid becomes the electricity pattern of 1st engine brake during driving at the vehicle speed 25 km/h
or more in any positions other than “R” position and 1GR.
TCM HIGH TEMPERATURE PROTECTION CONTROL
Limit the accelerator opening and forcibly control the vehi cle to the low torque driving when the electronic sub-
strate in TCM reaches the high temperature.
DTC Inspection Priority ChartINFOID:0000000006226785
If some DTCs are displayed at the same time, perfo rm inspections one by one based on the priority as per the
following list.
Malfunction detection condition Vehicle speed: 10 km/h (7 MPH) or more
Control at malfunction Neutral
Normal return condition  Vehicle speed: 8 km/h (5 MPH) or less
and
 Engine speed: 2,200 rpm or less
Vehicle behavior  The torque transmission cannot be performed
 There is a shock just before a vehicle stop
Malfunction detection condition Select lever and gear: Any position other than “R” position and 1GR
and
 Vehicle speed: More than 25 km/h (16 MPH)
Control at malfunction Front brake solenoid output signal; OFF
Normal return condition Other than detection condition of malfunction
Vehicle behavior Does not exist
Malfunction detection condition TCM electronic substrate temperature
145
°C (293 °F) and 120 seconds
or
150 °C (302 °F)
Control at malfunction Accelerator opening: 0.5/8 or less
Normal return condition  TCM electronic substrate temperature: Less than 140
°C (284 °F)
and
 Vehicle speed: 5 km/h (3 MPH) or less
Vehicle behavior Accelerator opening: output torque of approximately 0.5/8
Priority Detected items (DTC) Reference 1 U1000 CAN COMM CIRCUIT TM-103, "
DTC Logic"
Revision: 2010 May2011 QX56

TM-78
< ECU DIAGNOSIS INFORMATION >[7AT: RE7R01B]
TCM
DTC Index
INFOID:0000000006226786
NOTE:
 If some DTCs are displayed at the same time, per form inspections one by one based on the priority as per
the following list. Refer to TM-77, "
DTC Inspection Priority Chart".
 The IGN counter is indicated in Freeze frame data (FFD). Refer to TM-61, "
CONSULT-III Function (TRANS-
MISSION)".
2P0615 STARTER RELAY
TM-104, "
DTC Logic"
P0705 T/M RANGE SWITCH ATM-106, "DTC Logic"
P0710 FLUID TEMP SENSOR ATM-107, "DTC Logic"
P0717 INPUT SPEED SENSOR ATM-109, "DTC Logic"
P0720 OUTPUT SPEED SENSOR TM-110, "DTC Logic"
P0740 TORQUE CONVERTERTM-128, "DTC Logic"
P0745 PC SOLENOID ATM-131, "DTC Logic"
P0750 SHIFT SOLENOID ATM-132, "DTC Logic"
P0775 PC SOLENOID BTM-133, "DTC Logic"
P0795 PC SOLENOID CTM-136, "DTC Logic"
P2713 PC SOLENOID DTM-147, "DTC Logic"
P2722 PC SOLENOID ETM-148, "DTC Logic"
P2731 PC SOLENOID FTM-149, "DTC Logic"
P2807 PC SOLENOID GTM-150, "DTC Logic"
3P0729 6GR INCORRECT RATIO
TM-114, "
DTC Logic"
P0730 INCORRECT GR RATIOTM-116, "DTC Logic"
P0731 1GR INCORRECT RATIOTM-118, "DTC Logic"
P0732 2GR INCORRECT RATIOTM-120, "DTC Logic"
P0733 3GR INCORRECT RATIOTM-122, "DTC Logic"
P0734 4GR INCORRECT RATIOTM-124, "DTC Logic"
P0735 5GR INCORRECT RATIOTM-126, "DTC Logic"
P0744 TORQUE CONVERTERTM-129, "DTC Logic"
P0780 SHIFTTM-134, "DTC Logic"
P1730 INTERLOCKTM-140, "DTC Logic"
P1734 7GR INCORRECT RATIOTM-142, "DTC Logic"
4U0300 CAN COMM DATA
TM-102, "
DTC Logic"
P0725 ENGINE SPEED TM-112, "DTC Logic"
P1705 TP SENSORTM-137, "DTC Logic"
P1721 VEHICLE SPEED SIGNALTM-138, "DTC Logic"
P1815 M-MODE SWITCHTM-144, "DTC Logic"
Priority Detected items (DTC) Reference
DTC*1
Items
(CONSULT-III screen terms) Reference
MIL*2, “ENGINE” with
CONSULT-III or GST CONSULT-III only
“TRANSMISSION”
— P0615 STARTER RELAY TM-104
P0705 P0705 T/M RANGE SWITCH A TM-106
P0710 P0710 FLUID TEMP SENSOR ATM-107
P0717 P0717 INPUT SPEED SENSOR ATM-109
P0720 P0720 OUTPUT SPEED SENSOR TM-110
Revision: 2010 May2011 QX56