2011 INFINITI QX 4WD

Warning light and display
Condition A :
The chime sounds and the Intelligent Cruise
Control (ICC) system is canceled automatically
in the conditions described below. Part of the
system display will come on or blink, making it
impossible to set.
●When the VDC is turned off
● When the ABS or VDC operates
● When a tire slips ●
When driving into a strong light (i.e., sun-
light)
● When the SNOW mode switch is pushed on
● When the 4WD shift switch is in the 4H or 4L
position
Action to take :
When the conditions listed above are no longer
present, turn the system off using the ICC MAIN
switch. Turn the ICC system back on to use the
system.
Condition B :
When the sensor window is dirty, making it
impossible to detect a vehicle ahead, the ICC
system is automatically canceled.
The chime sounds and the ICC system warning
light (orange) will come on and the CLEAN
SENSOR indicator will appear.
Action to take :
If the warning light comes on, park the vehicle
in a safe place, turn the engine off. Clean the
sensor window with a soft cloth and then
perform the settings again.
SSD1110SSD0989
5-56Starting and driving

Under the following conditions, the Distance
Control Assist system will not operate and the
Distance Control Assist (DCA) system switch
indicator will blink:
●When the SNOW mode is pushed (SNOW
mode switch) (To use the DCA system, turn
off the SNOW mode switch, then turn on the
dynamic driver assistance switch.)
For details about the SNOW mode switch,
see “SNOW MODE” later in this section. ●
When the 4WD shift switch is in the 4H or 4L
position. (To use the DCA system, place the
4WD shift switch in the AUTO position, then
turn on the dynamic driver assistance switch
(for 4WD models).
For details about the 4WD shift switch, see
“INFINITI ALL-MODE 4WD” earlier in this
section.
● When the VDC system is off (To use the DCA
system, turn on the VDC, then push the
dynamic driver assistance switch.)
For details about the VDC system, see “VE-
HICLE DYNAMIC CONTROL (VDC) SYSTEM”
later in this section.
● When ABS or VDC (including the traction
control system) is operating
● When driving into a strong light (i.e., sun-
light) When the Conventional (fixed speed) cruise
control mode is operating, the DCA system will
not operate. (To use the DCA system, turn the
Conventional (fixed speed) cruise control mode
off, then push the dynamic driver assistance
switch.)
For details about the Conventional (fixed speed)
cruise control mode, see “INTELLIGENT CRUISE
CONTROL (ICC) SYSTEM” earlier in this section.
When the engine is turned off, the system is
automatically turned off.
SSD0996
5-70Starting and driving

●When the 4WD shift switch is in the 4H or 4L
position (for 4WD models)
● When driving into a strong light (i.e., sun-
light)
Action to take :
When the conditions listed above are no longer
present, turn the system off with the dynamic
driver assistance switch. Turn the DCA system
back on to use the system.
Condition B :
When the sensor window is dirty, making it
impossible to detect a vehicle ahead, the DCA
system is automatically canceled.
The chime sounds and the system warning light
(orange) will come on and the “CLEAN SENSOR”
indicator will appear.
Action to take :
If the warning light comes on, park the vehicle
in a safe place, turn the engine off. Clean the
sensor window with a soft cloth and then
perform the settings again.Condition C :
When the DCA system is not operating properly,
the chime sounds and the system warning light
(“CRUISE” orange) will come on.
Action to take :
If the warning light comes on, park the vehicle
in a safe place. Turn the engine off, restart the
engine, and turn on the DCA system again.
If it is not possible to set the system or the
indicator stays on, it may indicate that the sys-
tem is malfunctioning. Although the vehicle is
still driveable under normal conditions, have the
vehicle checked at an INFINITI retailer.
SSD0998SSD0999
5-74Starting and driving

The IBA system will remain in the last ON or OFF
state it was left in until it is manually changed
by pressing the IBA OFF switch.
Illumination of the IBA OFF indicator light with-
out a beep sound is an indication that the IBA
system is temporarily unavailable. It will occur
under the following conditions:
– When driving into a strong light (for example,sunlight)
– When the 4WD shift switch is in the 4H or 4L position (for 4WD models)
The IBA OFF indicator light will turn off when the
system returns to its normal operating condi-
tions.
For the sensor maintenance, see “Sensor main-
tenance” earlier in this section.CAUTION
During the first 1,200 miles (2,000 km), follow
these recommendations to obtain maximum
engine performance and ensure the future reli-
ability and economy of your new vehicle.
Failure to follow these recommendations may
result in shortened engine life and reduced en-
gine performance.
● Avoid driving for long periods at constant
speed, either fast or slow. Do not run the
engine over 4,000 rpm.
● Do not accelerate at full throttle in any gear.
● Avoid quick starts.
● Avoid hard braking as much as possible.
● Do not tow a trailer for the first 500 miles
(805 km). ●
Accelerate slowly and smoothly. Maintain
cruising speeds with a constant accelerator
position.
● Drive at moderate speeds on the highway.
● Avoid unnecessary stopping and braking.
Keep a safe distance behind other vehicles.
● Select a gear range suitable to road condi-
tions.
● Avoid unnecessary prolonged engine idling.
● Keep your engine tuned up.
● Follow the recommended periodic mainte-
nance schedule.
● Keep the tires inflated at the correct pres-
sure. Improper tire pressure will increase
wear and waste fuel.
● Make sure the front wheels are properly
aligned. Improper alignment will cause pre-
mature tire wear and lower fuel economy.
● Climate control operation lowers fuel
economy. Use the air conditioner only when
necessary.
● When cruising at highway speeds, it is more
economical to use the air conditioner and
leave the windows closed to reduce drag.
BREAK-IN SCHEDULE INCREASING FUEL ECONOMY
Starting and driving5-83

WARNING
●Do not attempt to raise two wheels off the
ground and shift the transmission to any
drive or reverse position with the engine run-
ning. Doing so may result in drivetrain dam-
age or unexpected vehicle movement which
could result in serious vehicle damage or
personal injury.
● Do not attempt to test a 4WD equipped ve-
hicle on a 2-wheel dynamometer or similar
equipment even if the other two wheels are
raised off the ground. Make sure you inform
test facility personnel that your vehicle is
equipped with 4WD before it is placed on a
dynamometer. Using the wrong test equip-
ment may result in drivetrain damage or un-
expected vehicle movement which could re-
sult in serious vehicle damage or personal
injury.
CAUTION
● Do not drive the vehicle in the 4HI or 4LO
position on dry hard surface roads. Driving
on dry, hard surfaces in 4HI or 4LO may
cause unnecessary noise, tire wear and in-
creased fuel consumption.
If the Four-Wheel Drive (4WD) warning light
turns on when driving on dry hard surface
roads:
– in the 4HI position, shift the 4WD shift switch to AUTO.
– in the 4LO position, stop the vehicle and shift the transmission lever to the N (Neu-
tral) position with the brake pedal de-
pressed and shift the 4WD shift switch to
AUTO.
If the 4WD warning light is still on after
the above operation, have your vehicle
checked by an INFINITI retailer as soon as
possible.
● The transfer case may be damaged if you
continue driving with the 4WD warning light
blinking.
See “ON-PAVEMENT AND OFF-ROAD DRIVING
PRECAUTIONS” earlier in this section for other
precautions for offroad driving.
INFINITI ALL-MODE 4WD SYSTEM
The all mode 4WD system provides 3 positions
(AUTO, 4HI and 4LO), so you can select the
desired drive mode according to the driving
conditions.
INFINITI ALL-MODE 4WD(if so equipped)
5-84Starting and driving

4WD shift procedure:
*1: The 4LO and 4HI indicator may flash alternately. Stop the vehicle and be sure to turn the 4WD shift switch after the transmission selector lever has
been shifted to the N (Neutral) position. If the indicator keeps flashing after the 4WD shift procedure, drive slowly without abrupt maneuvers for a while.
Then the indicator will illuminate or turn off.
· Avoid making a turn or abrupt starts while shifting to the 4LO position. Otherwise the gears may grind, damaging the drive system.
SSD1100
Starting and driving5-85

*2: While changing in and out of the 4LO position, the engine must be running. Otherwise, the shift will not take place and the 4LO indicator will not
be on or flashing.
*3: Make sure that the 4LO indicator turns on when shifting the 4WD shift switch to the 4L position. The Vehicle Dynamic Control (VDC) off indicator
light will also turn on when 4L is selected. (See “VEHICLE DYNAMIC CONTROL (VDC) SYSTEM” later in this section.)
5-86Starting and driving

The 4WD shift switch is used to select the 4WD
mode depending on the driving conditions.
There are 3 types of drive modes available,
AUTO, 4HI and 4LO.
The 4WD shift switch electronically controls the
transfer case operation. Rotate the switch to
move between each mode, AUTO, 4H and 4L.
You must depress the 4WD shift switch to select
4L, and the vehicle MUST be stationary and the
selector lever in the N (Neutral) position when
changing into or out of 4L.
WARNING
●When parking, apply the parking brake be-
fore stopping the engine and make sure that
the 4WD shift indicator is on and the ATP
warning light turns off. Otherwise, the ve-
hicle could unexpectedly move even if the
automatic transmission is in the P (Park)
position.
● The 4LO and 4HI indicators must stop blink-
ing and the 4LO or 4HI indicator must remain
illuminated or turn off before shifting the
transmission into gear. If the selector lever
is shifted from the N (Neutral) position to any
other gear while the 4LO and 4HI indicators
are blinking alternately, the vehicle may
move unexpectedly.
CAUTION
● Never shift the 4WD shift switch between 4L
and 4H while driving.
● The 4HI position provides greater traction.
Avoid excessive speed, as it will cause in-
creased fuel consumption and higher oil
temperatures, and could damage drivetrain
component. Speeds over 62 MPH (100 km/h)
in 4HI is not recommended.
● The 4LO position provides maximum trac-
tion. Avoid raising vehicle speed exces-
sively, as the maximum speed is approxi-
mately 31 MPH (50 km/h).
● When driving straight, shift the 4WD shift
switch to the AUTO or 4H position. Do not
move the 4WD shift switch when making a
turn or reversing.
● Do not shift the 4WD shift switch (between
AUTO and 4H) while driving on steep down-
hill grades. Use the engine brake and low
automatic transmission gears for engine
braking.
● Do not operate the 4WD shift switch (be-
tween AUTO and 4H) with the rear wheels
spinning. ●
Do not drive on dry hard surface roads in the
4HI or 4LO position. Driving on dry hard sur-
faces in 4HI or 4LO may cause unnecessary
noise and tire wear. INFINITI recommends
driving in the AUTO position under these
conditions.
● The 4WD transfer case may not be shifted
between 4HI and 4LO at low ambient tem-
peratures and the 4LO and 4HI indicators
may blink even when the 4WD shift switch is
shifted. After driving for a while you can
change the 4WD shift switch between 4H
and 4L.
When driving on rough roads,
● Drive carefully according to the road surface
conditions.
When the vehicle is stuck,
● Place stones or wooden blocks under the
tires to free the vehicle.
● Set the 4WD shift switch to 4H or 4L.
● If it is difficult to free the vehicle, repeat
forward and backward movement to increase
the movement.
● If the vehicle is stuck deep in mud, tire
chains may be effective.
Starting and driving5-87