2011 INFINITI QX56 engine

SYSTEMSCS-55
< SYSTEM DESCRIPTION > [AIR LEVELIZER CONTROL SYSTEM]
C
D
F
G H
I
J
K L
M A
B
SCS
N
O P
Vehicle height raises [When starting engi
ne, if vehicle height of vehicle rear continues for 30 seconds or more in a
status that is 15 mm (0.59 in) or less than standard vehicle height]
1. Vehicle height sensor detects vehicle height status, and transmits this information to air levelizer control
module.
2. Air levelizer control module turns air compressor relay ON and operates air compressor.
3. Air compressor charges air in air chamber of shock absorber.
4. Vehicle height raises, and control is complete when status is −1 mm ( −0.04 in) of standard vehicle height
value.
Vehicle height lowers [When starting engine, if vehicle height of vehicle rear continues for 30 seconds or more in a
status that is 15 mm (0.59 in) or more of standard vehicle height]
1. Vehicle height sensor detects vehicle height status, and transmits this information to air levelizer control
module.
2. Air levelizer control module turns exhaust solenoid of air compressor ON.
3. Air compressor discharges air from air chamber of shock absorber.
4. Vehicle height lowers, and control is complete when st atus is +1 mm (+0.04 in) of standard vehicle height.
Fail-safeINFOID:0000000006256051
If malfunction is detected, control stops.
The system may enter fail-safe mode under certain conditions (for example, over-laden conditions) when elec-
tronic circuit is normal.
In this case, always check that the system re turns to normal by starting engine after unloading load.
JSEIA0221GB
Revision: 2010 May2011 QX56

DIAGNOSIS SYSTEM (AIR LEVELIZER CONTROL MODULE)
SCS-57
< SYSTEM DESCRIPTION > [AIR LEVELIZER CONTROL SYSTEM]
C
D
F
G H
I
J
K L
M A
B
SCS
N
O P
ACTIVE TEST
CAUTION:
 Perform the procedure when the vehicle is stopped.
 Be careful that battery is not discharged when pe rforming the procedure while engine is stopped.
VHCL HGT INIT VAL (V)  Displays voltage when standard vehicle height is set.
 Value does not change until setting of standard vehicle height is performed again.
COMPRESSOR Displays operation status of air compressor.
EXH SOLENOID Displays operation status of exhaust solenoid.
ENG SPEED SIG Displays operation status of engine.
WARNING LAMP Displays turning ON st atus of CK SUSP indicator lamp.
Monitored item (Unit) Remarks
Item name Description
COMPRESSOR Air compress or can be operated.
EXHAUST SOLENOID Ehaust solenoid of air compressore can be operated.
WARNING LAMP CK SUSP indicator lamp can be turned ON or OFF.
Revision: 2010 May2011 QX56

SCS-58
< ECU DIAGNOSIS INFORMATION >[AIR LEVELIZER CONTROL SYSTEM]
AIR LEVELIZER CONTROL MODULE
ECU DIAGNOSIS INFORMATION
AIR LEVELIZER CONTROL MODULE
Reference ValueINFOID:0000000006256053
VALUES ON DIAGNOSIS TOOL
TERMINAL LAYOUT
PHYSICAL VALUES
Item name Condition Value/Status (Approx.)
IGN VOLT Ignition switch ON 10 – 16 V
VHCL HT INTLZ STA Completion of the standard vehicle height setting CMPLT
Other than the above INCMP
VHCL HT INIT SLCT Completion of the standard vehicle height setting 1
Other than the above 0
VHCL HEIGHT SEN Lift up the vehicle 2.8 – 3.8 V
VHCL HT CNVSN VL Lift down the vehicle −15 – 15 mm
VHCL HGT FIX TIME Lift up the vehicle 0 h
VHCL HGT INIT VAL Completion of the standard vehicle height setting 2.800 – 3.800 V
Other than the above 0 V
COMPRESSOR When the air compressor is operating On
Other than the above Off
EXH SOLENOID When exhaust solenoid is operating On
Other than the above Off
ENG SPEED SIG Engine running RUN
Other than the above STOP
WARNING LAMP When CK SUSP indicator lamp is ON On
Other than the above Off
JSDIA0057ZZ
Terminal
(Wire color) Description
ConditionReference value
(Approx.)
+ − Signal name Input/
Output
2
(B) Ground GND — Always Less than 1
Ω
3
(V) Ground Air compressor relay Output IGN ON Air compressor: ON 9 – 16 V
Air compressor: OFF Less than 2 V
4
(L/W) Ground Vehicle height sensor
(GND) — Always Less than 1
Ω
Revision: 2010 May2011 QX56

AIR LEVELIZER CONTROL MODULESCS-59
< ECU DIAGNOSIS INFORMATION > [AIR LEVELIZER CONTROL SYSTEM]
C
D
F
G H
I
J
K L
M A
B
SCS
N
O P
Fail-safeINFOID:0000000006256054
If malfunction is detected, control stops.
The system may enter fail-safe mode under certain condi tions (for example, over-laden conditions) when elec-
tronic circuit is normal.
In this case, always check that the system re turns to normal by starting engine after unloading load.
DTC Inspection Priority ChartINFOID:0000000006256055
If some DTCs are displayed at the same time, per form inspections one by one based on the following priority
chart.
DTC IndexINFOID:0000000006256056
5
(W) Ground Vehicle height sensor
(SIGNAL) InputIGN ON 0.2 – 4.6 V
IGN OFF 0 V
7
(P) 16
(L) CAN-L
Input/
Output — 54 – 69
Ω
9
(P/L) Ground Air levelizer co
ntrol module
power supply InputIGN ON 10 – 16 V
IGN OFF 0 V
11
(V/W) Ground Exhaust solenoid Output IGN ON Exhaust solenoid: ON 9 – 16 V
Exhaust solenoid: OFF Less than 2 V
13
(R) Ground Vehicle height sensor
(Power supply)
OutputIGN ON 4.5 – 5.5 V
IGN OFF 0 V
16
(L) 7
(P) CAN-H Input/
Output — 54 – 69
Ω
Te r m i n a l
(Wire color) Description
ConditionReference value
(Approx.)
+ − Signal name Input/
Output
Priority Detected items (DTC)
1  U1000 CAN COMM CIRCUIT
 U1010 CONTROL UNIT (CAN)
2  C1801 VHCL HEIGHT SENSOR
 C1802 AIR SUS COMPRS RELAY
 C1803 AIR SUS EXH SOL
 C1806 VHCL HEIGHT SEN FIX
 C1807 VHCL HEIGHT SEN VOLT
3  C1804 VHCL HEIGHT ADJ UP
 C1805 VHCL HEIGHT ADJ DOWN
 C1808 AIR SUS COMPRS FNCTN
DTC CONSULT-III display Reference page
C1801 VHCL HEIGHT SENSOR SCS-69
C1802 AIR SUS COMPRS RELAYSCS-72
C1803 AIR SUS EXH SOLSCS-74
C1804 VHCL HEIGHT ADJ UPSCS-77
C1805 VHCL HEIGHT ADJ DOWNSCS-80
C1806 VHCL HEIGHT SEN FIXSCS-81
C1807 VHCL HEIGHT SEN VOLTSCS-82
C1808 AIR SUS COMPRS FNCTNSCS-84
Revision: 2010 May2011 QX56

SCS-66
< BASIC INSPECTION >[AIR LEVELIZER CONTROL SYSTEM]
DIAGNOSIS AND REPAIR WORKFLOW
YES >> GO TO 7.
NO >> Check harness and connectors based on the information obtained by interview. Refer to
GI-40,
"Intermittent Incident".
7.FINAL CHECK
With CONSULT-III
1. Check the reference value for “E-SUS”.
2. Recheck the symptom and check that the symp tom is not reproduced on the same conditions.
Is the symptom reproduced?
YES >> GO TO 3.
NO >> INSPECTION END
Diagnostic Work SheetINFOID:0000000006256059
Description
 In general, customers have their own criteria for a pr oblem. Therefore, it is important to understand the
symptom and status well enough by asking the customer about his/her concerns carefully. To systemize all
the information for the diagnosis, prepare the inte rview sheet referring to the interview points.
 In some cases, multiple conditions that appear simultaneously may cause a DTC to be detected.
INTERVIEW SHEET SAMPLE
Interview sheet
Custmer
name MR/MS Registration
number Initial year
registration
Vehicle type VIN
Storage date Engine Mileage km/Mile
Symptom † Does not operate ( ) function
† Warning lamp for ( ) turns ON
† Noise † Vibration
† Other
( )
First occurrence † Recently † Other ( )
Frequency of occurrence † Always † Under a certain conditions of † Sometimes ( time/day)
Climate con-
ditions †
Irrelevant
Weather † Fine † Cloud † Rain † Snow † Others ( )
Temperature † Hot † Warm † Cool † Cold † Temp. [Approx. °C ( °F)]
Relative humidity † High † Moderate † Low
Road conditions † Urban area † Suburb area † Highway
† Mountainous road (uphill or downhill) † Rough road
Operating condition, etc. † Irrelevant
† When engine starts † During idling
† During driving † During acceleration † At constant speed driving
† During deceleration
† During cornering (righ t curve or left curve)
† When steering wheel is steered (to right or to left)
Memo
Revision: 2010 May2011 QX56

STANDARD VEHICLE HEIGHT SETTINGSCS-67
< BASIC INSPECTION > [AIR LEVELIZER CONTROL SYSTEM]
C
D
F
G H
I
J
K L
M A
B
SCS
N
O P
STANDARD VEHICL E HEIGHT SETTING
DescriptionINFOID:0000000006256060
Air levelizer control module enables precise control, by acquiring memorized standard vehicle height and sig-
nal (vehicle height) from vehicle height sensor. For this reason, always set standard vehicle height after per-
forming the following operations.
 Removal and installation or replacement of vehicle height sensor
 Replacement of air levelizer control module
Work ProcedureINFOID:0000000006256061
1.CLEAR STANDARD VEHICLE HEIGHT
With CONSULT-III
1. Lift up the vehicle. CAUTION:
Check that tires never contact the ground.
2. Start the engine.
3. Select “COMPRESSOR” in “Active Test” in “E-SUS”.
4. Touch “ON” and wait 60 seconds or more.
5. Touch “OFF”.
6. Select “CLEAR HEIGHT INI” in “Work Support” in “E-SUS”.
7. Touch “Start”.
8. Touch “Clear”. NOTE:
CONSULT-III continues indicating "EXECUTING". The completion of the standard vehicle height erasing
can be checked by the CK SUSP indicator lamp ON condition.
Does CK SUSP indicator lamp turn ON?
YES >> GO TO 2.
NO >> Perform step 1 again.
2.ADJUST STANDARD VEHICLE HEIGHT
With CONSULT-III
1. Select “ADJUST HEIGHT INI” in “Work Support” in “E-SUS”.
2. Touch “Start”.
3. Touch “Initial 1”. NOTE:
CONSULT-III continues indicating "EXECUTING". T he completion of the standard vehicle height adjust-
ment can be checked by the CK SUSP indicator lamp OFF condition.
Does CK SUSP indicator lamp turn OFF?
YES >> GO TO 3.
NO >> Perform step 1 again.
3. ADJUST VEHICLE HEIGHT
With CONSULT-III
1. Lift down the vehicle. CAUTION:
Check that the lift is fully lowered.
2. Select “STANDARD HEIGHT LEVEL” in “Work Support” in “E-SUS”.
3. Touch “Start”.
4. Touch “Revert” and wait 120 seconds or more.
5. Although CONSULT-III continues indicating "EXECUTIN G", select “VHCL HGT CNVSN VL” in “Data Mon-
itor” in “E-SUS”.
Is value within
−15 – 15 mm?
YES >> GO TO 4.
NO >> Perform step 1 again.
4.CHECK DTC
With CONSULT-III
Revision: 2010 May2011 QX56

C1801 VHCL HEIGHT SENSORSCS-69
< DTC/CIRCUIT DIAGNOSIS > [AIR LEVELIZER CONTROL SYSTEM]
C
D
F
G H
I
J
K L
M A
B
SCS
N
O P
DTC/CIRCUIT DIAGNOSIS
C1801 VHCL HEIGHT SENSOR
DTC LogicINFOID:0000000006256062
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previous ly conducted, always turn ignition switch OFF
andwait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT-III
1. Turn ignition switch ON and wait 60 seconds or more.
2. Perform “Self Diagnostic Results” in “E-SUS”.
Is
“C1801” detected ?
YES >> Go to SCS-69, "DiagnosisProcedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006256063
1.CHECK APPEARANCE
Visually check for malfunction of suspension components, installing malfunction, or deformation of vehicle
height sensor.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repaire or replace damaged parts.
2.CHECK POWER SUPPLY CIRCUIT (PART 1)
1. Disconnect vehicle height sensor connector.
2. Turn ignition switch ON. CAUTION:
Never start the engine.
3. Check voltage between vehicle height sensor harness connector and ground.
Is the inspection result normal?
YES >> GO TO 4.
NO >> GO TO 3.
3.CHECK POWER SUPPLY CIRCUIT (PART 2)
1. Turn ignition switch OFF.
2. Disconnect air levelizer control module connector.
DTC Display itemI Malfunction detected condition Possible cause
C1801 VHCL HEIGHT SENSOR Signal voltage of the vehicle height sensor remains 0.2
V or less or 4.6 V or more continuously for 60 seconds
during sensor voltage (4.5 – 5.5 V) output by the air lev-
elizer control module.  Harness or connectors
(Sensor circuit is open.)
 Vehicle height sensor
 Air levelizer control module
 Rear suspension component parts
Vehicle height sensor —Voltage
Connector Terminal
C13 1 Ground 4.5 – 5.5 V
Revision: 2010 May2011 QX56

SCS-72
< DTC/CIRCUIT DIAGNOSIS >[AIR LEVELIZER CONTROL SYSTEM]
C1802 AIR SUS COMPRS RELAY
C1802 AIR SUS COMPRS RELAY
DTC LogicINFOID:0000000006256065
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previous ly conducted, always turn ignition switch OFF
andwait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT-III
1. Turn ignition switch ON and wait 10 seconds or more.
2. Select “COMPRESSOR” in “Active Test” in “E-SUS”.
3. Touch “ON” and wait 5 seconds or more.
4. Select “Self Diagnostic Result” in “E-SUS”.
Is
“C1802” detected ?
YES >> Go to SCS-72, "DiagnosisProcedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006256066
1.CHECK AIR COMPRESSOR ON SIGNAL FROM AIR LEVELIZER CONTROL MODULE
CONSULT-III
1. Disconnect air compressor relay connector.
2. Turn ignition switch ON. CAUTION:
Never start the engine.
3. Select “COMPRESSOR” in “Active Test” in “E-SUS”.
4. Touch “ON”.
5. While operating test item, check voltage betw een air compressor relay harness connector and ground.
Is the inspection result normal?
YES >> GO TO 4.
NO >> GO TO 2.
2.CHECK HARNESS BETWEEN AIR LEVELIZER CO NTROL MODULE AND AIR COMPRESSOR RELAY
1. Turn ignition switch OFF.
2. Disconnect air levelizer control module connector.
DTC Display item Malfunction detected condition Possible cause
C1802 AIR SUS COMPRS RELAY  Output voltage of the air compressor relay remains
9 V or less continuously for 5 seconds during air
compressor ON signal output by the air levelizer
control module.
 Output voltage of the air compressor relay remains
2 V or more continuously for 10 seconds during air
compressor OFF signal output by the air levelizer
control module.  Harness or connector
 Air compressor relay
 Air levelizer control module
Air compressor relay
—Voltage
Connector Terminal
E116 2 Ground 9 – 16 V
Revision: 2010 May2011 QX56