2011 INFINITI QX cruise control

8. Parking brake release warning
This warning appears when the vehicle speed is
above 4 MPH (7 km/h) and the parking brake is
applied.
9. Low fuel warning
This warning appears when the fuel level in the
tank is getting low. Refuel as soon as it is
convenient, preferably before the fuel gauge
reaches the 0 (Empty) position.
There is a small reserve of fuel remaining in the
tank when the fuel gauge reaches the 0 (Empty)
position.
10. Low washer fluid warning
This warning appears when the washer tank
fluid is at a low level. Add washer fluid as
necessary. (See “WINDOW WASHER FLUID” in
the “8. Maintenance and do-it-yourself” sec-
tion.)
11. Door/lift gate open warning
(ignition switch is in the ON position)
This warning appears if any of the doors and/or
the lift gate are open or not closed securely. The
vehicle icon indicates which door or the lift gate
is open on the display.
12. Loose fuel cap warning (if so
equipped)
This warning appears when the fuel-filler cap is
not tightened correctly after the vehicle has
been refueled. (See “FUEL-FILLER CAP” in the
“3. Pre-driving checks and adjustments” sec-
tion.)
13. Check tire pressure warning (if so
equipped)
This warning appears when the low tire pres-
sure warning light in the meter illuminates and
low tire pressure is detected. If this warning
appears, stop the vehicle and adjust the tire
pressure to the recommended COLD tire pres-
sure shown on the Tire and Loading Information
label. (See “Low tire pressure warning light”
earlier in this section and “TIRE PRESSURE
MONITORING SYSTEM (TPMS)” in the “5. Start-
ing and driving” section.)
14. “TIMER” indicator
This indicator appears when the set “TIMER”
indicator activates. You can set the time for up
to 6 hours. (See “TRIP COMPUTER” later in this
section.)
15. Low outside temperature warning
This warning appears if the outside temperature
is below 37°F (3°C). The warning can be set not
to be displayed. (See “TRIP COMPUTER” later in
this section.)
16. Four-Wheel Drive (4WD) shift
indicator (4WD models)
This indicator shows the Four-Wheel Drive
(4WD) driving mode (AUTO, 4HI or 4LO) that is
selected by the 4WD shift switch. (See “INFINITI
ALL-MODE 4WD” in the “5. Starting and driv-
ing” section.)
17. Intelligent Cruise Control (ICC)
system MAIN switch indicator (if so
equipped)
The indicator is displayed when the Intelligent
Cruise Control (ICC) system main switch is
pushed. When the main switch is pushed again,
the indicator disappears. While the main switch
indicator is displayed, the ICC system is opera-
tional. (See “INTELLIGENT CRUISE CONTROL
(ICC) SYSTEM” in the “5. Starting and driving”
section.)
2-24Instruments and controls

5 Starting and driving
Precautions when starting and driving.............. 5-2
Exhaust gas (carbon monoxide) .................. 5-2
Three-way catalyst ............................. 5-2
Tire Pressure Monitoring System (TPMS) ......... 5-3
Avoiding collision and rollover ................... 5-6
On-pavement and off-road driving
precautions .................................... 5-6
Off-road recovery ............................... 5-7
Rapid air pressure loss ......................... 5-7
Drinking alcohol/drugs and driving .............. 5-8
Driving safety precautions ...................... 5-8
Push-button ignition switch .......................5-10
Operating range for engine start function ........5-10
Push-button ignition switch positions ............5-11
Emergency engine shut off ......................5-12
Intelligent Key battery discharge .................5-12
Before starting the engine .........................5-13
Starting the engine ................................ 5-13
Driving the vehicle ................................ 5-14
Engine protection mode ......................... 5-14
Automatic transmission ......................... 5-15
Parking brake ..................................... 5-19
Lane Departure Warning (LDW)/prevention (LDP)
system (if so equipped) ........................... 5-20Lane Departure Warning (LDW) system
..........5-20
Lane Departure Prevention (LDP) system .........5-24
Blind spot warning (BSW) system
(if so equipped) .................................. 5-29
Bsw system operation ......................... 5-30
Bsw driving situations ......................... 5-33
Bsw malfunction .............................. 5-36
System maintenance .......................... 5-37
Cruise control .................................... 5-37
Precautions on cruise control ...................5-37
Cruise control operations ......................5-38
Intelligent Cruise Control (ICC) system
(if so equipped) .................................. 5-39
Selecting vehicle-to-vehicle distance
control mode .................................. 5-41
Vehicle-to-vehicle distance control mode .........5-41
Precautions on vehicle-to-vehicle distance
control mode .................................. 5-41
Vehicle-to-vehicle
distance control mode
operation ..................................... 5-43
Conventional (FIXED SPEED) cruise control
mode ........................................ 5-58
Preview function (for Intelligent Cruise
Control (ICC) system equipped model) ...........5-62

Distance Control Assist (DCA) system
(if so equipped).................................. 5-62
Precautions on distance control assist
system ....................................... 5-63
Distance control assist operation ...............5-64
Forward Collision Warning (FCW) system
(if so equipped) .................................. 5-75
Precautions on FCW system ....................5-76
Intelligent brake assist (IBA) system
(if so equipped) .................................. 5-80
Precautions on IBA system .....................5-80
Break-in schedule ................................ 5-83
Increasing fuel economy .......................... 5-83
INFINITI all-mode 4wd (if so equipped)............5-84
INFINITI all-mode 4wd system................. 5-84
4wd shift switch .............................. 5-88
4wd shift indicator ............................ 5-89
4wd warning light ............................. 5-89
Hill start assist system ........................... 5-91
Parking/parking on hills .......................... 5-92
Tow mode ....................................... 5-93Snow mode
...................................... 5-93
Power steering ................................... 5-94
Brake system .................................... 5-94
Braking precautions ........................... 5-94
Parking brake break-in ......................... 5-94
Brake assist ..................................... 5-95
Brake assist .................................. 5-95
Preview function (Intelligent Cruise Control
system equipped models) ......................5-95
Anti-lock Braking System (ABS) .................5-97
Vehicle Dynamic Control (VDC) system .............5-98
Vehicle Dynamic Control (VDC) OFF switch ......5-100
Cold weather driving ............................. 5-101
Freeing a frozen door lock .....................5-101
Antifreeze .................................... 5-101
Battery ....................................... 5-101
Draining

of coolant water ...................... 5-101
Tire equipment ................................ 5-101
Special winter equipment ......................5-101
Driving on snow or ice ......................... 5-101
Engine block heater (if so equipped) ...........5-102

How to enable/disable the LDP system using
the settings menu :
Perform the following steps to enable or disable
the LDP system.
1. Push the SETTING1button and highlight
the “Driver Assistance” key on the display
using the INFINITI controller. Then push
the ENTER
2button.
2. Highlight the “Dynamic Assistance Set- tings” key, and push the ENTER
2but-
ton.
3. Highlight the “Lane Departure Preven-tion” key, select ON (enabled) or OFF
(disabled) and push the ENTER
2button.
For the DCA system, see “DISTANCE CONTROL
ASSIST (DCA) SYSTEM” later in this section.
Automatic deactivation
Condition A :
The warning and assist functions of the LDP
system are not designed to work under the
following conditions:
●When you operate the lane change signal
and change the traveling lanes in the direc- tion of the signal. (The LDP system will be
deactivated for approximately 2 seconds af-
ter the lane change signal is turned off.)
● When the vehicle speed lowers to less than
approximately 45 MPH (70 km/h).
After the above conditions have finished and the
necessary operating conditions are satisfied, the
warning and assist functions will resume.
Condition B :
The assist function of the LDP system is not
designed to work under the following condi-
tions (warning is still functional):
● When the brake pedal is depressed.
● When the steering wheel is turned as far as
necessary for the vehicle to change lanes.
● When the accelerator pedal is depressed
while the brake control assist is provided.
● When the Intelligent Cruise Control (ICC)
approach warning occurs.
● When the hazard warning flashers are oper-
ated.
● When driving on a curve at high speed.
After the above conditions have finished and
the necessary operating conditions are satis-
fied, the LDP brake control assist function will
resume.
SSD1103
Starting and driving5-27

SYSTEM MAINTENANCE
The two radar sensor units1for the BSW
system is located near the rear bumper. Always
keep the area near the radar sensors clean. Do
not attach stickers (including transparent mate-
rial), install accessories or apply additional
paint near the radar sensors. Do not strike or
damage the area around the radar sensors.
Consult an INFINITI retailer if the area around
the radar sensors is damaged due to a collision.
Radio frequency statement
This device complies with part 15 of the FCC
Rules and RSS-310 of Industry Canada.
Operation is subject to the following two con-
ditions:
1. This device may not cause harmful inter- ference.
2. This device must accept any interference received, including interference that may
cause undesired operation.
Frequency of operation: 24.05GHz — 24.25GHz
Field Strength: Not greater than 2.5V/m peak
(0.25V/m average) at a distance of 3 m
The manufacturer is not responsible for any
radio or TV interference caused by unauthorized
modifications to this equipment. Such modifi-
cations could void the user’s authority to oper-
ate the equipment.
PRECAUTIONS ON CRUISE CONTROL
●If the cruise control system malfunctions, it
will cancel automatically. The CRUISE indica-
tor light on the meter panel will then blink to
warn the driver.
● If the engine coolant temperature becomes
excessively high, the cruise control system
will be canceled automatically.
● If the CRUISE indicator light blinks, turn the
cruise control main switch off and have the
system checked by your INFINITI retailer.
● The CRUISE indicator light may sometimes
blink when the cruise control main switch is
turned ON while pushing the RESUME/
ACCELERATE, SET/COAST or CANCEL switch.
To properly set the cruise control system,
perform the steps below in the order indi-
cated.
SSD1085
CRUISE CONTROL
Starting and driving5-37

WARNING
Do not use the cruise control when driving un-
der the following conditions:
●when it is not possible to keep the vehicle at
a set speed
● in heavy traffic or in traffic that varies in
speed
● on winding or hilly roads
● on slippery roads (rain, snow, ice, etc.)
● in very windy areas
Doing so could cause a loss of vehicle control
and result in an accident.
1. RESUME/ACCELERATE switch
2. SET/COAST switch
3. CANCEL switch
4. Cruise control MAIN switch
CRUISE CONTROL OPERATIONS
The cruise control allows driving at a speed
between 25 to 90 MPH (40 to 144 km/h) without
keeping your foot on the accelerator pedal.
To turn on the cruise control, push the MAIN
switch on. The CRUISE indicator will come on. To set cruising speed,
accelerate your vehicle to
the desired speed, push the SET/COAST switch
and release it. Take your foot off the accelerator
pedal. Your vehicle will maintain the set speed.
● To pass another vehicle, depress the accel-
erator pedal. When you release the pedal,
the vehicle will return to the previously set
speed.
● The vehicle may not maintain the set speed
on winding or hilly roads. If this happens,
drive without the cruise control.
To cancel the preset speed, follow any of these
methods:
a) Push the CANCEL switch.
b) Tap the brake pedal.
c) Move the selector lever to the N (Neutral) position.
d) Turn the MAIN switch off. The CRUISE indicator light will turn off.
●If you depress the brake pedal while pushing
the RESUME/ACCELERATE or SET/COAST
switch and reset at the cruising speed, the
cruise control will disengage. Turn the MAIN
switch off once and then turn it on again.
SSD0694
5-38Starting and driving

●The cruise control will automatically cancel if
the vehicle slows more than 7 MPH (12 km/h)
below the set speed.
● If you move the selector lever to N (Neutral)
position, the cruise control will be canceled.
To reset at a faster cruising speed, use one of
the following methods:
● Depress the accelerator pedal. When the
vehicle attains the desired speed, push and
release the SET/COAST switch.
● Push and hold the RESUME/ACCELERATE
switch. When the vehicle attains the speed
you desire, release the switch.
● Push, then quickly release the
RESUME/ACCELERATE switch. Each time you
do this, the set speed will increase by about
1 MPH (1.6 km/h). To reset at a slower cruising speed,
use one of
the following methods:
● Lightly tap the brake pedal. When the ve-
hicle attains the desired speed, push the
SET/COAST switch and release it.
● Push and hold the SET/COAST switch. Re-
lease the switch when the vehicle slows
down to the desired speed.
● Push, then quickly release the SET/COAST
switch. Each time you do this, the set speed
will decrease by about 1 MPH (1.6 km/h).
To resume the preset speed, push and release
the RESUME/ACCELERATE switch. The vehicle
will resume the last set cruising speed when the
vehicle speed is over 25 MPH (40 km/h). The Intelligent Cruise Control (ICC) system au-
tomatically maintains a selected distance from
the vehicle traveling in front of you according to
that vehicle’s speed (up to the set speed), or at
the set speed when the road ahead is clear.
The ICC function can be set to one of two cruise
control modes:
●
Vehicle-to-vehicle distance control mode:
For maintaining a selected distance between
your vehicle and the vehicle in front of you
up to the preset speed.
● Conventional (fixed speed) cruise control
mode:
For cruising at a preset speed.
WARNING
● Always drive carefully and attentively when
using either cruise control mode. Read and
understand the Owner’s Manual thoroughly
before using the ICC system. To avoid seri-
ous injury or death, do not rely on the system
to prevent accidents or to control the vehi-
cle’s speed in emergency situations. Do not
use the ICC system except in appropriate
road and traffic conditions.
INTELLIGENT CRUISE CONTROL (ICC)
SYSTEM (if so equipped)
Starting and driving5-39

●In the conventional (fixed speed) cruise con-
trol mode, a warning chime will not sound to
warn you if you are too close to the vehicle
ahead. Pay special attention to the distance
between your vehicle and the vehicle ahead
of you or a collision could occur.
1. Vehicle-to-vehicle distance control mode
2. Conventional (fixed speed) cruise control
mode
Push the MAIN switchAto choose the cruise
control mode between the vehicle-to-vehicle
distance control mode
1and the conventional
(fixed speed) cruise control mode
2.
To choose the vehicle-to-vehicle distance con-
trol mode
1, quickly push and release the
MAIN switch
A. To choose the conventional
(fixed speed) cruise control mode
2, push and
hold the MAIN switch
Afor longer than ap-
proximately 1.5 seconds. Once a control mode is activated, it cannot be
changed to the other cruise control mode. To
change the mode, push the MAIN switch once to
turn the system off. Then push the MAIN switch
again to turn the system back on and select the
desired cruise control mode.
Always confirm the setting in the ICC system
display.
For the vehicle-to-vehicle distance control
mode, see the following description. For the
conventional (fixed speed) cruise control mode,
see “CONVENTIONAL (FIXED SPEED) CRUISE
CONTROL MODE” later in this section.
SSD1051
5-40Starting and driving